Chicco New Zenith 0+1 Instructions Manual page 31

Before fi tting the child car seat into the car, it
is necessary to adjust the height of the safety
harness correctly. The correct height of the
safety harness is slightly below shoulder level
(diag. 5). The height of the child car seat can
be adjusted to 4-positions.
The child car seat has a headhugger to ensure
maximum protection and comfort for children,
from birth up to 6 Kg of weight (diag. 6).
Before fi tting the headhugger, check that the
safety harness is inserted into the hole located
in the lowest position: this is the only position
allowed for the use of this accessory.
WARNING: To ensure maximum safety for
your child, do not use the headhugger if the
weight of baby is above 6 Kg.
To adjust the height of the safety harness, pro-
ceed as follows:
1. Remove the side joint, located at the rear
of the child car seat (diag. 7); then remove
the two ends of the safety harness from
the anchor-shaped buckle (diag. 8).
2. Remove the ends of the safety harness
from the backrest of the child car seat and
from the shoulder straps (diag. 9).
3. Remove the shoulder straps from the child
car seat (diag. 10).
After adjusting the safety harness to the cor-
rect height for your child's body, fi t the har-
ness again, as indicated below:
4. Insert the shoulder straps into the hole se-
lected (diag. 11).
5. Insert the ends of the harness into the
shoulder straps, and then into the two
holes of the harness (diag. 12).
6. After checking that the safety harness is
not twisted, fasten the two ends into the
specifi c anchor-shaped buckle, located at
the rear of the child car seat, and replace
the side joint.
WARNING: When the safety harness is insert-
ed into the hole located on the lowest posi-
tion, it is necessary to ensure that the harness
is inserted as indicated below:
7. Insert the safety harness around the guide
on the horizontal tube, located at the rear
of the backrest (diag. 13)
8. Then fasten the two ends of the safety
harness to the anchor-shaped buckle (diag.
14).
How to Fit the Child Car Seat into the
Car for Group 0+ (From 0 up to 13 Kg of
Weight).
When the child car seat is used for Group 0+,
it must be fi tted into the car only with a 3-
point safety belt. It is also necessary to recline
the child car seat as much as possible (see par-
agraph: "How to Recline the Child Car Seat").
9. Place the child car seat onto the car seat
where you wish to fi t it (diag. 15).
10. Slide the lap section of the safety belt into
the two side guides, as shown in diagram
16.
11. Pull the lap belt, ensuring that it does not
come out of the guides and that the child
car seat is placed correctly into the car
seat (diag. 17).
12. Slide the diagonal section of the safety
belt into the light blue rear guide, located
at the top, on the rear of the backrest
(diag. 18). Always tension the safety belt,
ensuring that the belt is not slack or twist-
ed.
How to Fit the Child Car Seat into the
Car for Group 1 (From 9 up to 18 Kg of
Weight).
When the child car seat is used for Group 1, it
can be fi tted into the car with a 2- point or a
3-point safety belt.
13. Place the child car seat onto the car seat
where you wish to fi t it.
14. Open the side clamp (diag. 19).
15. Pull the car safety belt, and slide it behind
the backrest of the child car seat (diag.
20).
16. Pull the safety belt to the other side of
the child car seat, and then lock the car
seat belt into the specifi c fastening buckle
(diag. 21).
Check that the lap section of the safety belt is
inserted correctly into the specifi c guides.
17. Hold and pull the diagonal section of the
safety belt, then slide it into the specifi c
clamp, as shown in diagram 22.
18. Close the locking clamp (diag. 23). The
child car seat is now fi xed into position.
If you wish to fi t the child car seat into the
central rear seat that is equipped with a 2-
point safety belt, proceed as follows:
19. Place the child car seat into the car seat
where you wish to fi t it.
31