Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Fortis SK-2200A
Summary of Contents for Fortis SK-2200A
- Page 1 AUTOMATIC VARIABLE RESISTANCE MAGNETIC FLYWHEEL SPIN BIKE (SK-2200A) FSEMSB2200A...
-
Page 3: Safety And Warnings
SAFETY & WARNINGS Read all of the instructions in this guide before using this product. Retain this guide for future reference. Do not skip, substitute or modify any steps or procedures in this guide, as doing so could result in personal injury or product damage. •... - Page 4 • Always use the equipment as intended. If you find any defective components while assembling or checking the equipment, or if you hear any unusual noises coming from the equipment during exercise, cease use immediately and contact help.kogan.com for support. Do not use until resolved. •...
- Page 5 OVERVIEW Components:...
- Page 6 Console Induction cord Handlebars Seat Handlebar cover (upper) Power cord (lower) Handlebar cover (lower) Right foot pedal Handlebar post Left foot pedal Pull pin 13-15 Spanner Frame base Allen key 1 Front stabiliser Allen key 2 Rear stabiliser Power cord (upper) Hardware: 2 M8x10L (x4) 4 M8x12L (x4)
- Page 7 ASSEMBLY Step 1 Attach the front and rear stabilisers (29) (68) using the screws, washers and spring washers (34, 35, 36) and Allen Key (93) shown below.
- Page 8 Step 2 Attach the seat (79).
- Page 9 Step 3 Attach the (82) (95) wiring, then fit the handlebar post (10).
- Page 10 Step 4 Set the handlebar post into position with the Pull pin (15).
- Page 11 Step 5 Attach the handlebars (3).
- Page 12 Step 6 Fit the handlebar cover assembly (7) (8).
- Page 13 Step 7 Fit the Console (1).
- Page 14 Step 8 Attach the left and right pedals (85) (89).
-
Page 15: Operation
OPERATION Buttons START/STOP Start or stop exercise program RESET In manual mode, press this button to return to the main menu. Press and hold this button for 2 seconds to restart the display. UP (+) Increase the selected training mode. Increase selected value. - Page 16 Operation Function After connecting to a power supply, press and hold the RESET button for 2 seconds, you will hear a buzzer beep for 1 second and a full LCD display for 2 seconds (Figure 1). After displaying the screen shown in Figure 2 for 1 second, the console will enter the standby screen (Figure 3).
- Page 17 Button Functions A. UP/DOWN buttons: Select Manual, Beginner, Advance, Sporty, Cardio, Watt, etc. After entering the setting mode, press the UP or DOWN buttons to cycle through the selections. Adjusting Resistance While in quick start mode, pressing the UP/DOWN buttons will adjust the resistance (LOAD) level.
- Page 18 B. MODE button: • Press this BUTTON to select MANUAL, TIME, DST or CAL. • When you select a function, it is displayed on the console to indicate that it is currently configurable. • Pressing the MODE button again will proceed to the next operation. Note: The above actions can only be performed when the bike is in standby.
- Page 19 E. RECOVERY button If no PULSE input is available, press The RECOVERY button to disable this function. Press this BUTTON once after the PULSE value is displayed. • The TIME and PULSE values of RECOVERY are displayed (Figure 9). • The TIME window displays "0:60"...
-
Page 20: Cleaning And Care
CLEANING & CARE • Examine the equipment regularly to check for signs of wear or any damage. • Lubricate moving parts with light oil periodically to prevent premature wear. • Inspect and tighten all parts before using the equipment, replace any defective parts immediately and do not use the equipment again until it is in perfect working order. - Page 21 NOTES...
- Page 24 Need more information? We hope that this user guide has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com...
Need help?
Do you have a question about the SK-2200A and is the answer not in the manual?
Questions and answers