Calculated Industries 4030 User Manual

Calculated Industries 4030 User Manual

Construction master pro series
Table of Contents

Advertisement

C
ONSTRUCTION
4075 C
4060 C
4030 C
44060 C
44065 C
ONSTRUCTION
ONSTRUCTION
U
G
M
ASTER
ONSTRUCTION
M
ONSTRUCTION
ASTER
M
ONSTRUCTION
ASTER
M
P
ASTER
®
RO
M
P
T
ASTER
®
RO
SER'S
UIDE
P
RO
®
F
M
OR
ODELS:
M
P
ASTER
®
RO
P
LT
®
RO
P
DT
®
RO
DT P
RINTER
P
III
RIG
LUS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 4030 and is the answer not in the manual?

Questions and answers

Summary of Contents for Calculated Industries 4030

  • Page 1 ONSTRUCTION 44065 C 4075 C ASTER 4060 C ONSTRUCTION 4030 C ONSTRUCTION 44060 C ONSTRUCTION ONSTRUCTION ASTER ONSTRUCTION ASTER ® SER’S UIDE ® ODELS: ASTER ® ASTER ® ASTER ® DT P ® RINTER ™...
  • Page 2 Construction Master Pro DT Printer (Desktop model) Model 44065 Construction Master Pro Model 4060...
  • Page 3: Construction Master ® Pro User's Guide

    Construction Master calculators—five of the most powerful feet-inch-fraction calculators to date: The Construction Master Pro Series — 1. LT (#4030) 2. Handheld (#4060) 3. Trig Plus III (#4075) 4. Desktop (#44060) 5. New! Desktop with Printer (#44065)* *CI now offers a Printing Model—the Construction Master Pro DT...
  • Page 4: Table Of Contents

    TABLE OF CONTENTS CONSTRUCTION MASTER INTRODUCTION ...7 CONSTRUCTION MASTER COMPARISON ...8 KEY DEFINITIONS...9 Basic Operation Keys... 9 Convert [Conv] Key—Unit Conversions and Second Functions ...10 Memory and Storage Functions ...11 Recall [Rcl] Key ...12 Dimensional Measurement Unit Keys...13 Weight Keys...14 Construction Project Keys ...15 Block/Brick Key ...15 Circular Function Keys ...16...
  • Page 5 Cubic Conversions ... 31 PERFORMING BASIC MATH WITH DIMENSIONS ...32 Adding Dimensions ... 32 Subtracting Dimensions... 32 Multiplying Dimensions... 32 Dividing Dimensions ... 33 Percentage Calculations ... 33 MEMORY OPERATION...34 PAPERLESS TAPE OPERATION ...36 EXAMPLES — USING THE CONSTRUCTION MASTER PRO...38 LINEAR MEASUREMENT EXAMPLES ...39 Adding Linear Measurements...
  • Page 6 CIRCLE CALCULATIONS ...49 Circumference and Area of a Circle ...49 Circle Properties — Arc Length and Diameter Known...49 Arched Windows ...51 Arc Length — Degree and Diameter Known ...52 Arc Length — Degree and Radius Known ...52 CONCRETE/PAVING...53 Volume of Concrete for a Driveway ...53 Concrete Columns...54 Complex Concrete Volume...56 Concrete Footings (not available on Trig Plus III)...58...
  • Page 7 APPENDIX A — DEFAULT SETTINGS ...95 Metric Mode ... 95 APPENDIX B — PREFERENCE SETTINGS ...96 How to Set Preferences ... 99 LT (#4030)... 100 Handheld (#4060) and Desktop (#44060) ... 101 Trig Plus III (#4075) ... 103 APPENDIX C — USING THE DESKTOP PRINTING MODEL (DT PRINTER: #44065)...105...
  • Page 8 APPENDIX E — ACCURACY, AUTO SHUT- OFF, BATTERIES, ERRORS... 119 Accuracy/Errors ... 119 Auto Shut-Off... 120 Battery(ies)... 120 Replacing the Battery(ies)... 120 Battery Replacement Instructions ... 120 Reset Key ... 121 APPENDIX F — AREA/VOLUME FORMULAS ... 122 REPAIR AND RETURN ... 124 WARRANTY...
  • Page 9: Introduction

