Table of Contents
Advertisement
User Manual
Motor Control For Height Adjustable Desks
CBX-1 / CBX-2
LOGICDATA Electronics & Software Development GmbH
Hinterleitenstrasse 22a
A 8523 Frauental /Austria
Version: GER11-170904
Availability and specifications are subject to change without prior notice. LOGICDATA assumes no
liability for maloperation or improper use of products. LOGICDATA will at point of delivery
replace/repair defective products covered by the warranty. No liability is assumed beyond such
replacement/repair. Please contact LOGICDATA directly on inquiries or custom requirements.
2004 LOGICDATA
Advertisement
Table of Contents
Related Manuals for LOGICDATA CBX-1
Summary of Contents for LOGICDATA CBX-1
- Page 1 Availability and specifications are subject to change without prior notice. LOGICDATA assumes no liability for maloperation or improper use of products. LOGICDATA will at point of delivery replace/repair defective products covered by the warranty. No liability is assumed beyond such replacement/repair.
-
Page 2: Table Of Contents
User Manual CBX-1 / CBX-2 Contents Preface..........................3 1.1. Appropriate Operation....................3 1.2. Functionality CBX-1 / CBX-2 ................... 3 1.3. Performance Differences CBX-1 / CBX-2..............4 1.4. Audience and Previous Knowledge ................4 1.5. Safety Instruction Symbols ..................5 1.6. -
Page 3: Preface
CBX-1 / CBX-2 1. Preface Dear customer, Thank you for choosing a CBX-1 / CBX-2 motor control box for height adjustable desks from LOGICDATA GmbH. . You have purchased a state-of-the-art product which complies with all safety requirements. 1.1. Appropriate Operation CBX-1 / CBX-2 motor control boxes must solely be used for the intended application of control of height-adjustable desks. -
Page 4: Performance Differences Cbx-1 / Cbx-2
CBX-1 / CBX-2 1.3. Performance Differences CBX-1 / CBX-2 CBX-1 The motor control box CBX-1 is suitable to control 1 motor for desk height adjustment. CBX-2 The motor control box CBX-2 is suitable to control up to 2 motors for desk height adjustment. -
Page 5: Safety Instruction Symbols
User Manual CBX-1 / CBX-2 1.5. Safety Instruction Symbols This manual contains safety advice with symbols to point out possible dangers. The used symbols have the following meaning: Danger: This safety instruction warns of imminent danger for life and health of individuals! -
Page 6: Package Contents
User Manual CBX-1 / CBX-2 1.6. Package Contents The CBX control box package contains: Fig. 1 - Package Contents • CBX motor control box with integrated mounting link and integrated power cord. Note: For detailed information on optional control components and accessories, see page 29! 1.7. -
Page 7: Safety Instructions
User Manual CBX-1 / CBX-2 1.8. Safety Instructions This user manual contains safety instructions to point out possible dangers and therefore allow a safe operation of the CBX control box. Please consider these safety instructions unconditionally! Within this chapter you will find general safety instructions, which do not refer to a particular procedure. -
Page 8: Important Service Note
User Manual CBX-1 / CBX-2 Danger: To prevent fire or shock hazard, do not expose this device to rain or moisture! Danger: When operating the motor drive take care not to pinch individuals or objects! Even with activated protection systems a certain... -
Page 9: Mounting Instructions Cbx
User Manual CBX-1 / CBX-2 2. Mounting Instructions CBX Mount the CBX motor control on the bottom surface of the desk top. Following tools are needed for installation: • 1 screw driver for recessed head screws • 1 pencil • 1 drill machine(to pre-drill the holes) -
Page 10: Initial Operation
Danger: The initial operation of the control box must be carried out by qualified personnel only! 3.1 CBX Interfaces The motor control box CBX (CBX-1 is capable of driving 1 motor) is equipped with following interfaces: Fig.3 - Interfaces Interface to handset (HS) -
Page 11: Initial Operation Procedure
Note: When connecting, strictly stick to the sequence M1, M2! 3.2.1.2. Connect Handset Connect the handset to the 7-pin DIN socket (HS). Note: You may use various LOGICDATA handsets with th CBX control box! For detailed information refer to chapter „Optional Products“ (page xx). -
Page 12: System Configuration (Example)
User Manual CBX-1 / CBX-2 3.2.2. System Configuration (Example) The following figure illustrates the interface connections of an example configuration. This example configuration consists of: 1 CBX control box 2 Motor drives (hidden in the table-legs) Handset HSU-MDF-4M2-LD Fig.4 – Example Configuration... -
Page 13: Operation Of The Cbx Control Box
User Manual CBX-1 / CBX-2 4. Operation of the CBX control box To ensure safe operation of the CBX control box, observe following safety instructions: Caution: Keep children away from height-adjustable desks, control boxes and handsets! Risk of electric shock may be present. -
Page 14: Advanced Functionality
