Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Huvema HU 18K-2 TOPLINE
Summary of Contents for Huvema HU 18K-2 TOPLINE
- Page 1 C O L U M N D R I L L I N G M A C H I N E S HU 18K-2 TOPLINE HU 18K-4 TOPLINE...
- Page 2 Fig. A - Main parts Fig. 1 Fig. 3 Fig. 2 CHANGES AND T YPING ERRORS RESER VED CHANGES AND T YPING ERRORS RESER VED...
- Page 3 Fig. 4 Fig. 5 Fig. 7 Fig. 6 Fig. 8 Fig. 9 CHANGES AND T YPING ERRORS RESER VED...
- Page 4 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 15 Fig. 14 CHANGES AND T YPING ERRORS RESER VED CHANGES AND T YPING ERRORS RESER VED...
- Page 5 Fig. 15A Fig. 15B Fig. 16 Fig. 18 Fig. 17 CHANGES AND T YPING ERRORS RESER VED...
- Page 6 Fig. 19 Fig. 20 CHANGES AND T YPING ERRORS RESER VED CHANGES AND T YPING ERRORS RESER VED...
-
Page 7: Table Of Contents
able of conTenTs General safety rules for all machines Additional safety rules Instructions for using this machine Unpacking Assembly Adjustment 5.1 Table adjustment 5.2 Feed depth adjustment 5.3. Speed adjustment 5.4 Belt tension adjustment 5.5 Quill spring adjustment Usage 6.1 Installing drills 6.2 Positioning the work piece 6.3 Using the vice Troubleshooting... -
Page 8: General Safety Rules For All Machines
hu 18K-2 T /hu 18K-4 T olumn drilling machines opline opline 1. g eneral safeTy rules for all machines N.B.: Read the instructions carefully in order to avoid any problems. As with all machinery there are certain hazards involved with operation and use of this machine. Using the machine with respect and caution will considerably lessen the possibility op personal injury. -
Page 9: Additional Safety Rules
ddiTional safeTy rules Always keep in mind that: • the machine must be switched off and disconnected from the power supply during maintenance and repairs, • clamped workpieces may only be measured when the machine is switched off. Never lean over the machine, mind loose clothing, ties, jewellery etc. and wear a cap. Do not remove safety devices or guards. -
Page 10: Assembly
4. a ssembly • Place the column on the base and align the holes in the column support with the holes in the base (fig. 1). • Secure the column with the bolts and washers. • Take off the collar and the rack. (fig. 2) •... -
Page 11: Belt Tension Adjustment
5.4 b elT Tension adjusTmenT For proper belt tension: Use a light pressure on the V-belt. The distance should be ± 10%. 5.5 Q uill spring adjusTmenT Figure 16 • Pull the knob towards you and move it to the next or previous notch. •... -
Page 12: Maintenance
8. m ainTenance Warning! Turn the machine off and disconnect it from the mains before maintenance or repairs are performed! • Frequently blow out any dust that may accumulate inside the motor. • Apply a light coat of car wax to the table and column to keep the surfaces clean. •... -
Page 13: Parts List
10. p arTs lisT 111113 112 101-1 101-3 Fig. B - Explosion drawing CHANGES AND T YPING ERRORS RESER VED... - Page 14 Description Description Base Motor pulley Flange Screw Spring washer Bolt Spindle pulley Rack Knob Bracket Drive shaft Worm Crank sleeve handle Screw Screw Circlip Gear shaft Bearing Gear Belt Rack collar Spacer bearing Bearing Pinion shaft Circlip Bolt Screw Scale Switch Spring Power cord...
- Page 15 (in accordance with supplement II, section 1A of the Machinery Directive) Industrie & Handelsonderneming Huberts bv, Kennedylaan 14, 5466 AA Veghel, the Netherlands, in the capacity of importer, is to be held responsible for declaring that the Huvema machines: Column drilling machines HU 18K-2 Topline / HU 18K-4 Topline...
- Page 16 CHANGES AND T YPING ERRORS RESER VED CHANGES AND T YPING ERRORS RESER VED...
- Page 17 CHANGES AND T YPING ERRORS RESER VED...
- Page 18 CHANGES AND T YPING ERRORS RESER VED CHANGES AND T YPING ERRORS RESER VED...
- Page 19 CHANGES AND T YPING ERRORS RESER VED...
Need help?
Do you have a question about the HU 18K-2 TOPLINE and is the answer not in the manual?
Questions and answers