Huvema HU 30K Vario Topline Manual
  1. Manuals
  2. Brands
  3. Huvema Manuals
  4. Drill
  5. Hu 30 K
  6. Manual

Huvema HU 30K Vario Topline Manual

Column drilling machines
Hide thumbs Also See for HU 30K Vario Topline:
Table of Contents

Advertisement

Quick Links

Download this manual
C O L U M N D R I L L I N G M A C H I N E S
HU 30K VARIO TOPLINE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HU 30K Vario Topline and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Huvema HU 30K Vario Topline

Summary of Contents for Huvema HU 30K Vario Topline

  • Page 1 C O L U M N D R I L L I N G M A C H I N E S HU 30K VARIO TOPLINE...

  • Page 2: Table Of Contents

    able of conTenTs General safety rules for all machines Additional safety rules Instructions for using this machine Specifications Unpacking Adjustment Table adjustment Depth adjustment Speed adjustment Use of the machine Placing the drill head Placing the drill Tool ejector Placing the work piece Using a machine vise Safety switch v-belt cover Tapping...

  • Page 3: General Safety Rules For All Machines

    hu 30K V olumn drilling machine ario opline eneral safeTy rules for all machines N.B.: Read the instructions carefully in order to avoid any problems. As with all machinery there are certain hazards involved with operation and use of this machine. Using the machine with respect and caution will considerably lessen the possibility op personal injury.

  • Page 4: Additional Safety Rules

    ddiTional safeTy rules Always keep in mind that: • the machine must be switched off and disconnected from the power supply during maintenance and repairs, • clamped workpieces may only be measured when the machine is switched off. Never lean over the machine, mind loose clothing, ties, jewellery etc. and wear a cap. Do not remove safety devices or guards.

  • Page 5: Unpacking

    npacKing Unpack the box and check for the parts below: Main parts Number Head Column with flange 1 Bracket Table Base Note: If you find any parts missing or damaged, please contact your dealer. Note: Clean the cone and taper of the drill head with a clean cloth before using the machine.

  • Page 6: Depth Adjustment

    epTh adjusTmenT The depth adjustment can be found at the right-hand side of the machine, at the feed handles. Loosen the clamp and set the scale to the desired position. The depth adjustment has two rings with cams. These ensure that the spindle starts to run and comes back up when the desired depth has been reached.

  • Page 7: Use Of The Machine

    se of The machine lacing The drill head See figure 7 • First insert the arbor into the spindle. Adjust the table height to about 25 mm from the arbor. Turn the feed handles to push the arbor in. • Insert the drill head into the arbor.

  • Page 8: Tapping

    Tapping Tapping can be done as follows: • Turn the switch for drilling and tapping in the ‘TAPP’ position. • Set the depth with the depth adjustment on the right-hand side of the machine (see also 5.2). • Turn the switch for high or low speed to ‘OFF’ . •...

  • Page 9: Maintenance

    ainTenance Warning! Switch the machine off and unplug it from the power supply before carrying out any maintenance or repairs! • Frequently blow out any dust that may accumulate inside the motor. • Apply a light coat of car wax to the table and column to keep the surfaces clean. •...

  • Page 10: Grounding

    • Check the tension of the machine and the power source before connecting. They should match. • Always shut down the machine after using it and pull the plug from the socket. Never pull the cable to remove the plug, this will lead to damage to the cable with a possible shortcut as a result. 10.1 g rounding •...

  • Page 11: Parts Drawings And List

    11. p arTs drawings and lisT Figure 11 CHANGES AND T YPING ERRORS RESER VED...
  • Page 12 Figure 11-1 Figure 11-2 CHANGES AND T YPING ERRORS RESER VED...
  • Page 13 No. Description Q´ty. Description Q`ty. Base Spindle pulley Column flange Lock washer Hex head bolt Screw Column Bracket Table Cable guide Gear shaft Worm gear Worm gear Switch insert Handle Screw Handle grip Head cover Hex. head screw Hex. socket set screw Lock screw Handle Hex.
  • Page 14 Washer Chuck key Motor pulley Hex. socket set screw Switch panel Locating sleeve Selector switch Motor Emergency stop Lock washer Selector switch Reversal switch turning direction Connecting line Speed knob Wire protector Stop button Screw Start button Cover KJD18 Master switch Screw Hex.
  • Page 15 All rights reserved. No part of this booklet may be reproduced in any form, by print, photoprint, microfilm or any other means without written permission from the publisher. © Huberts/Huvema BV, Kennedylaan 14, Veghel, the Netherlands. Internet: www.huvema.nl CHANGES AND T YPING ERRORS RESER VED...

Table of Contents