Configuration Number Matrix - Graco Husky 1050 Operation

Pump Matrix
Pump Matrix
Check the identification plate (ID) for the Configuration Number of your
pump. Use the following matrix to define the components of your pump.
Sample Configuration Number: 1050A-PA01AA1SSBNBNPT
1050 A P
Pump Wetted Drive
Size Section Identifier
Material
Pump Wetted Section Material
Size
1050 A Aluminum
1050 C Conductive
Polypropylene
1050 F PVDF
1050 H‡ Hastelloy
1050 P Polypropylene
1050 S‡ Stainless Steel
, ‡, , or : See ATEX Certifications, page 5.
Contains pressure relief valve.
Check Valve Seats
AC Acetal
AL Aluminum
BN Buna-N
FK FKM Fluoroelastomer
GE
®
Geolast
PP Polypropylene
PV PVDF
SP ®
Santoprene
SS 316 Stainless Steel
TP TPE
4
A01A A1 SS
Center Fluid Seats Balls Diaphragms
Section and Covers and
Air Valve Manifolds
Drive Center Section and Air
Identifier Valve Material
P
Pneumatic
Aluminum
Conductive
Polypropylene
Polypropylene
Check Valve Balls
AC Acetal
BN Buna-N
CR Polychloroprene Standard
CW Polychloroprene Weighted
EP EPDM
FK FKM Fluoroelastomer
GE Geolast
PT PTFE
SD 440C Stainless Steel
SP Santoprene
SS 316 Stainless Steel
TP TPE
BN BN PT
Manifold
O-Rings
Air Valve/Monitoring
A01A Standard
Pulse Count 
A01B
DataTrak 
A01C
A01D Remote
A01E Optional FKM Seals
A01H Standard, Gray
AC1A CSA-Compliant
AU1A UL-Listed; Fuel transfer
AU3A UL-Listed; Fuel
dispense
C01A Standard
Pulse Count 
C01B
DataTrak 
C01C
C01D Remote
P01A Standard
P01B Pulse Count
P01C DataTrak
P01D Remote
Diaphragm
BN Buna-N
CO Polychloroprene Overmolded
FK FKM Fluoroelastomer
GE Geolast
PO PTFE/EPDM Overmolded
PS PTFE/Santoprene Two-Piece
PT PTFE/EPDM Two-Piece
SP Santoprene
TP TPE
PART NO. CONFIGURATION NO. SERIAL NO.
DATE CODE SERIES MAX WPR PSI-bar MADE IN
ID
Fluid Covers and Manifolds
A1 Aluminum, standard ports, inch
A2 Aluminum, standard ports, metric
C1 Conductive polypropylene, center
flange
C2 Conductive polypropylene, end
flange
F1 PVDF, center flange
F2 PVDF, end flange
H1 Hastelloy, standard ports, inch
H2 Hastelloy, standard ports, metric
P1 Polypropylene, center flange
P2 Polypropylene, end flange
S1 Stainless steel, standard ports, inch
S2 Stainless steel, standard ports,
metric
S5-1 Stainless steel, center flange,
horizontal outlet port
S5-2 Stainless steel, center flange, vertical
outlet port
S5-3 Stainless steel, center tri-clamp,
horizontal inlet and outlet port
Manifold O-Rings
— Models with
Buna-N, FKM
Fluoroelastomer
or TPE seats do
not use o-rings.
PT PTFE
312877ZAD
ti14103a