Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec IDS 20
Summary of Contents for Trotec IDS 20
- Page 1 IDS 20 / IDS 30 ORIGINAL INSTRUCTIONS OIL HEATER...
-
Page 2: Table Of Contents
Children shall not play with the appliance. Cleaning and This signal word indicates important information (e.g. user maintenance shall not be made by children material damage), but does not indicate hazards. without supervision. oil heater IDS 20 / IDS 30... - Page 3 • The mains connection must correspond to the specifications in the Technical annex. • Insert the mains plug into a properly fused mains socket. oil heater IDS 20 / IDS 30...
- Page 4 Do not touch the mains plug with wet or damp hands. Warning Hold onto the mains plug while pulling the power cable The device must not be covered, there is an imminent out of the mains socket. fire hazard! oil heater IDS 20 / IDS 30...
-
Page 5: Information About The Device
Wheel The sucked-in air is heated and fed back to the environment via Fuel tank cap the air outlet. Air outlet for hot air oil heater IDS 20 / IDS 30... -
Page 6: Transport And Storage
• dry and protected from frost and heat • in an upright position where it is protected from dust and direct sunlight • with a cover to protect it from invasive dust, if necessary oil heater IDS 20 / IDS 30... - Page 7 3. Secure the transport handle to the frame using the screws and nuts. Assembly of the exhaust line Warning Note that this device must not be put into operation unless there is an exhaust line mounted at the flue pipe connection! oil heater IDS 20 / IDS 30...
- Page 8 Below are some examples of good and bad exhaust gas discharge: max. 10 m oil heater IDS 20 / IDS 30...
- Page 9 ≥ Ø 120 mm / chimney – inside 150 mm min. 20 x 20 cm Chimney duct min. 1 m wall duct with elbow min. 5° The following schematic representation should be considered draught booster H-shaped when planning a chimney duct: oil heater IDS 20 / IDS 30...
- Page 10 If an accessory part is missing, please are people or animals in the same room with the device! contact the Trotec customer service or the specialist dealer • The minimum distance between walls or other objects and where you purchased the device.
-
Page 11: Operation
1. Switch the device on by setting the position of the selector switch (16) to ON (thermostat). ð To confirm the completion of the start-up process, the electronic control unit causes the reset button (18) to briefly flash in red. oil heater IDS 20 / IDS 30... - Page 12 Indication Meaning Flashing in Improperly dimensioned flame during start-up orange Flashes red Flame failure during start-up Flashing in Flame failure during operation red/green Illuminated in Internal error of an electronic controller orange oil heater IDS 20 / IDS 30...
-
Page 13: Available Accessories
Using insertion tools or accessories other than those ignition: specified in the instructions may cause a risk of injury. • This is not a fault. Air might have accumulated in the lines. Keep a safety distance to the device! oil heater IDS 20 / IDS 30... - Page 14 • Check the sealing at the drain screw and replace it if damaged. • Check the fuel pump for leaks. If there are doubts about the proper condition of the fuel pump, please contact the customer service. oil heater IDS 20 / IDS 30...
- Page 15 Magnet valve faulty Charge the customer service with the following tasks: • to have the electrical connections checked. • to have the safety thermostat L1 checked. • to have the magnet valve cleaned or replaced oil heater IDS 20 / IDS 30...
- Page 16 • to have the nozzle replaced. Device switches off; operating display Sealing of the magnet valve faulty Have the magnet valve replaced by the customer permanently illuminated in green service. oil heater IDS 20 / IDS 30...
-
Page 17: Maintenance
11. Date: ........12. Date: ........Signature: ........ Signature: ......... Signature: ......... Signature: ......... 13. Date: ......... 14. Date: ........15. Date: ........16. Date: ........Signature: ........ Signature: ......... Signature: ......... Signature: ......... oil heater IDS 20 / IDS 30... - Page 18 1. Switch the device off as described in the Shutdown chapter. 2. Wait until the device has cooled down completely. 6. Have the combustion chamber cleaned by the customer service. 7. Assemble the components in reverse order. oil heater IDS 20 / IDS 30...
-
Page 19: Technical Annex
(distance 1 m) Dimensions (length x 1050 x 400 x 1175 x 400 x width x height) 520 mm 605 mm Minimum distance to walls or other objects rear sides front Weight (with empty tank) 40 kg 48 kg oil heater IDS 20 / IDS 30... - Page 20 Wiring diagram IDS 20 / IDS 30 oil heater IDS 20 / IDS 30...
- Page 21 Overview of spare parts IDS 20 Note! The position numbers of the spare parts differ from those describing the positions of the components mentioned in these instructions. oil heater IDS 20 / IDS 30...
- Page 22 Phototransistor Flex diesel pipe El. control box panel Photoresistor support Clip Flame control box Stop button protection Filter Support plate Terminal board Flex diesel pipe Switch Air conveyor Handle Thermostat plug cover Fuse oil heater IDS 20 / IDS 30...
- Page 23 Overview of spare parts IDS 30 Note! The position numbers of the spare parts differ from those describing the positions of the components mentioned in these instructions. oil heater IDS 20 / IDS 30...
- Page 24 Air adjustment shutter Filter Power cord Diffuser ring Flex diesel pipe Lamp Fuse Handle Cable fastener nut Danfoss Pipe cap Diesel pump Cable fastener El. control box Solenoid coil Control box cover Solenoid valve body oil heater IDS 20 / IDS 30...
-
Page 25: Disposal
Manufacturer and name of the authorised representative of the technical documentation: Trotec GmbH Grebbener Straße 7, D-52525 Heinsberg Phone: +49 2452 962-400 E-mail: info@trotec.de Place and date of issue: Heinsberg, 01.10.2010 Detlef von der Lieck, Managing Director oil heater IDS 20 / IDS 30... - Page 26 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...