    Your Calculator Helps You Solve: Dimensional Math Problems Conversions Between Feet-Inch-Fractions, Decimal Feet, Deci- mal Inch and Yards English/Metric Conversions Problems Involving All Common Fractions –...
  • Page 10: Construction Master Pro - Key/Function Comparison

    Pitch, Rise, Run, Diag. Rake Wall Roof Framing Keys (Reg. and Irreg. Hip/ Valley, Jacks, Cuts) Roof Area and Bundles Stair Trigonometric Keys Preference Settings 8 — CONSTRUCTION MASTER PRO ® PRO — Hand- held (#4060) (#4030) (#44060 Trig Plus III (#4075)
  • Page 11: Key Definitions

    KEY DEFINITIONS BASIC OPERATION KEYS [On/C] — On/Clear Turns power on. Pressing once clears the display. Pressing twice clears all temporary values. [Off] Turns all power off, clearing all non-permanent registers. [+] [–] [x] [÷] [=] Arithmetic operation keys. Four-function percent key. [0] –...
  • Page 12: Convert [Conv] Key-Unit Conversions And Second Functions

    Convert [Conv] Key—Unit Conversions and Second Functions The [Conv] key is to convert between measurement units or to access second functions, listed below: [Conv] — Convert Used with the measurement keys to convert between units or with other keys to access special functions. [Conv] [ x ] —...
  • Page 13: Memory And Storage Functions

    Note: Non-cumulative means it only accepts one value (does not add or subtract) and a second entered value will replace the first. Permanent means the value is stored even after the calculator is shut off. To delete a stored value, enter a new value or perform an All Clear [Conv] [x].
  • Page 14: Recall [Rcl] Key

    Recall [Rcl] Key The [Rcl] key is used to recall or review stored values (e.g., [Rcl] [Pitch] to recall a previously entered pitch value). It is also used in re- viewing stored settings, or in Paperless Tape and Memory operation (see below).
  • Page 15: Dimensional Measurement Unit Keys

    Used to enter fractions. Fractions may be entered as proper (1/2, 1/8, 1/16) or improper (3/2, 9/8). If the denominator (bottom) is not entered, the calculator's fractional resolution setting is automatically used (e.g., entering 15 [/] [=] or [+] will display 15/16, based on the default fractional resolution setting of 16ths (default setting for Trig Plus III is 64ths).
  • Page 16: Weight Keys

    [Conv] [ 2 ] — Acres Enters or converts (a square value) to acres. [Conv] [ 0 ] — Board Feet Enters or converts cubic values to board feet. One board foot is equal to 144 cubic inches. WEIGHT KEYS [Conv] [ 1 ] —...
  • Page 17: Construction Project Keys

    Construction Project Keys The following Construction Project Keys help you instantly figure quan- tities and costs of materials, so you can build like a pro! Block/Brick Key The Block key helps you quickly estimate the quantity of blocks or bricks required for building walls, walkways or other areas. [Block] —...
  • Page 18: Circular Function Keys

    Circular Function Keys The circle key helps you quickly solve circular area, volume or arc problems. [Circ] — Circle Displays and calculates the following values, given an entered circle diameter* or radius: diameter circle area circumference *To enter a diameter (e.g., 10 feet), press 10 [Feet] [Circ]. [Conv] [Diag] —...
  • Page 19: Column/Cone Key

    [Rise] — Rise (Segment Rise) Used with [Run] or [Conv] [Diag] to find the rise or the radius of a circular segment. If the chord length and radius have been entered, this key will display the segment rise of the circular segment. Column/Cone Key The Column and Cone functions help you quickly estimate volume and surface area of columns or cones.
  • Page 20: Right Triangle/Roof Framing Keys

