Casio MZ-2000 Midi Implementation Manual page 47

MZ-2000 MIDI Implementation
13. Lo Gain
Low range level
14. Hi Freq
High range filter frequency
15. Hi Gain
High range level
16. Dir Level
Input direct signal output level
Preset List
No Preset Name
00 LoFi 1
01 LoFi 2
02 LP Scratch
03 EP Scratch
04 SP Scratch
05 50Hz Hum
06 60Hz Hum
07 7Bit Loss
08 5Bit Loss
4.8.6.33 Stereo Lo-Fi
Specifications
TypeID FXID_STLOFI = 0E41H
Available Part DSP, Master
I/O 2/2
Parameter List
ParaID Parameter Bit*Len
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
0000 Fx Name 7*16
0001 Bypass 1
0002 LoFiType 4
0003 LoFiMix 7
0004 NoiseMode 1
0005 NoiseLevel 7
0006 Lo Freq 7
0007 Lo Gain 7
0008 Hi Freq 7
0009 Hi Gain 7
000A Dir Level 7
Operation
This is a multiple effector stereo version of Lo-Fi that produces artificial Lo-Fi sounds. The
phonograh record noise generation function of the monaural Lo-Fi effector is not available in
stereo.
Stereo Lo-Fi includes the following functions, which can be enabled simultaneously.
* Reduction of input signal fidelity
* Simulation of power supply hum noise simulation
* Generation of white noise and pink noise generation
* Equalizer
1. Bypass
Effector function enable/disable. Selecting bypass causes the input signal to be output as-is.
2. LoFiType
Level of fidelity reduction in input signal. A greater value causes a greater reduction in fidel-
ity and deterioration of the tone.
3. LoFiMix
Mix level of signal whose fidelity is reduced
4. HumFreq
Hum noise frequency
5. HumLevel
Hum noise level
Value-Range Value-Meaning
20H - 7EH -
0 - 1 0...Bypass
1...Effect
0 - 8 0 - 8
0 - 127 0 - 127
0 - 1 0...White
1...Pink
0 - 127 0 - 127
8 - 40 50 - 2.0K(Hz) *Note1
52 - 64 - 76 -12dB - 0dB - +12dB
28 - 58 500 - 16.0K(Hz) *Note1
52 - 64 - 76 -12dB - 0dB - +12dB
0 - 127 0 - 127
6. NoiseMode
Noise mode: white noise or pink noise
7. NoiseLevel
White noise or pink noise level
8. Lo Freq
Low range filter frequency
9. Lo Gain
Low range level
10. Hi Freq
High range filter frequency
11. Hi Gain
High range level
12. Dir Level
Input direct signal output level
Preset List
No Preset Name
00 Bright1
01 Bright2
02 Bright3
03 Dark1
04 Dark2
05 Dark3
06 HiDump
07 PinkNoise
08 HiNoise
09 Narrow
10 Lo-Bit1
11 Lo-Bit2
12 Lo-Bit3
13 Lo-Bit WN
Presents from 06 on are initial stage noise generation settings and can be selected by MIDI only.
4.8.7 FX Parameter Set Bulk Dump
The FX Parameter Set can be sent and received using bulk dump. There are two protocols, One-
Way and Handshake, which are the same as those described under "4.1 MZ-2000 Sound Source
Common System Exclusive Format."
The following shows the section that applies to effects only.
tt 0100aaaa aaaa = BDS..."SYSEX_ACT_BDS" = 02H
d0[0] 0ooocccc cccc = Parameter Set Category = FX = 03H
ooo = 00H
d0[1] 0ttttttt 0TTTTTTT0ttttttt = Type ID = See the description of each effect
d0[2] 0TTTTTTT
d0[3] 0mmmmmmm 0MMMMMMM0mmmmmmm = Mdev ID = Internal RAM = 2F00H
d0[4] 0MMMMMMM
d0[5] 0sssssss 00SSSSSSSsssssss = Section Number
d0[6] 0SSSSSSS
The mixer (MIX) Part/Segment numbers selected by FX go here. This is the same
for IPC and IPR.
d0[7] 0nnnnnnn 00NNNNNNNnnnnnnn = PS Number = 0000H Fixed
d0[8] 0NNNNNNN
The content and size of the data depend on the FX. Since the volume of data is very large, and it is
not included here. This data can be looked up by sending HDR and BDR.
46
BDR..."SYSEX_ACT_BDR" = 03H
HDS..."SYSEX_ACT_HDS" = 04H
HDR..."SYSEX_ACT_HDR" = 05H
HDA..."SYSEX_ACT_HDA" = 06H
HDJ..."SYSEX_ACT_HDJ" = 07H
HDE..."SYSEX_ACT_HDE" = 08H
(FX) for details about Type IDs.