LD ON mode in the test mode oscillates with the laser forcibly. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : See page 55. DV-696AV-S...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DV-696AV-S...
For WVXT5 type INSTRUCTION BOOK (E) INSTRUCTION BOOK (E/I) INSTRUCTION BOOK (G/F) INSTRUCTION BOOK (S/D) INSTRUCTION BOOK (R) 7-10,17 "Operating Instructions" For WYXZT5, YXZTUR5 types POLY BAG INSTA5 TRANSMITTER CORD,RCA PIN BATTERY,MANGAN PACKAGE PACKAGE GIFT SHEET PACKAGE PACKAGE PACKAGE,PAD DV-696AV-S...
Page 7
Carton Label See Contrast table (2) Instruction Book See Contrast table (2) Instruction Book See Contrast table (2) (2) CONTRAST TABLE DV-696AV-S/WVXT5, /YXZTUR5, DV-696AV-K/WYXZT5, /YXZTUR5 and DV-696AV-S/WYXZT5 are constructed the same except for the following : DV-696AV-S/ DV-696AV-S/ DV-696AV-S/ DV-696AV-K/ DV-696AV-K/ Mark No.
Page 9
See Contrast table (2) NSP 101P Glass LED 713WPA0385 NSP 25 Sheet,Jack 3 See Contrast table (2) (2) CONTRAST TABLE DV-696AV-S/WVXT5, /YXZTUR5, DV-696AV-K/WYXZT5, /YXZTUR5 and DV-696AV-S/WYXZT5 are constructed the same except for the following : DV-696AV-S/ DV-696AV-S/ DV-696AV-S/ DV-696AV-K/ DV-696AV-K/ Mark No.
CD2301 NOTE: Applying positions AA, AB and AC for the CLASS PART NO. MARK PART NAME grease are displayed for this section. GREASE GEM1018 G-555G Check if the correct grease is applied for each GYA1001 G-313Y position. GEM1036 FL-78A DV-696AV-S...
65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 EEPROM TP4109 B4010 PWR# MMZ1608R102CT PCE# PRD# D_GND NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-696AV-S...
Page 19
TP4099 101102103104105106107108109110111112113114115116117118119120121122123124125126127128 V+3E 0.0082 B V+3E DGND DGND FLDC+ TP4100 FLDC+ -28V TP4101 -28V FLDC- TP4102 FLDC- R4084 C4091 0.1 B W846 R4051 RESET TP4110 RESET NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-696AV-S...
3.5 DVD MT PCB ASSY(2/7) DVD MT PCB ASSY (A2J003A130) MEMORY BLOCK DV-696AV-S...
Page 21
16Mbit FLASH IC S29AL016D70TFI020 NOTE :THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE : THE DC VOLTAGE EACH PART WAS OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-696AV-S...
KTC3875S_Y_RTK VREF_S W801 12.5 12.5 B8001 ACLK REF GEN Q8012 MMZ1608R102CT KTC3875S_Y_RTK VREF_F ABCK0 ASDAT0 ALRCK V+5A V+3A1 C8025 330P CH W866 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DV-696AV-S...
Page 25
220 +-1% 220 +-1% C8040 R8041 R8063 SR C 10K +-1% 10K +-1% R8040 270K R8064 CAUTION: DIGITAL TRANSISTOR J8001 RCA-207B-02 18K +-1% LS/RS/C/LFE NOTE:THE DC VOLTAGE EACH PART WAS J8002 MEASURED WITH THE DIGITAL TESTER RCA-405A-06 DURING PLAYBACK. DV-696AV-S...
(R/CR) : VIDEO SIGNAL ROUTE (R/CR ) (G/Y) : VIDEO SIGNAL ROUTE (G/Y ) (B/CB) : VIDEO SIGNAL ROUTE (B/CB ) W892 : AUDIO DATA SIGNAL ROUTE (DA) : AUDIO SIGNAL ROUTE (Digital) : AUDIO SIGNAL ROUTE (L ch) DV-696AV-S...
Page 27
(CP503) CP7301 IMSA-9604S-12C 21PIN-G/D-Y (G/Y) 21PIN-B/D-U (B/CB) 21PIN-R/D-V (R/CR) P-H/I-L_RGB-H RGB-H ASP/FS CVBS AUDIO L AUDIO R S_Y_OUT (SY) S_C_OUT (SC) CVBS_OUT 4CH BUS SW IC IC7302 SN74CBT3257PWR W895 (GY) (B/CB) (R/CR) CVBS/Y/U/V S-VIDEO OUT J7302 J7301 RCA-405A-08 DIN-409A DV-696AV-S...
FROM/TO POWER CP4003 (CP502) A2001WV2-14P P.CON+12V AT+12V for MUTE P.CON+5V P.CON+6V GND(M) AT+3.3V +3.3V TP4031 AT+3.3V STBY L GND(D) FL DC- FL DC+ -28V NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-696AV-S...