    Right Triangle/Roof Framing Keys Right Triangle: Pitch = Using the Pythagorean theorem, the top row of keys on your Construc- tion Master Pro provide instant solutions in dimensional format to right triangle problems (particularly, roof framing). The Construction Master Pro’s keys are labeled in easy to remember roofing terms.
  • Page 21 To change the pitch, simply enter a new pitch value. In contrast, a calculated pitch value is not permanently stored. This means that the calculator will return to the pitch value you last entered when you clear the calculator or press [On/C] twice.
  • Page 22: Hip/Valley And Jack Rafter Keys

    When calculating regular and irregular Jack rafter lengths, you will see the letters “JK” (Common pitch side) or “IJ” (irregular pitch side) and the corresponding Jack number to the left of your calculator display. This will help you keep track of the descending sizes and which side the corresponding rafter is based on.
  • Page 23 þ þ Note: You may set your calculator to display the Jack rafter lengths in either ascending or descending order (see Preference Settings on page 96). þ þ...
  • Page 24: Rake Wall Function

    [Conv] [Jack] — Irregular Side Jacks Operates same as [Jack], but displays the rafter values from the irregular pitched side first. Rake Wall Function [Conv] [Rise] — Rake Wall This function finds the stud sizes in a Rake Wall given computed or entered values for pitch, rise and/or run.
  • Page 25: Roof Key

    Roof Key The Construction Master Pro's Roof function provides a quick computa- tion of roof area, given a floor area and a roof pitch. In addition, this function also converts the calculated Roof Area into a quantity of (33- 1/3 square feet) bundles of shingles. [Roof] Converts an entered floor area into a roof area.
  • Page 26: Stair Key

    Stair Key The Construction Master Pro easily computes stair layout solutions. Given values for rise and/or run, your calculator will compute riser, tread, stringer and angle of incline values simply by pressing the [Stair] key. [Stair] A multi-function key that uses a stored desired riser height, desired...
  • Page 27: Trigonometry Function Keys

    TRIGONOMETRY FUNCTION KEYS Hypotenuse Opposite Side Adjacent Side Tangent Ø Sine Ø Cosine Ø The Desktop and Trig Plus III calculators have standard trigonometric keys, in addition to Right Triangle/Rafter keys (e.g., Rise, Run, Diago- nal), for advanced right triangle mathematics. The sine, cosine and tangent of an angle are defined in relation to the sides of a right triangle.
  • Page 28 [Sine] — Sine Function Computes the sine of a degree or undimensioned* value. [Conv] [Sine] — Arcsine (sin Computes the angle for the entered or calculated sine value. [Cos] — Cosine Function Computes the cosine of a degree or undimensioned value. [Conv] [Cos] —...
  • Page 29: Getting Started

    GETTING STARTED ENTERING DIMENSIONS Entering Linear Dimensions When entering feet-inch-fraction values, enter dimensions from largest to smallest — e.g., feet before inches, inches before fractions. Enter fractions by entering the numerator (top), pressing [ / ] (fraction bar key) and then the denominator (bottom). þ...
  • Page 30 Examples of Square and Cubic Entry: [Yds] [Yds] — Square Yards (e.g., 5 [Yds] [Yds] will display 5. SQ YD). [Yds] [Yds] [Yds] — Cubic Yards (e.g., 5 [Yds] [Yds] [Yds] will display 5. CU YD). [Feet] [Feet] — Square Feet (e.g., 5 [Feet] [Feet] will display 5.
  • Page 31: Conversions (Linear, Area, Volume)

    CONVERSIONS (LINEAR, AREA, VOLUME) Linear Conversions Convert 14 feet to other dimensions: Keystroke [On/C] [On/C] 14 [Feet] [Conv] [Yds] [Feet] [Inch] [Conv] [5] (cm) [mm] þ þ Note: When performing multiple conversions, you only have to press the [Conv] key once. Converting Feet-Inch-Fractions to Decimal Feet Convert 15 feet 9-1/2 inches to decimal feet.
  • Page 32: Converting Decimal Feet To Feet-Inch-Fractions

