Page 16
Always keep this product dry. Do not use in rain or in damp conditions. This V860IIIF camera flash applies to FUJIFILM series cameras Do not disassemble. Should repairs become necessary, this and is compatible with TTL autoflash. With this TTL compatible flash, product must be sent to an authorized maintenance center.
Warning Name of Parts Body Control Panel Dot-matrix LCD Panel LCD Panel in Three Modes What's in the Box of V860IIIF Kit? Separately Sold Accessories Battery LED Modeling Lamp Attaching to a Camera Power Management Flash Mode — TTL Autoflash...
● LCD Panel Name of Parts (1)TTL Autoflash : zoom display (Page 51) Zoom : Automatic Focus length (Page 1) : Manual(Page 41) TTL : autoflash Distance indicator display Flash exposure compensation amount ● The display will only show the settings currently applied. ●...
● What’s in the Box of V860IIIF Kit? (4) Radio Transmission Shooting 1. Flash Unit 2. Lithium Battery 3. USB Battery Charger ● Transmitter Unit (TX) 4. USB Cable 5. Charger 6. Mini Stand Flash mode 7. Protection Case 8. Instruction Manual...
Battery LED Modeling Lamp ● Press the Modeling Lamp Setting button to set the modeling lamp. Features Short press the Set Button to turn on or off the modeling lamp. 1. This flash unit uses Li-ion battery which has long runtime. When turning the modeling lamp on, turn the select dial to set its The available charge-and-discharge times are 480.
C.Fn Disabling Auto Power Off function is recommended when the flash is used off camera. (C.Fn-STBY, Page 52) Receiver Auto Power Off Timer is set to 60 minutes by C.Fn default. Another option “30 minutes” is available. (C.Fn- RX STBY, Page 52) Flash Mode —...
M: Manual Flash Multi: Stroboscopic Flash The flash output is adjustable from 1/1 full power to 1/256th power With stroboscopic flash, a rapid series of flashes is fired. It can be in 1/10th stop increments. To obtain a correct flash exposure, use a used to capture a multiple images of a moving subject in a single hand-held flash meter to determine the required flash output.
Maximum Stroboscopic Flashes: Positioning and Operation Range (Example of wireless flash shooting) Flash output ● Autoflash Shooting with One Receiver Unit TRANSMITTER RECEIVER 1/16 1/32 1/64 Transmission distance is about 100m. 1/128 1/256 ● Use the supplied mini stand to position the receiver unit. Flash 20-50 60-100...
Using Automatic Wireless Flash with a Single Receiver Unit Transmitter Unit Setting Short press the <MODE> button to gain Multi mode. ● Attach a V860IIIF camera flash on the camera and set it as the transmitter unit. ● M/A/B/C can be set as TTL mode independently.
Page 25
Receiver Unit Setting Using Automatic Wireless Flash with Multiple Receiver Units ● Set the V860IIIF that to be When stronger flash output or controlled as the wireless more convenient lighting operation receiver unit. is needed, increase the number of ● The receiver unit can be receiver units and set it as a set as A/B/C/D/E.
7. M: Wireless Flash Shooting with Manual Flash The Reason & Solution of Not Triggering in Godox 2.4G Wireless This describes wireless (multiple shooting) using manual flash. You can shoot with a different flash output setting for each receiver unit 1.
Bounce Flash C.Fn: Setting Custom Functions By pointing the flash head toward a wall or ceiling, the flash will bounce off the surface before illuminating the subject. This can The following table lists the available and unavailable custom soften shadows behind the subject for a more natural-looking shot. functions of this flash.
Protection Function Technical Data Model V860IIIF 1. Over-Temperature Protection Compatible Cameras FUJIFILM cameras (TTL autoflash) ● To avoid overheating and deteriorating the flash head, there is Power (1/1 output) 76Ws over-temperature protection in the system. When continuously Guide No.(1/1 output, GN≈60 (m ISO100)
The Camera Flash does not fire. ● As the firmware upgrade needs the support of Godox G3 ● The camera flash is not attached securely to the camera. software, please download and install the "Godox G3 firmware →Attach the camera’s mounting foot securely to the camera.
Page 30
FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 31
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card.