Page 31
(MPEG/SDRAM/FLASH) W821 V+3E (FIP/LED/IR/RESET) V+3E V+1R8 (CORE) V+1R8 C4105 R4058 100P CH PWDN# FLDC- FLDC+ -28V D_GND FRROM/TO MEMORY D_GND NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-696AV-S...
EJECT SW666 EVQ11L05R FFC(1.0mm pitch) CD602 2H091303 CP603 CP602 (CP602) (CP603) 00_6232_009_102_800+ 00_6232_009_102_800+ Vout STOP STOP PLAY/+SKIP PLAY/+SKIP PAUSE/-SKIP PAUSE/-SKIP OS651 V+3E V+3E C668 POWER POWER ROM-N340TAO 0.01 B W804 OPERATION 2 PCB ASSY (A2I802A280) B C G H DV-696AV-S...
Page 33
FLDC+ -28V -28V FLDC- FLDC- NOTE : THE DC VOLTAGE EACH PART WAS MEASURED NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME WITH THE DIGITAL TESTER DURING PLAYBACK. OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-696AV-S...
REPLACE WITH SAME TYPE AND RATINGS OF FUSE. ATTENTION: LES PIECES REPAREES PAR UN ETANT CAUTION: SINCE THESE PARTS MARKED BY DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES N'UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES DV-696AV-S...
Page 35
THE DC VOLTAGE EACH PART WAS NOTE : THE RESISTOR MARKED F IS FUSE RESISTOR. THE TIME OF PRINTING AND SUBJECT TO CHANGE MEASURED WITH THE DIGITAL TESTER THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP WITHOUT NOTICE DURING PLAYBACK. IS NON POLAR ONE. DV-696AV-S...
LES PIECES REPAREES PAR UN ETANT CAUTION: SINCE THESE PARTS MARKED BY DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR N'UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES DV-696AV-S...
Page 37
DVD_RGB_H_OUT Q8105 KRA102SRTK R8109 DVD_RGB_H_OUT Q8104 68 +-1% KRC104SRTK NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-696AV-S...
Resistor array 3-terminal regulator LOADING MOTOR LOADING MOTOR PCB ASSY PCB ASSY (INSERTED PARTS) (CHIP MOUNTED PARTS) SIDE A SIDE B CD2302 CP2302 M2603 M2603 SW PCB ASSY LOADING MOTOR CD2301 M2602 SLED MOTOR CD2301 M2601 SPINDLE MOTOR CP2303 DV-696AV-S...
J8001 RCA JACK 060R451009 There is no Service Parts J7301 RCA JACK 063R700013 J7302 RCA JACK 060R451010 CP5901 CONNECTOR 0694YJ3018 X4001 CRYSTAL (27MHz) 100GT02720 LOADING MOTOR PCB ASSY There is no Service Parts OPERATION PCB ASSY SEMICONDUCTORS IC651 IC PT6315 IF4K063150 DV-696AV-S...
• Soldering time: Within 3 seconds • Soldering combination: Sn-3.0Ag-0.5Cu • When Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to prevent the Flux smoke from it. Short circuit using a soldering iron. Pick Up PCB Fig. 1 DV-696AV-S...
• After going into test mode, if you play back the disc, "DISC-NON" is displayed. • The video signal and the audio signal are outputted during the test mode. • The SKIP key and the SCAN key are effective during the test mode. TEST MODE: OFF POWER GGF1381 Test mode remote control unit DV-696AV-S...
3 LD ON DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n). : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n). DV-696AV-S...
• Place the unit on a workstation equipped to protect against static electricity, such as conductive mat. • Soldering iron with ground wire or ceramic type is used. • A worker needs to use a ground conductive wrist strap for body. DV-696AV-S...
: [NTSC] PAL system : [PAL] Automatic setting : [AUTO] Scart terminal output [SK – ∗ ∗] (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] DV-696AV-S...
• Region confirmation mode (ESC + A.MON [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys) After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. DV-696AV-S...
Character in bold : Item name : Information display 1 Destination indication Display it according to model information set from the FL Driver IC. 2 Region No. 3 ROM number 4 REG CHK 5 SUM CHK 6 CHIP VERSION DV-696AV-S...
%%e -2 : NG 7.0e -4 : NG 3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors) Note: ∗ Error of AV1 is not supported in this player. Indication plan contents Character in bold : Item name : Information display DV-696AV-S...
Measure the voltage between the two ends of R2320 or R2322 on the DVD MT PCB Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded. To OPTICAL PICKU DVD MT PCB ASSY CP2301 Front side SIDE A DV-696AV-S...
DVD MT PCB Assy Check the video signal path between DVD IC (DVD MT Assy IC4002) displayed on the monitor Video circuit after DVD IC and video-out terminal (see the block diagram) (The FL display lights. The (IC4002) mechanism does not work.) DV-696AV-S...