    Converting Decimal Feet to Feet-Inch-Fractions Convert 17.32 feet to feet-inch-fractions. Keystroke [On/C] [On/C] 17.32 [Feet] [Conv] [Feet] Converting Fractional Inches to Decimal Inches Convert 8-1/8 inches to decimal inches. Then convert to decimal feet. Keystroke Display [On/C] [On/C] 8 [Inch] 1 [/] 8 [Conv] [Inch] [Feet] Converting Decimal Inches to Fractional Inches...
  • Page 33: Square Conversions

    þ þ *Note: The calculator's auto-range function displayed the answer in meters because the answer in millimeters is out of the calculator's normal 7 -digit range. The Trig Plus III may show the result in mm u s- ing Exponential Notation format. If the Exponential Notation Prefer-...
  • Page 34: Performing Basic Math With Dimensions

    PERFORMING BASIC MATH WITH DIMENSIONS Adding Dimensions Keystroke Add 11 inches to 2 feet 1 inch: 11 [Inch] [+] 2 [Feet] 1 [Inch] [=] Add 5 feet 7-1/2 inches to 18 feet 8 inches: 5 [Feet] 7 [Inch] 1 [ / ] 2 [+] 18 [Feet] 8 [Inch] [=] Subtracting Dimensions Keystroke Subtract 3 feet from 11 feet 7-1/2 inches:...
  • Page 35: Dividing Dimensions

    Dividing Dimensions Keystroke Divide 30 feet 4 inches by 7 inches: 30 [Feet] 4 [Inch] [÷] 7 [Inch] [=] Divide 20 feet 3 inches by 9: 20 [Feet] 3 [Inch] [÷] 9 [=] Percentage Calculations The percent [%] key is used to find a given percent of a number or to perform add-on, discount or division percentage calculations.
  • Page 36: Memory Operation

    MEMORY OPERATION Your calculator has two types of Memory operations: 1) a standard, cumulative, semi-permanent memory [M+]; and 2) two Storage Registers [M1] and [M2], used to permanently store single, non-cumulative values. Memory commands are listed below. Function Add value to M+...
  • Page 37: Basic Cumulative Memory (M+)

    þ þ Note: To Clear M1/M2: Values stored in M1/M2 will remain per- manently stored, even after you turn the calculator off. You will never need to clear the storage registers; simply enter a new value. However, if you wish to clear M1/M2 to “zero”:...
  • Page 38: Paperless Tape Operation

    þ þ Note: The Paperless Tape is cleared when: [On/C] is pressed twice; upon a new calculation (new equation string is started); or when the calculator is shut off. 36 — CONSTRUCTION MASTER PRO...
  • Page 39 Example: Keystroke 1. Enter a string of numbers: 4 [Feet] [+] 5 [Feet] [+] 6 [Feet] [+] 7 [Feet] [=] 2. Access the tape function: [Rcl] [=] 3. Scroll from first value to total: 4. Scroll last two values: [–] [–] 5.
  • Page 40: Examples - Using The Construction Master Pro

    (refer to the Comparison Grid on page 8). Also, if you are using the Trig Plus III, some of your answers in this User’s Guide may differ slightly, as the calculator has a default frac- tional resolution of 1/64" (versus 1/16" in other models). A special key- stroke, [Conv] [1], temporarily sets the fractional setting to sixteenths in selected problems.
  • Page 41: Linear Measurement Examples

    LINEAR MEASUREMENT EXAMPLES Adding Linear Measurements Find the total length of the following measurements: 5 feet 4-1/2 inches, 8 inches and 3.5 yards. Keystroke 1. Add the measurements: [On/C] [On/C] 5 [Feet] 4 [Inch] 1 [/] 2 [+] 8 [Inch] [+] 3.5 [Yds] 2.
  • Page 42: Window Measurement

    Window Measurement What is the total width of three (3) window openings, if each measures 2 feet 5 inches in width? Keystroke 1. Enter window width: [On/C] [On/C] 2 [Feet] 5 [Inch] 2. Find total width: [x] 3 [=] 3. Convert to decimal feet: [Feet] Calculating the Center Point You have a room that measures 13 feet 8 inches by 14 feet 10 inches.
  • Page 43: Area Calculations

