固件升级 Foreword 本机通过USB插座可进行固件升级。软件最新公告及说明将会发布在 Thank you for purchasing this product. 官方网站上。 This V860IIC camera flash applies to Canon EOS series cameras 注:本品出厂不配USB升级线,请另行购买。普通的USB线可 使用,本产品USB口为Micro USB 接口。 and is compatible with E-TTL II autoflash. With this E-TTL II compatible flash, your shooting will become simpler. You can easily achieve a correct flash exposure even in complex light-changing environments.
● 2.4G Radio Transmission: As a Master Unit (4) Radio Transmission Shooting/Optic Transmission Shooting ● Master Unit Flash mode : Group flash (radio transmission) : Master : Radio transmission : Flash ratio RATIO wireless shooting : Optic transmission wireless shooting ●...
● Separately Sold Accessories To unload the battery, tap the white knob and the battery The product can be used in combination with the following accessories pack will pop out. Then close sold separately, so as to achieve best photography effects: the compartment.
Page 7
FEB: Flash Exposure Bracketing C.Fn Disabling Auto Power Off function is recommended You can take three flash shots while automatically changing the when the flash is used off camera. (C.Fn-APO, Page 77) flash output for each shot from -3 to +3 in 1/3rd stops. The camera Slave Auto Power Off Timer is set to 60 minutes by C.Fn will record three images with different exposures: one exposed...
Page 8
M: Manual Flash ● If the subject is too far away and underexposure, the < > icon will blink in the viewfinder. Move closer to the subject and try the FE lock again. The flash output is adjustable from 1/1 full power to 1/128th power ●...
Page 9
Maximum Stroboscopic Flashes: Multi: Stroboscopic Flash Flash output With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture a multiple images of a moving subject in a single photograph. You can set the firing frequency (number of flashes per sec. 1/16 expressed as Hz), the number of flashes, and the flash output.
Page 10
● Shooting with a Different Flash Mode set for Each Group Positioning and Operation Range (Example of wireless flash shooting) ● Autoflash Shooting with One Slave Unit Auto external flash metering Ceiling E-TTL II Transmission distance is about 100m. Manual flash Manual flash Manual flash ●...
Page 11
3. Setting the Communication Channel 1. Wireless Settings If there are other wireless flash systems nearby, you can change the You can switch between normal flash and wireless flash. For normal channel IDs to prevent signal interference. The channel IDs of the flash shooting, be sure to set the wireless setting to OFF.
Page 12
Set the master unit’s flash Using Fully Automatic Wireless Flash mode to <ETTL>. The FEC and other settings that set on the master unit will also be ● Set the master unit’s flash appeared on the slave unit automatically. The slave unit does not mode to <ETTL>.
Page 13
Setting flash ratio. ● The flash ratio of 8:1 to 1:1 to 1:8 is equivalent to 3:1 to 1:1 ● Press Function Button 3 to 1:3 (1/2 step increment). < >. ● The details of the flash ratio settings are as follows. ●...
Page 14
Set the flash mode ● Set the flash mode of each 7. Multi: Wireless Flash Shooting with Manual Flash firing group by operating the master unit. Setting <MULTI> stroboscopic flash. ● While < > is MENU1 ● Press <MODE> button so that displayed, press Function Button 3 <...
Page 15
Wireless Flash Shooting: Optic Transmission 2. Master Unit’s Flash OFF When the master unit is set to OFF, only the slave units will fire a This product supports wireless flash application and functions flash. as either a master or a slave unit. As a master unit, it can control Press Function Button 4 so Canon speedlites e.g.
Page 16
Slave Unit Setting Using Automatic Wireless Flash with Multiple Slave Units ● Set the other camera flash When stronger flash output or as the wireless slave Unit. more convenient lighting operation ● As a slave unit, V860IIC is needed, increase the number of can receive wireless signals slave units and set it as a single of Canon speedlites e.g.
Page 17
5.ETTL: Use the Wireless Shooting of Flash Ratio Auto Flash Shooting with Three Slave Unit Auto Flash Shooting with Two Slave Unit Setting the slave group <C>. Divide the slave units into A and B groups and balance their shooting ●...
Setting the number of flash Other Applications groups. ● When < > is MENU1 Wireless Control Function displayed, press the Function Button 2 The flash unit is built in with a Wireless Control Port so that you can < > to set the RATIO wirelessly adjust the power level of the flash and the flash triggering.
Bounce Flash ZOOM: Setting the Flash Coverage and Using By pointing the flash head toward a wall or ceiling, the flash will the Wide Panel bounce off the surface before illuminating the subject. This can The flash coverage can be set automatically or manually. It can be soften shadows behind the subject for a more natural-looking shot.
C.Fn: Setting Custom Functions Control with the Camera’s Menu Screen The following table lists the available and unavailable custom If the camera flash is attached to an EOS camera which has a functions of this flash. speedlite control function, the flash can be controlled using the camera’s menu screen.
Troubleshooting Firmware Upgrade If there is a problem, refer to this Troubleshooting Guide. This flash supports firmware upgrade through the USB port. Update information will be released on our official website. The Camera Flash does not fire. USB connection line is not included in this product. The USB ●...