Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for unicraft PK 1
Summary of Contents for unicraft PK 1
- Page 1 Operating Instructions Mobile gantry crane PK 1 PK 1...
-
Page 2: Table Of Contents
Stuermer.Passing on as well as copying of this document, the use and distribution of its content are prohibited if not explicitly permitted. Contra- ventions are liable to compensation. Subject to technical modifications and error. PK 1 | Version 1.03... -
Page 3: Introduction
This combination of symbol and signal words indi- cates a potentially dangerous situation which may lead to death or severe injury if not avoided. PK 1 | Version 1.03... -
Page 4: Obligations Of The Operating Company
PK 1 | Version 1.03... -
Page 5: Requirements To Staff
The operating staff must always make sure that the max. Carrying capacity is not exceeded. PK 1 | Version 1.03... -
Page 6: Safety Information For Operating Personnel
They are to be replaced immediately. per and lower limbs. If the safety signs are not immediately recognizable and comprehensible, the gantry crane should be taken out of operation until new safety signs have been attached. PK 1 | Version 1.03... -
Page 7: Technical Data
Weight 128 kg 4.2 Type plate Fig. 2: Type plate Mobile gantry crane PK 1 Transport, packaging, storage 5.1 Transport Check the Mobile gantry crane on delivery for any vi- sible trans-portation damage. If you notice any damage to the device please report this immediately to the car- Fig. -
Page 8: Assembly
(1, 2, 3, 4). Step 3: Attach the four castors (27) to the trolleys (26) with the screws (15), spring washers (16) and nuts (17). Fill the bearing housings with grease over the grease nipple. PK 1 | Version 1.03... -
Page 9: Oparation
All work with the gantry crane may only be carried out by instructed persons. All parts of the gantry crane must be checked for correct condition before starting work, especially the Fig. 4: Place the trolley on the track lifting hooks of the lifting device. PK 1 | Version 1.03... - Page 10 Lift the suspension hooks (Fig. 4, 2) with the locking bolts in the lower position simulta- CAUTION DANGER OF CRUSHING! neously on both sides by pressing down the two levers for height adjustment (Fig. 4, 3). PK 1 | Version 1.03...
-
Page 11: Care, Maintenance And Repair
Step 4: Make sure that all safety instructions on the gan- try crane are clearly legible. Step 2: If required, disassemble the machine into easy- to-handle and usable components and parts. Step 3: Dispose of machine components and operating materials by the disposal channels provided. PK 1 | Version 1.03... -
Page 12: Spare Parts
- Only use original spare parts of the manufacturer or spare parts admitted by the manufacturer. - Type of device: Gantry crane PK 1 - Always contact the manufacturer in case of uncer- - Item number: 6172100 tainties. -
Page 13: Spare Parts Drawing
In case of service, the following drawing shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorised dealer. Fig. 8: Spare parts Drawing PK 1 PK 1 | Version 1.03... -
Page 14: Ec Declaration Of Conformity
Risk assessment and risk reduction DIN EN 15011:2014-09 Cranes - Bridge and gantry cranes; German version EN 15011:2011+A1:2014 Kilian Stürmer, Stürmer Maschinen GmbH, Responsible for documentation: Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 15.03.2017 ______________________ Kilian Stürmer Manager PK 1 | Version 1.03... -
Page 15: Notes
Notes 14 Notes PK 1 | Version 1.03... - Page 16 www.unicraft.de...