Zoeller 118 Quick Start Manual

NOTICE TO INSTALLER: Instructions must remain with installation.
Your Peace of Mind is Our Top Priority
Product information presented
here reflects conditions at time
of publication. Consult factory
regarding discrepancies or
inconsistencies.
Register your
Zoeller Pump Company
Product on our website:
http://reg.zoellerpumps.com/
1. Inspect your unit. Occasionally, products are damaged during shipment. If the unit is damaged, contact your dealer before using.
DO NOT remove the test plug or the motor housing.
2. Carefully read the literature provided to familiarize yourself with specific details regarding installation and use. These materials should
be retained for future reference.
SEE BELOW FOR LIST OF WARNINGS
1. To reduce the risk of electrical shock, a properly grounded
receptacle of grounding type must be installed and protected
by a ground fault circuit interrupter (GFCI) and in accordance
with national electrical code and local codes.
2. Use an appropriate, gauged, extension so as not to create a
voltage drop beyond the operating parameters of the pump.
Check for cracks in the insulation, exposed wiring or electrical
taped splices. Do not use an extension cord as it could cause
a safety hazard.
3. Testing for Ground. As a safety measure, each electrical outlet
should be checked for ground using an Underwriters Laboratory
Listed circuit analyzer which will indicate if the power, neutral
and ground wires are correctly connected to your outlet. If they
are not, call a qualified electrician.
4. For electrical safety, it is recommended that a GFCI be installed.
5. FOR YOUR PROTECTION, ALWAYS DISCONNECT PUMP
FROM ITS POWER SOURCE BEFORE HANDLING. Single
phase pumps are supplied with a 3-prong grounded plug to
help protect against the possibility of electrical shock. DO NOT,
UNDER ANY CIRCUMSTANCES, REMOVE THE GROUND
PIN. To reduce the risk of electrical shock, a properly grounded
receptacle of grounding type must be installed and protected
by a ground fault circuit interrupter (GFCI) in accordance with
national electrical code and local codes.
6. Installation and checking of electrical circuits and hardware
should only be performed by a qualified, licensed electrician.
7. Risk of electric shock. These pumps have not been investigated
for use in swimming pool and marine areas.
8. According to the state of California (Prop 65), this product
contains chemicals known to the state of California to cause
cancer and birth defects or other reproductive harm.
®
MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347
SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961
TEL: (502) 778-2731 • 1 (800) 928-PUMP • FAX: (502) 774-3624
MODEL 118
FLOOD KIT
PREINSTALLATION CHECKLIST
© Copyright 2017 Zoeller
CAUTION
SEE BELOW FOR LIST OF CAUTIONS
1. Check to be sure your power source is adequate for handling
the voltage requirements of the motor, as indicated on the pump
or basin plate.
2. Make sure the pump electrical supply circuit is equipped with
fuses or circuit breakers of proper capacity. A separate branch
circuit is recommended, sized according to the National Electrical
Code for the current shown on the pump name plate.
3. Pump should be checked frequently for debris and/or build-up
which may interfere with the float "on" or "off" position. Repair
and service should be performed by a Zoeller Pump Company
Authorized Service Station only.
4. Dewatering pumps are not designed or intended for handling
raw sewage.
5. Maximum operating temperature for AquaMate submersible
pump must not exceed 110°F (43°C).
NOTE: Pumps with the "UL" mark and pumps with the "US"
mark are tested to UL Standard UL778. CSA Certified pumps
are certified to CSA Standard C22.2 No. 108.
REFER TO WARRANTY ON PAGE 2.
Co. All rights reserved.
®
visit our web site:
www.zoellerpumps.com
FM2820
0517
Supersedes
0815