Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for unicraft HZ 751
Summary of Contents for unicraft HZ 751
- Page 1 Operating Instructions Lever hoist HZ 751 HZ 1501 HZ 3001 HZ 751...
-
Page 2: Table Of Contents
Content 1 Introduction ............. 3 Product identification 1.1 Copyright .............3 Lever hoist item number 1.2 Customer service..........3 1.3 Limitation of liability ..........3 HZ 751 6171175 2 Safety................ 3 HZ 1501 6171115 2.1 Symbol explanation ..........3 HZ 3001 6171130 2.2 Obligations of the operating company ....4 2.3 Requirements to staff...........5... -
Page 3: Introduction
Fax: 0049 (0) 951 96555-111 Email: service@stuermer-maschinen.de Internet: www.unicraft.de DANGER! Spare part orders: This combination of symbol and signal words indi- Fax: 0049 (0) 951 96555-119 cates an imminently dangerous situation which may Email: ersatzteile@stuermer-maschinen.de... -
Page 4: Obligations Of The Operating Company
Safety Obligations of the operating company WARNING! If the lever hoist is used for commercial purposes, the This combination of symbol and signal words indi- operating company of the lever hoist must comply with cates a potentially dangerous situation which may the legal working safety regulations. -
Page 5: Requirements To Staff
Safety 2.3 Requirements to staff 2.4 Personal protective equipment The personal protective equipment serves to protect Qualifications persons against impairments of safety and health while working. The staff member has to wear personal protec- The different tasks described in this manual represent tive equipment while performing different tasks on and different requirements to the qualification of the persons with the machine which are indicated in the individual... -
Page 6: Safety Information For Operating Personnel
Intended use It is important to point out that the making of any unau- and UVV, BGV D6 (VBG 9 April 2001) and DIN EN 818-7 thorised modifications or changes to the machine is not September 2002. permitted. A record of maintenance and inspections carried out must be entered in the crane inspection log book (e.g. -
Page 7: Technical Data
Technical Data Technical Data 4.1 Type plate Fig. 2: Type plate lever hoist HZ 751 The type plate is located on the lever and contains the Fig. 1: Drawing with dimension lines following information: - Manufacturer Type HZ 751 HZ 1501... -
Page 8: Storage
Description of the device The delivery packaging is made of cardboard, so Illustrations in these operating instructions may deviate from please dispose carefully by having it chopped up and the original. given to the recycling collection. 6.2 Safety marking on the lever hoist The film is made of polyethylene (PE) and the cushioned parts of polystyrene (PS). -
Page 9: Operation
Operation Operation NOTE! - Operating personnel must be familiar with the oper- DANGER! ation and functions of the lever hoist and the safety Danger of life by crashing the load! regulations pertaining to it. Falling loads can cause serious injury or death. - The operator is responsible for ensuring that all op- - Overload is prohibited! Check that the load never erating personnel have had the necessary training. -
Page 10: Load Lowering
Care, maintenance and repair Step 5: Pull the load chain through, open the safety latch and take down the load. NOTE! - Do not wrap the load chain around the load. Care, maintenance and repair - Load chain must not be turned in itself. - Check the location of the centre of gravity in order to prevent the load from slipping or moving. - Page 11 Care, maintenance and repair Maintenance plan Maintenance Maintenance tasks intervals Functional test: ATTENTION! - Maintenance and repair works must only be per- Set the mode-selection switch to the formed by specialists. UP and DOWN positions and check the lifting and lowering functions. Use only original spare parts in case of a repair.
- Page 12 Care, maintenance and repair Step 1: Hook the load. Model HZ 751 HZ 1501 HZ 3001 Step 2: Lift the load upwards. L max. [mm] 92,5 123,3 154,0 Step 3: Lift and lower the load to different heights. (Elongation in mm) Step 4: Check whether a secure holding of the load is ensured in every position.
- Page 13 2,5 mm. The ratchet disc has to be replaced as soon as the Model D [mm] abrasion has reached the limit listed in the following ta- ble. Standard* Limit HZ 751 12,0 HZ 1501 14,0 12,4 HZ 3001 18,0 16,1 * Nominal values.
-
Page 14: Testing Of The Lever Hoist
Model L [mm] Standard* Limit HZ 751 27 mm HZ 1501 22,5 mm HZ 3001 27 mm * The concrete value has to be measured at the new spring. -
Page 15: Trouble Shooting
Trouble shooting 11 Trouble shooting Failures Possible cause Solution Hoist doesn‘t work 1. Pawl does not engage; possibly 1. Clean and lubricate the pawl and because of pollution. ratchet. 2. Pawl spring is defect. 2. Replace pawl spring. 3. Ratchet spring is loose or dam- 3. -
Page 16: Spare Parts
13 Spare parts Example Load hooks for the lever hoist must be ordered. DANGER! - Type of device: Lever hoist HZ 751 Danger of injury by the use of wrong spare - Item number: 6171175 parts! - Position No.: 10... -
Page 17: Spare Parts Drawing
Spare parts 13.2 Spare parts drawing In case of service, the following drawing shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorised dealer. Fig. 12: Spare parts drawing HZ-Serie | Version 1.03... -
Page 18: Ec Declaration Of Conformity
According to machine directive 2006/42/EC Annex II 1.A Stürmer Maschinen GmbH Manufacturer/distributing company: Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt herewith declares that the following product Unicraft® Werkstatttechnik Product group: HZ 751 Designation of the machine: HZ 1501 HZ 3001 Lever hoist Machine type: 6171175 Item number:... -
Page 19: Maintenance Plan
Maintenance plan 15 Maintenance plan maintenance plan 40 h 40 h 40 h 200 h as re- 200 h as re- annu- quired quired ally Date Operating Employee Signature hours HZ-Serie | Version 1.03... - Page 20 www.unicraft.de...