Advertisement

D R I L L I N G
M
M A C H I N E S
HU 25 T

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HU 25 T and is the answer not in the manual?

Questions and answers

Summary of Contents for Huvema HU 25 T

  • Page 1 D R I L L I N G M A C H I N E S HU 25 T...
  • Page 2: Table Of Contents

    able of conTenTs General safety rules for all machines Main specifications and features Several usage regulations Main specifications & parameters Parts drawings and list Structure and adjustment Transmission system Operation Lubrication Transportation and installation Electric system Accessories CHANGES AND T YPING ERRORS RESER VED...
  • Page 3: General Safety Rules For All Machines

    25 T rilling machine 1. g eneral safeTy rUles for all machines N.B.: Read the instructions carefully in order to avoid any problems. As with all machinery there are certain hazards involved with operation and use of this machine. Using the machine with respect and caution will considerably lessen the possibility op personal injury.
  • Page 4: Main Specifications And Features

    Additional safety rules Always keep in mind that: • the machine must be switched off and disconnected from the power supply during maintenance and repairs, • clamped workpieces may only be measured when the machine is switched off. Never lean over the machine, mind loose clothing, ties, jewellery etc. and wear a cap. Do not remove safety devices or guards.
  • Page 5: Parts Drawings And List

    5. p arTs Drawings anD lisT CHANGES AND T YPING ERRORS RESER VED...
  • Page 6 Figure 4 Figure 5 CHANGES AND T YPING ERRORS RESER VED...
  • Page 7 Figure 6 Figure 7 CHANGES AND T YPING ERRORS RESER VED...
  • Page 8 No. Description Description Bottom base Spindle box Spring washer Fasten bolt Hex nut Round head fasten screw Hose connector Hex nut Cover plate Cover nut Round head screw Round head nut Vertical column Cover plate Flexible metal pipe Sink screw Lift gear rack Sink screw Vertical column top cover...
  • Page 9: Structure And Adjustment

    Handle Center shaft Sleeve fasten ring Sleeve Bearing 7206 Connect sheet Bearing cover Gear z33 O shape seal Inner gear sheet Oil cup Connector Taper head fasten screw Fixture sleeve Gear z51 Sleeve Worm gear z28 Bearing 3056203 Sleeve Gear z42 Small shaft Fixture ring Gear z17...
  • Page 10: Lubrication

    9. l UbricaTion The spindle sleeve lubrication uses precision machine tool grease No. 2, change it every 1 year, The spindle box handle should be oiled every shift using No. 30 oil. 10. T ransporTaTion anD insTallaTion Before lifting the machine for transportation, the spindle box must be fastened first. The machine can be installed on any hard place, it can also be tightened by bolts.
  • Page 11: Accessories

    Power supply Figure 9 The circuit diagram is shown as Fig. 8, the electric connection is shown as Fig. 9. The machine uses 3 phase, 50Hz or 60Hz, 220V, 380V, 420V power supply, which are user selectable. The double-speed motor rotates at 1400/2800 rpm for 50Hz and 1680/3360 rpm for 60Hz, the motor power is 550/750W, the two speeds are selected by SA switch, the reverse direction can also be selected, the start and stop are realised by push button QS.
  • Page 12 CHANGES AND T YPING ERRORS RESER VED...
  • Page 13 CHANGES AND T YPING ERRORS RESER VED...
  • Page 14 All rights reserved. No part of this booklet may be reproduced in any form, by print, photoprint, microfilm or any other means without written permission from the publisher. © Huberts bv, Kennedylaan 14, Veghel, the Netherlands. Internet: www.huvema.nl CHANGES AND T YPING ERRORS RESER VED...
  • Page 15: Ce Declaration Of Conformity

    (in accordance with supplement II A of the Machinery Directive) Industrie & Handelsonderneming Huberts bv, Kennedylaan 14, 5466 AA Veghel, the Netherlands, in the capacity of importer, is to be held responsible for declaring that the Huvema machine: Drilling machine HU 25 T...

Table of Contents