Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for unicraft MH 3
Summary of Contents for unicraft MH 3
- Page 1 Operating instructions Machine lift MH 3, MH 8 MH 10, MH 20 MH 3 MH 10 MH 8 MH 20...
-
Page 2: Table Of Contents
Copyright © 2018 Stürmer Maschinen GmbH, Hallstadt, 16 Spare Parts Drawings .........13 Germany. 16.1 Spare parts drawing MH 3 and MH 8 ... 13 16.2 Spare parts drawing MH 10 ......14 The contents of these operating instructions are the sole 16.3 Spare parts drawing MH 20 ...... -
Page 3: Introduction
Repair service: Fax: 0951 96555-111 E-Mail: service@stuermer-maschinen.de Internet: www.unicraft.de DANGER! Spare part orders: This combination of symbol and signal words indi- Fax: 0951 96555-119 cates an imminently dangerous situation which may E-Mail: ersatzteile@stuermer-maschinen.de... -
Page 4: Responsibility Of The Operator
Safety - The operator must obtain information about the ap- plicable occupational health and safety regulations CAUTION! and, in a risk assessment, must also determine ad- This combination of symbol and signal words indi- ditional hazards that result from the special wor- cates a possibly dangerous situation which may lead king conditions at the place of installation of the to minor or light injuries if they are not avoided. -
Page 5: Personnel Requirements
Safety 2.3 Personnel requirements Qualified personnel Due to their professional training, knowledge and experi- Qualifications ence as well as knowledge of the relevant standards and regulations, the qualified personnel are able to carry out The various tasks described in this manual place diffe- the work assigned to them and to independently recog- rent demands on the qualifications of the persons entru- nize possible dangers and to avoid hazards. -
Page 6: Personal Protective Equipment
Protective clothes are made of a tightly fitted fabric TechnicalData without the protruding parts of low tear strength. 2.6 Safety information for operating personnel Type MH 3 MH 8 Load lifting capacity No operational mode which could compromise the safety Min. Height (mm) -
Page 7: Type Plate
Transport, packaging, storage Description of the Device 4.1 Type plate Illustrations in these operating instructions may de- viate from the original. 1 Hand lever 2 Carrying handle 3 Base plate Fig. 1: Type plate machine lift MH 20 Transport, packaging, storage 5.1 Transport Check the Hydraulic machine lift on delivery for any visi- ble transportation damage. -
Page 8: Assembly
Assembly Assembly Operation DANGER! DANGER TO LIFE DUE TO FAL- Use protective gloves! LING OF THE LOAD! Falling loads can cause serious injury or death. - Overload is prohibited! Check that the load never exceeds the maximum load stated on the name- Use protective boots! plate - Never move the lifted load. -
Page 9: Operating Conditions
Care, maintenance and overhaul 10 Care, maintenance and overhaul 9.1 Operating conditions The working area must be dry, fire and explosion pro- 10.1 Care by cleaning tected and free of any corrosive or poisonous sub- stances. The Mobile scissor lift platform must not be The Hydraulic machine lift must always be kept in a used to lift or move dangerous goods such as molten, clean condition. -
Page 10: Testing The Hydraulic Machine Lift
Testing the Hydraulic machine lift 11 Testing the Hydraulic machine lift Venting After some time, or after oil has been added, air bubbles can form in the hydraulic system of the Hydraulic ma- The hydraulic machine lifter is in accordance with the chine lift and impair its function. -
Page 11: Disposal, Recycling Of Used Devices
Immediately decommission used machines in order to Product group: Unicraft® Werkstatttechnik avoid later misuse and endangering of the envi-ronment Desig nation of the Machine:MH 3, MH 8, MH 10, MH 20 or of persons. Machine type: Machine lift Step 1: Remove all environmentally hazardous fluids... -
Page 12: Spare Parts
Tips and recommendations The Item number of your device: The manufacturer's warranty will become null and void if non-permissible spare parts are being used MH 3 619 0003 MH 8 619 0008 The spare parts may be purchased with the authorised... -
Page 13: Spare Parts Drawings
In case of service, the following drawing shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorised dealer. 16.1 Spare parts drawing MH 3 and MH 8 Fig. 3: Spare parts drawing MH 3 and MH 8 MH-Series | Version 2.01... -
Page 14: Spare Parts Drawing Mh 10
Spare Parts Drawings 16.2 Spare parts drawing MH 10 Fig. 4: Spare parts drawing MH 10 MH-Series | Version 2.01... -
Page 15: Spare Parts Drawing Mh 20
Spare Parts Drawings 16.3 Spare parts drawing MH 20 Fig. 5: Spare parts drawing MH 20 MH-Series | Version 2.01... - Page 16 www.unicraft.de...