Table of Contents
Advertisement
12
www.raider.bg
reach of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool. Power
tools are dangerous in the hands of untrained
users.
1.4.5. Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
1.4.6. Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
1.4.7. Use the power tool, accessories
and tool bits etc. in accordance with these
instructions, taking into account the working
conditions and the work to be performed. Use
of the power tool for operations different from
those intended could result in a hazardous
situation.
1.4.8. Noise&Vibration Information.
Measured
sound
according
to
EN
A-weighted noise levels of the product are:
Sound pressure level 72.2 dB(A);
Sound power level 85.2 dB(A).
Uncertainty K=3 dB.
Wear hearing protection!
Vibration total values (triad vector sum)
determined according to EN 61029:
Vibration emission value ah =3.80 m/s2
Uncertainty K =1.5 m/s2.
The vibration emission level given in this
information sheet has been measured in
accordance with a standardised test given
in EN 61029 and may be used to compare
one tool with another. It may be used for a
preliminary assessment of exposure. The
declared vibration emission level represents
the main applications of the tool. However if
the tool is used for different applications, with
different accessories or poorly maintained,
the vibration emission may differ. This may
significantly increase the exposure level
over the total working period. An estimation
of the level of exposure to vibration should
also take into account the times when the tool
is switched off or when it is running but not
actually doing the job. This may significantly
reduce the exposure level over the total
working period.
values
determined
61029.
Typically
1.4.9. Keep the table flat and do not scratch
or press the table.
1.4.10. Do not put hands anywhere near
the blade whist it is rotating.
1.4.11 Do not attempt to free a jammed
blade without first switching off or removing
the plug from the mains power supply.
1.4.12. Keep water full in the tank when you
operate the cutter.
1.4.13. Do not use any solvents for instead
water in this tool.
1.4.14. Disconnect the tool from power
source when not in use or before servicing.
2. SPECIFIC SAFETY RULES
2.1. Ensure that the directional arrow on
the blade corresponds with the rotational
direction of the motor.
2.2. Periodically check to be sure the
locking arbor bolt is tight, and the blade is
securely fastened to the arbor shaft.
2.3. Check the blade carefully to see if
cracked or damaged before use. If cracked or
damaged, replace it immediately.
the
2.4. Only use a RCD-protected power
source or connect to an electrical power point
using an approved RCD circuit breaker. This
is an essential safety precaution.
2.5. Keep the cord away from the cutting
area and position it so that it will not be
caught on the work piece.
2.6. Before switching on, check that
all spanners and setting tools have been
removed.
2.7. Never try to cut freehand. Only cut
tile that is securely held against the fence of
the sliding table or the mitre gauge. Never
try to cut pieces that are too small to be held
securely or that do not allow you to keep your
hands safely away from the blade.
2.8. Ensure that the work piece that will be
cut off has sufficient room to move sideways.
Failure to do so may result in the off-cut
binding against the blade.
2.9. Never cut more than one tile at a time.
2. 10. Ensure that the table and surrounding
area are clear with the exception of the tile to
be cut.
2.11. Before cutting a tile piece, let the
blade run freely for a few seconds. If it makes
an unfamiliar sound or vibrates excessively,
switch it off immediately and disconnect from
the power supply to find the source of the
Advertisement
Table of Contents