User Manual CBX-1 / CBX-2 4.2 Advanced Functionality Note: Functionality described in this chapter is only accessible if you have a handset with position keys and a save key! 4.2.1. Saving a Position This function allows to save one desk-height per position key. To save a desk... -
Page 15: Moving To A Saved Position
User Manual CBX-1 / CBX-2 4.2.2. Moving to a Saved Position This function allows to move the desk to a saved position. To move to a saved position, proceed as follows: Note: Whether the double-click automatic function is available or not, depends on the software configuration of the control box. -
Page 16: Change Displayed Height
User Manual CBX-1 / CBX-2 4.2.3. Change Displayed Height This function allows you to change the displayed height, you cannot change the desk-height. Proceed as follows: Press the S key. The display reads S –. Press and hold key desk down (arrow downwards) for appr. 5 seconds. -
Page 17: Activation Of The End Position Alignment Procedure
User Manual CBX-1 / CBX-2 4.2.5. Activation of the End Position Alignment Procedure Activating the end position alignment procedure lies within the scope of initial operation carried out by a service technician. Press and hold keys desk up and desk down (or alternatively the S key) simultaneously for about 5 seconds until the control box clicks once. -
Page 18: Software-Dependent Functions
User Manual CBX-1 / CBX-2 4.3 Software-dependent Functions Note: Prior to delivery, the CBX control box is being parameterized. Following functions are only available if the control box is parameterized accordingly. 4.3.1. Reset after Power On After each power-on (e.g. connecting the power cord) following reset procedure is... -
Page 19: Drive Back
User Manual CBX-1 / CBX-2 4.3.4. Drive Back Note: The drive back function is only active when the optional module (ACS-CB-PINCH) and squeeze line are connnected. For detailed information refer to page 4.4! After the pinch protection function has triggered (squeeze line), the desk automatically moves in the opposite direction for a pre-defined distance. -
Page 20: Pinch Protection Module Acs-Cb-Pinch
4.4 Pinch Protection Module ACS-CB-PINCH The ACS-CB-PINCH module is required to be able to connect a squeeze line to LOGICDATA control boxes that are not equipped with the corresponding interface (CBX, CBS, CBB). Note: The ACS-CB-PINCH module is not part of the standard scope of... -
Page 21: Acs-Cb-Pinch Mounting And Connection
User Manual CBX-1 / CBX-2 4.4.2. ACS-CB-PINCH mounting and connection Caution: Unplug the power cord when connecting the ACS-CB-PINCH module! To install and connect the ACS-CB-PINCH module, proceed as follows: 1. Connect the short cable (interface ) to the desired interface of the control box (M1 or M2). -
Page 22: Technical Data
User Manual CBX-1 / CBX-2 5. Technical Data General 110V ±6% / 60 Hz Supply Voltage Standby-Consumption primary 1,1 W Operating Voltage Electronics 5VDC ±5% 150mA 5VDC ±10% 150mA Hall Sensor Operating Voltage Ambient Temperature 0 - 35°C Operation Humidity 5 –... - Page 23 User Manual CBX-1 / CBX-2 Type Label The following figure shows the type label and its location on the control box housing. Note: Specifications on the type label are dependent on the version of the CBX control box (see technical data).
-
Page 24: Appendix
User Manual CBX-1 / CBX-2 6. Appendix This chapter offers detailed information on the following topics: • Possible troubles and solutions • Displayed error messages • Optional products (squeeze line and handsets) 6.1 Possible Troubles and Solutions Drives do not work... -
Page 25: Displayed Error Messages
User Manual CBX-1 / CBX-2 6.2 Displayed Error Messages Note: Error messages will only be displayed on handsets with a display! The display reads HOT. Cause Solution The CBX control box is equipped with Wait until the control box has cooled duty cycle monitoring. -
Page 26: Optional Accessories
User Manual CBX-1 / CBX-2 6.3 Optional Accessories Following optional accessories are available for CBX controls. Note: Parts of the functionality of the CBX control box are only accessible if you have optional accessories installed! Squeeze Line The squeeze line has to be fixed to the bottom side of the desk-top. When the squeeze line is pinched (e.g. - Page 27 User Manual CBX-1 / CBX-2 Handset LOGICDATA offers a broad range of handsets with diverse functionality. Following handsets are compatible with the LogicS series of control boxes: Note: For detailed information about LOGICDATA handsets, see the separately available product catalog.
- Page 28 User Manual CBX-1 / CBX-2 Foil handset • Large keys • Outstanding adhesive properties • Durable ACS-ADAP-MOUSE PC-mouse-adapter • Desk movement via PC-mouse • No software required • Even works without PC • Suitable for all types of mouse IRR-DSK-SET-LIGHT Infrared handset „Standard“...
-
Page 29: Continuative Information
User Manual CBX-1 / CBX-2 Handset with display and memory function. • 5 memory keys • 2 UP/DOWN keys • Display • Silver syling • Soft-Touch keys 7. Continuative Information 7.1 Final Disposal Consider following disposal instructions when disposing of the CBX control box:...