Related Manuals for unicraft K 1001
Summary of Contents for unicraft K 1001
- Page 1 Operating Instructions Chain Hoist K 1001, K 2001, K 3001 K 5001, K 10001 Chain Hoist K 1001...
-
Page 2: Table Of Contents
Content Introduction ...............3 Product identification 1.1 Copyright ............3 Chain Hoist Item number 1.2 Customer service..........3 1.3 Limitation of liability ..........3 K 1001 6171001 2 Safety................3 K 2001 6171002 2.1 Symbol explanation ..........3 K 3001 6171003 2.2 Obligations of the operating company ....4... -
Page 3: Introduction
Introduction Introduction 1.3 Limitation of liability All information and notes in these operating instructions You have made a good choice by purchasing the UNI- were summarised while taking applicable standards CRAFT Chain Hoist. and rules, the state-of-the-art technology and our long- term knowledge and experiences into consideration. -
Page 4: Obligations Of The Operating Company
Safety Obligations of the operating company CAUTION! If the chain hoist is used for commercial purposes, the This combination of symbol and signal words indi- operating company the chain hoist must comply with the cates a potentially dangerous situation which may legal working safety regulations. -
Page 5: Requirements To Staff
Safety 2.3 Requirements to staff 2.4 Personal protective equipment The personal protective equipment serves to protect Qualifications persons against impairments of safety and health while working. The staff member has to wear personal protec- The different tasks described in this manual represent tive equipment while performing different tasks on and different requirements to the qualification of the persons with the machine which are indicated in the individual... -
Page 6: Safety Information For Operating Personnel
Intended use It is important to point out that the making of any unau- Intended use thorised modifications or changes to the machine is not permitted. The chain hoist must only be used for lifting and Operating personnel must always ensure that the maxi- lowering of machines up to the maximum specified load. -
Page 7: Technical Data
Technical Data Technical Data Dimensions 4.1 Type plate 1,0 t; 2,0 t 3,0 t; 5,0 t Fig. 1: Type plate and the safety symbols Chain Hoist K 1001 4.2 Table Type K 1001 K 2001 K 3001 Load carrying capacity (t) -
Page 8: Storage
Operation The delivery packaging is made of cardboard, so Operation please dispose carefully by having it chopped up and given to the recycling collection. DANGER! The film is made of polyethylene (PE) and the cushioned Danger of life by crashing the load! parts of polystyrene (PS). -
Page 9: Operating Conditions
Operation NOTE! Wear safety boots! - Do not wrap the load chain around the load. - The load chain must be not urned in itself. Wear protective clothing! - Check the center of gravity of the attachment point to prevent movement and slippage of the load. - Slings (eyelet, chain, etc.) must lie loosely in the hook base. -
Page 10: Care, Maintenance And Repair
Care, maintenance and repair Step 1: Lubricate all moving parts of the chain hoist Care, maintenance and repair (gears, bearings) with good quality grease. Step 2: Check the the chain hoist before each operation 7.1 Care by cleaning for visible signs of wear. The chain hoist must always be kept in a clean condition. - Page 11 Care, maintenance and repair Control of the brake system Model K 1001 K 2001, K 5001, ATTENTION! K 3001 K 10001 Standard chain link The brake dsytem must be checked regularly! Diameter D [mm] Brake-/Ratche tests areto be carried out as follows: D min.
- Page 12 Care, maintenance and repair Wear measurement and replace the pin of the load hook Wear measurement of the pin hole, replacement of the complete hook The load hook-pin must be replaced as soon as a defor- mation (see Fig. 9) can be detected and/or as soon as the wear has reached the limit value in the following ta- ble.
-
Page 13: Testing The Chain Hoist
Testing the chain hoist Disposal, recycling of used devices Please take care in your own interest and in the interest of the environment that all component parts of the ma- chine are only disposed of in the intended and permit- ted way. -
Page 14: Spare Parts
Danger of injury by the use of wrong spare wing. parts! Dangers may result for the user and damages as - Type of device: Chain Hoist K 1001 well as malfunctions may be caused by using wrong - AItem number: or damaged spare parts. -
Page 15: Spare Parts Drawing
Spare parts 10.2 Spare parts drawing In case of service, the following drawing shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorised dealer. Fig. 13: Spare parts drawing K-Series | Version 1.03... -
Page 16: Ec Declaration Of Conformity
According to machine directive 2006/42/EC Annex II 1.A Stürmer Maschinen GmbH Manufacturer/distributing company: Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt herewith declares that the following product Unicraft® Werkstatttechnik Product group: K 1001 Designation of the machine: K 2001 K 3001 K 5001 K 10001 6171001 Item number:... -
Page 17: Maintenance Plan
Maintenance plan 12 Maintenance plan Maintenance plan 40 h 40 h 40 h 200 h as nec- 200 h as nec- annu- essary essary ally date operating Employee Signature hours K-Series | Version 1.03... - Page 18 www.unicraft.de...