Table of Contents
Advertisement
Quick Links
Rev .July 17, 2018
PTM-GPT Powered Trailer Mover
Receiving instructions:
After delivery, remove the packaging from the product. Inspect the product closely to determine
whether it sustained damage during transport. If damage is discovered, record a complete description of it
on the bill of lading. If the product is undamaged, discard the packaging.
NOTE:
The end-user is solely responsible for confirming that product design, use, and maintenance comply
with laws, regulations, codes, and mandatory standards applied where the product is used.
Replacement Parts and Technical Assistance:
If you have questions that are not addressed in these instructions and to order replacement parts,
labels, and accessories, call (260) 665-7586 and ask for the Service and Parts Department. The
department can also be contacted online at http://www.vestilmfg.com/parts_info.htm.
Specifications....................................................................................................................................... 2
Signal Words......................................................................................................................................... 2
Safe Use Recommendations..................................................................................................................... 2 - 3
Operation............................................................................................................................................ 3
Hitch Assembly Controls......................................................................................................... 4
Using the Hitch..................................................................................................................... 4
Parking Brake....................................................................................................................................... 5
Manual Mode....................................................................................................................... 5
Inspections and Maintenance.................................................................................................. 5 - 6
FIG. 1: Complete Exploded View.............................................................................................. 7 - 8
FIG. 2: Power Unit Exploded View............................................................................................ 9
FIG. 3: Sprocket Drive (Right Side) Exploded View...................................................................... 10
FIG. 4: Sprocket Drive (Left Side) Exploded View........................................................................ 11
FIG. 5: Handle Assembly Exploded View................................................................................... 12
Labeling Diagram.................................................................................................................. 13
Limited Warranty.................................................................................................................. 14
Vestil Manufacturing Corp.
2999 North Wayne Street, P.O. Box 507, Angola, IN 46703
Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868
http://www.vestilmfg.com/
Instruction Manual
Table of Contents
Fax: (260) 665-1339
e-mail:
info@vestil.com
Copyright 2018 Vestil Manufacturing Co.
PTM-GPT, MANUAL
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vestil PTM-GPT
Summary of Contents for Vestil PTM-GPT
-
Page 1: Table Of Contents
Fax: (260) 665-1339 http://www.vestilmfg.com/ e-mail: info@vestil.com PTM-GPT Powered Trailer Mover Instruction Manual Receiving instructions: After delivery, remove the packaging from the product. Inspect the product closely to determine whether it sustained damage during transport. If damage is discovered, record a complete description of it on the bill of lading. -
Page 2: Specifications
SAFE USE RECOMMENDATIONS: Vestil strives to identify all foreseeable hazards associated with the use of its products. However, material handling is dangerous and no manual can address every risk. Ultimately the most effective way to prevent injury is for the operator to apply sound judgment whenever using this device. -
Page 3: Operation
DO NOT use a ball that is too small for the trailer. DO NOT modify the mover in any way without express, written approval from Vestil. Unapproved modifications automatically void the Limited Warranty (see p. 14) and might make the product unsafe to use. -
Page 4: Hitch Assembly Controls
11. To disconnect the trailer from the mover, unlock the hitch. Then, lower the hitch assembly by pressing down the hitch control lever until the ball hitch is completed disengaged from the tongue of the trailer. Page 4 of 14 Copyright 2018 Vestil Manufacturing Co. -
Page 5: Parking Brake
Adjust the chains by applying pressure to the hex head with a wrench while loosening the lock nut. Page 5 of 14 Copyright 2018 Vestil Manufacturing Co. - Page 6 5. Before each use make sure all labels are in place & in readable condition (see “Labeling diagram” on p. 13). 6. Periodically clean dirt and debris from all surfaces of the cart to keep the finish in good condition. Store the unit indoors. Page 6 of 14 Copyright 2018 Vestil Manufacturing Co.
- Page 7 ” hex nut, gr. A, zinc plated ” external retaining ring, 50-024-001 Cover, rear leg 68015 phosphate 03-612-002 Assembly, hinge pin 01-118-001 Bolt, cylinder retaining Parts list continues on page 8 Page 7 of 14 Copyright 2018 Vestil Manufacturing Co.
- Page 8 •• Item 6 shown in exploded view in FIG. 3 ••• Item 7 shown in exploded view in FIG.4 * Items 45-73 comprise the power unit subassembly shown in FIG. 2. Page 8 of 14 Copyright 2018 Vestil Manufacturing Co.
- Page 9 99-031-096 Accessories, clamp, 2 ear, 1 ” down 50-623-002 Subassembly, hose, feed 99-031-095 Accessories, clamp, 2 ear, 1 ” Fitting, hydraulic, 06MJ-08MP 50-623-003 Subassembly, hose, return 99-116-060 straight 50-623-004 Subassembly, hose, suction Page 9 of 14 Copyright 2018 Vestil Manufacturing Co.
- Page 10 ” thread cutting screw, slotted, type F, z-plated 11053 ”-18x ” bolt, HHCS, #2, z-plated 16 50-120-005 Nut, front lug nut 36104 ”-18 hex nut, gr. A, z-plated 18 99-130-002 Pin, keystock Page 10 of 14 Copyright 2018 Vestil Manufacturing Co.
- Page 11 32416 ”-18x ” thread cutting screw, slotted, type F, z-plated 11053 ”-18x ” bolt, HHCS, #2, z-plated 36104 ”-18 hex nut, gr. A, z-plated 99-130-002 Pin, keystock 99-130-003 Pin, key stock Page 11 of 14 Copyright 2018 Vestil Manufacturing Co.
- Page 12 ”-16 Nylon insert lock nut, gr. 2, zinc 50-120- 37024 Nut, brake nut finish Switch, pushbutton SPST, normally 50-022- Switch pushbutton SPST, normally 50-022-001 closed open 50-017- 50-024-003 Cover, switch cover Spacer, lower handle spacer Page 12 of 14 Copyright 2018 Vestil Manufacturing Co.
-
Page 13: Labeling Diagram
Parts Department. A: Label 287 B: Label 206 C: Label 208 D: Label 661 E: Label 835 F: Label 834 G: Label 662 H: Label 1060 L: Label 696 J: Label 220 Page 13 of 14 Copyright 2018 Vestil Manufacturing Co. -
Page 14: Limited Warranty
Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent allowed by law. Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty. Vestil makes no warranty or representation that this product complies with any state or local design, performance, or safety code or standard.
Need help?
Do you have a question about the PTM-GPT and is the answer not in the manual?
Questions and answers