Page 63
Is there a problem with the format of the disc ? (block noise, freeze, other) No sound Is signal output from IC8003, 8004, 8005-pin 7 and pin 8 on the DVD (Picture is normal) DVD MT PCB Assy MT Assy ? Audio DAC IC (IC8003, 8004, 8005) DV-696AV-S...
Page 64
Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be (DVD MT PCB Assy : IC4002) generated, because the DVD processing is performed by a single chip. 64M SDRAM No power. (DVD MT PCB Assy : IC4005) Block noise is generated during playback. DV-696AV-S...
1-4: DVD PCB (Refer to Fig. 1-4) Remove the 5 screws 1. Power PCB Remove the screws 2 . 3. Remove the 4 screws 3. Remove the DVD PCB in the direction of arrow DVD MT PCB Fig. 1-2 Fig. 1-4 DV-696AV-S...
Page 67
3 supports 1. between A and B. Fig. 2-3-D Remove the Plate Clamper, Magnet Clamper and Clamper. Check Hook Check Hook Plate Clamper Magnet Clamper Main Frame Loading Motor PCB Ass’y Clamper Check Hook Fig. 2-5-A Fig. 2-3-E DV-696AV-S...
Page 68
Remove the Switch PCB Ass'y. 8.0 ± 0.2 mm Remove the screw 4. Remove the Gear Feed. Feed Motor Remove the 2 screws 5. Remove the Feed Motor. Remove the Gear Motor. Safety surface for pressing of the insert. Fig. 2-7-C DV-696AV-S...
Page 69
When installing the FFC, fold it correctly and install it as shown from Fig. 2-8. NOTE Do not make the folding lines except the specified positions for the FFC. [ 24 pin FFC ] Printing _Serface 79 ± 1 mm Reinforcement Plat To Pick Up PCB Fig. 2-8 DV-696AV-S...
Page 71
TV Encoder Module Videop RF Amplifier Video DAC Servo IO Servo Motor Processor Video Drive Processor interlacer Spindle Control FLASH MPEG-1/2 Audio JPEG Memory Video Decoder Controller DRAM System Audio Parser Audio Output CPPM/CPRM SPDIF System GPIO 32-bit RISC IR/VFD DV-696AV-S...
Page 72
While External FLASH size <= 2MB: 45 NC – – Version AD input port 0, or DVDD3 – 3.3V power pin for internal digital circuitry GPIO FG(Diogital pin) – Motor Hall sensor input, or Version AD input 8 90 ALE Microcontroller address latch enable DV-696AV-S...
Page 73
133 RD9 DRAM data 9 185 NC – – 134 DVSS – 3.3V Ground pin for internal digital circuitry 186 NC – – 135 RD8 DRAM data 8 187 NC – – 136 DQS1 GPIO 188 NC – – DV-696AV-S...
Page 74
236 LPFIP The positive input terminal of loop filter amplifier GPIO 237 LPFIN The negative input terminal of loop filter amplifier 212 DVDD3 – 3.3V power pin for internal digital circuitry 238 LPFOP The positive output of loop filter amplifier DV-696AV-S...
Page 75
RF path. Connect 246 RFRPAC RF ripple detect input (through AC-coupling) an external 15K resistor to this pin and 247 HRFZC High frequency RF ripple zero crossing AVSS 248 CRTPLP Defect level filter capacitor connecting 256 AVDD3 – Analog power 3.3V DV-696AV-S...
WMA files – do not use for other file types) product. Formore detailed information on the DualDisc Formore detailed information on the DualDisc specification, please refer to the disc specification, please refer to the disc manufacturer or disc retailer. manufacturer or disc retailer. DV-696AV-S...
Check the DVD-R/RW or CD-R/RW software Check the DVD-R/RW or CD-R/RW software disc boxes for additional compatibility disc boxes for additional compatibility information. information. DV-696AV-S...
8 Display 16 HDMI indicator Description of the display. Lights when this player is recognized by another HDMl or DVI/HDCP compatible component. Compatible This mark indicates compatibility with DVD-RW discs recorded on a DVD recorder in Video Recording mode. DV-696AV-S...
Press to pause playback; press again to restart. 12 PLAY MODE Press to display the Play Mode menu. (You can also get to the Play Mode menu by pressing HOME MENU and selecting Play Mode). Press to jump to the beginning of the current DV-696AV-S...
Page 80
Use to select menu options, etc. playing. 24 ZOOM 18 MENU Press to change the zoom level. Press to display a DVD disc menu, or the Disc Navigator if a VR format DVD-RW, CD, Video CD , MP3, WMA or JPEG disc is loaded. DV-696AV-S...
• Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Position to be cleaned Cleaning tools Cleaning tools Remark Remark Pickup leneses Cleaning liquid : GEM1004 Refer to "2.3 06 DVD MECHA SECTION" and Cleaning paper : GED-008 Refer to "7.3 DVD DECK SECTION" DV-696AV-S...