Table of Contents
Related Manuals for LOGICDATA SMARTneo-2G
Summary of Contents for LOGICDATA SMARTneo-2G
- Page 1 MANUAL Document Version 1.0 /July 2019 SMARTneo-2G Cascading...
- Page 2 The German language version is the original LOGICDATA Electronic & Software Entwicklungs GmbH Wirtschaftspark 18 8530 Deutschlandsberg Austria Phone: +43 (0) 3462 51 98 0 Fax: +43 (0) 3462 51 98 1030 Internet: http://www.logicdata.net Email: office.at@logicdata.net INFO This manual is valid for SMARTneo-2G Control Boxes.
-
Page 3: Quick Reference
SMARTNEO-2G: CASCADING MANUAL // PAGE 3 QUICK REFERENCE The Quick Reference is not a substitute for the product documentation. For your own INFO safety, read the complete product documentation before connecting the components to form a Cascading System and putting it into operation. - Page 4 SMARTNEO-2G: CASCADING MANUAL // PAGE 4 Cascading System with 2 Actuators For detailed instructions, see chapter 6.3.5 on page 15 Cascading System with 3 Actuators For detailed instructions, see chapter 6.6 on page 16...
- Page 5 SMARTNEO-2G: CASCADING MANUAL // PAGE 5 Cascading System with 4 Actuators For detailed instructions, see chapter 6.7 on page 17 Performing the Reference Drive For detailed instructions, see chapter 7.1 on page 18 CLICK Factory Reset For detailed instructions, see chapter 7.2 on page 18 Comfort: 3 s...
-
Page 6: Table Of Contents
SMARTNEO-2G: CASCADING MANUAL // PAGE 6 CONTENTS Quick reference General information Other applicable documents Copyright Royalty-free use of images and text Trademarks Safety Target audience General safety regulations Intended use Reasonably Foreseeable Misuse Explanation of symbols and signal words Liability... - Page 7 SMARTNEO-2G: CASCADING MANUAL // PAGE 7 Cascading System with three Actuators 6.6.1 Required Components 6.6.2 Connecting the Components Cascading System with four Actuators 6.7.1 Required Components 6.7.2 Connecting the Components Operation Reference Drive Factory Reset 7.2.1 With a Basic Hand Control 7.2.2 With a Comfort Hand Control...
-
Page 8: General Information
The license does not include logos, designs, and page layout ele- ments belonging to LOGICDATA. The customer may make any necessary changes to the text and images to adapt them for the purpose of end user documentation. Texts and images may not be sold in their current state, and may not be published or sublicensed digitally. -
Page 9: Safety
3.3 INTENDED USE The SMARTneo-2G is a Control Box for electrically Height-Adjustable Tables. It is intended for indoor use only. The system may only be installed in compatible Height-Adjustable Tables and with LOGICDATA- approved accessories, including those intended to enable Cascading functionality. -
Page 10: Explanation Of Symbols And Signal Words
Indicates important tips for handling the product. 3.6 LIABILITY LOGICDATA products comply with all currently applicable health and safety regulations. However, risk can result from incorrect operation or misuse. LOGICDATA is not liable for damage or injury caused by: • Improper product use •... -
Page 11: Residual Risks
Cascading System are listed in this Manual. The risks associated with the installation of other prod- ucts in the system, including the SMARTneo-2G, are detailed in the respective product’s Operating Manual. See also Chapter 2.1. The symbols and signal words used in this Operating Manual are listed in Chapter 3.5. -
Page 12: Skilled Persons
3.9 NOTES FOR RESELLERS Resellers are companies that purchase LOGICDATA products for installation in their own products. For reasons of EU conformity and product safety, Resellers should provide end users INFO with an Operating Manual in their native EU official language. -
Page 13: Product
5 PRODUCT ABOUT CASCADING Cascading is the process of connecting two SMARTneo-2G Control Boxes together in order to control extra Actuators. A maximum of 4 Actuators can be connected. Each Actuator must be of the same type. In Cascading Systems, the two Control Boxes are connected by a Sync Cable (LOG-CBL-SMARTneo- SYNC-1000). -
Page 14: Connecting The System
SMARTNEO-2G: CASCADING MANUAL // PAGE 14 6 CONNECTING THE SYSTEM The SMARTneo-2G can be used to create a variety of Table Systems. This Manual describes the connection of table systems in which two Control Boxes will be connected. This chapter describes the process of connecting the Cascading System’s components after they have been mounted to the Height-Adjustable Table System. -
Page 15: Cascading System With Two Actuators
SMARTNEO-2G: CASCADING MANUAL // PAGE 15 6.5 CASCADING SYSTEM WITH TWO ACTUATORS When a Hand Control is connected to a Cascading System for the first time, the INFO Control Box it is connected to becomes the master. The other Control Box is the slave. -
Page 16: Cascading System With Three Actuators
SMARTNEO-2G: CASCADING MANUAL // PAGE 16 6.6 CASCADING SYSTEM WITH THREE ACTUATORS When a Hand Control is connected to a Cascading System for the first time, the INFO Control Box it is connected to becomes the master. The other Control Box is the slave. -
Page 17: Cascading System With Four Actuators
SMARTNEO-2G: CASCADING MANUAL // PAGE 17 6.7 CASCADING SYSTEM WITH FOUR ACTUATORS When a Hand Control is connected to a Cascading System for the first time, the INFO Control Box it is connected to becomes the master. The other Control Box is the slave. -
Page 18: Operation
7.2 FACTORY RESET (S0 RESET) With this function, you can reset the SMARTneo-2G to its factory settings. No Factory Reset is required before setup. Factory Resets are required after changes in the setup of Cascading System and to reset the Slave-Master hierachy in the system (e.g. -
Page 19: With A Comfort Hand Control
SAVE Press the SAVE Key. The SMARTneo-2G has now been reset to its factory settings. It is now in the same state as it was during the first start-up. Resetting the Master Control Box in the system to factory settings will automatically INFO reset the Slave Control Box. -
Page 20: Troubleshooting
The Control Box is Contact customer services defective For further information, or if you are experiencing problems that are not covered in this chapter, refer to the operating manual of the Hand Control and the operating manual of the SMARTneo-2G Control Box. -
Page 21: Additional Information
9.2.1 DISPOSAL The SMARTneo-2G is an electrical and electronic device that must be disposed of separately from household trash in accordance with the WEEE directive 2012/19/EU. Products of this type are labelled with the symbol shown on the left. - Page 22 LOGICDATA LOGICDATA North America, Inc. Electronic & Software Entwicklungs GmbH 1525 Gezon Parkway SW, Suite C Wirtschaftspark 18 Grand Rapids, MI 49509 8530 Deutschlandsberg Austria Phone: +43 (0)3462 5198 0 Phone: +1 (616) 328 8841 Fax: +43 (0)3462 5198 1030 Email: office.na@logicdata.net...
Need help?
Do you have a question about the SMARTneo-2G and is the answer not in the manual?
Questions and answers