Casio MZ-2000 Midi Implementation Manual page 36

MZ-2000 MIDI Implementation
Operation
This effector enhances the quality of the input signal to produce a richer tone. It can be used to
control thelevels of two bands.
1. Bypass
Effector function enable/disable. Selecting bypass causes the input signal to be output as-is.
2. Lo Gain
Low-range level
3. Hi Gain
High-range level
4. Level
Output level
Preset List
No Preset Name
00 HiEnh1
01 HiEnh2
02 Loud1
03 Loud2
04 LoEnh
4.8.6.11 Stereo Enhancer
Specifications
TypeID FXID_STENH = 0205H
Available Part DSP, Master
I/O 2/2
Parameter List
ParaID Parameter Bit*Len Value-Range
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
0000 Fx Name 7*16
0001 Bypass 1
0002 Lo 7
0003 Hi 7
0004 Level 7
Operation
This effector is a two-channel left-right input version of Enhancer. Its operations and parameters
are identical tothose of Enhancer. Parameter operations are identical for the left and right chan-
nels.
Preset List
No Preset Name
00 HiEnh1
01 HiEnh2
02 LoEnh1
03 LoEnh2
04 Loudness1
05 Loudness2
06 +Lo-Hi
07 -Lo+Hi
4.8.6.12 Wah
Specifications
TypeID FXID_WAH = 0240H
Available Part DSP
I/O 1/1
Value-Meaning
20H - 7EH -
0 - 1 0...Bypass
1...Effect
0 - 64 -127 -64 - 0 - +63
0 - 64 -127 -64 - 0 - +63
0 - 127 0 - 127
Parameter List
ParaID Parameter
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
0000 Fx Name
0001 Bypass
0002 FilterType
0003 Freq
0004 Resonance
0005 Depth
0006 Rate
0007 Waveform
0008 Step
Operation
This effector produces a distinctive wah-wah effect by using a filter to enhance a particular fre-
quency band of the input signal, and by shifting the frequency in accordance with the changes in
the cutoff parameter caused by pedal, wheel, or other controller operation.
This effector also has a built-in LFO, which can be used to modulate the high range of the filter
frequency based on the Cutoff setting.
1. Bypass
Effector function enable/disable. Selecting bypass causes the input signal to be output as-is.
2. FilterType
Either BPF (Band Pass Filter) or LPF (Low Pass Filter) can be selected as the filter type.
Using BPF outputs only narrow band signals, so the change in the tone is great.
3. Freq
When BPF is selected, this parameter controls the mid-range equalizer center trigger fre-
quency. When LPF is selected, this parameter controls the mid-range equalizer trigger fre-
quency.
4. Resonance
Wah effect resonance
5. Depth
Width of frequency band shifted by an LFO. Setting 0 disables LFO operation.
6. Rate
LFO speed.
7. Waveform
LFO waveform.
o Sin......Sine wave
o SawUp....Sawtooth wave (rising)
o SawDw....Sawtooth wave (falling)
o Squ......Square wave
8. Step
LFO continuity. A value of 0 specifies smooth change, while a larger value specifies coarser
change.
Preset List
No Preset Name
00 Low Fix
01 Mid Fix
02 Hi Fix
03 LFO-1
04 LFO-2
05 LFO-Up
06 LFO-Down
07 LFO-Squ
08 LFO-Step1
09 LFO-Step2
10 LFO-3
35
Bit*Len Value-Range Value-Meaning
7*16 20H - 7EH -
1 0 - 1 0...Bypass
1...Effect
1 0 - 1 0...BPF
1...LPF
7 0 - 127 0 - 127
7 0 - 127 0 - 127
7 0 - 127 0 - 127
7 0 - 127 0 - 127
3 0 - 4 0...Sin
1...Tri
2...SawUp
3...SawDw
4...Squ
7 0 - 127 0 - 127