    AREA CALCULATIONS Square Area (x What is the area of a square room with sides measuring 7 feet 4 inches? Keystroke [On/C] [On/C] 7 [Feet] 4 [Inch] [Conv] [%] (x Area of a Rectangular Room (LxW) What is the area of a room measuring 12 feet 6 inches by 15 feet 8 inches? Keystroke [On/C] [On/C]...
  • Page 44: Volume Calculations

    VOLUME CALCULATIONS Rectangular Containers (LxWxH) What is the volume of a rectangular container that measures 3 feet by 1 foot 9-5/8 inches by 2 feet 4 inches? Keystroke 1. Find volume in cubic feet: [On/C] [On/C] 3 [Feet] [x] 1 [Feet] 9 [Inch] 5 [ / ] 8 [x] 2 [Feet] 4 [Inch] [=] 2.
  • Page 45: Volume Of A Cylinder

    Volume of a Cylinder Calculate the volume of a cylinder with a diameter of 2 feet 4 inches and a height of 4 feet 6 inches: h=4’ 6” Keystroke 1. Find circle area: [On/C] [On/C] 2 [Feet] 4 [Inch] [Circ] [Circ] 2.
  • Page 46: Weight/Volume Conversions

    WEIGHT/VOLUME CONVERSIONS Weight Conversions Convert 2,500 pounds to kilograms, tons and metric tons: Keystroke 1. Enter pounds: [On/C] [On/C] 2500 [Conv] [4] (lbs) 2. Convert to kilograms, tons and metric tons: [Conv] [1] (kg) [Conv] [6] (tons) [Conv] [3] (met tons) 44 —...
  • Page 47: Weight Per Volume/Volume Conversions

    Weight per Volume/Volume Conversions Convert 5 cubic yards of concrete to pounds, tons and kilograms, if concrete weighs 1.5 tons per cubic yard. Keystroke 1. Store weight per volume: [On/C] [On/C] 1.5 [Stor] [8]* (wt/vol) 2. Enter concrete volume: 5 [Yds] [Yds] [Yds] 3.
  • Page 48: Blocks/Bricks

    BLOCKS/BRICKS Number of Blocks (not available on LT and Trig Plus III) You are building an “L” shaped retaining w all out of standard 8-inch x 16-inch size blocks (note: default block size). One side of the retain- ing wall is 22 feet long, and the other side is 15 feet 8 inches long. The wall is to be 4 feet high.
  • Page 49: Number Of "Face" Bricks (Not Available On Lt And Trig Plus Iii)

    Number of “Face” Bricks (not available on LT and Trig Plus III) How many “face” bricks (21 square inch size) will you need to pur- chase to fill a 40 foot by 8 foot wall, if you include a 3% waste allow- ance? Keystroke 1.
  • Page 50: Board Feet - Lumber Estimation

    BOARD FEET — LUMBER ESTIMATION The Construction Master Pro easily computes board feet for lumber es- timation problems. Simply enter the board’s cubic dimensions and press the [Conv] [0] keys to convert to board feet. Use the [Conv] [9], or “Cost” function, to figure total lumber cost. þ...
  • Page 51: Circle Calculations

    CIRCLE CALCULATIONS Circumference and Area of a Circle Find the area and circumference of a circle with a diameter of 11 inches: Keystroke [On/C] [On/C] 11 [Inch] [Circ] [Circ] [Circ] Circle Properties — Arc Length and Diameter Known Find the arc degree, chord length, rise, pie slice area and segment area of a circle, given a 5-foot diameter and an arc length of 3 feet 3 inches: Keystroke...
  • Page 52 (Cont’d) Keystroke 3. Find degree of arc: [Circ] 4. Find chord length: [Circ] 5. Find segment rise: [Circ] 6. Find pie slice area: [Circ] 7. Find segment area: [Circ] þ þ Note: Successive presses of [Circ] will toggle to the beginning. 50 —...
  • Page 53: Arched Windows

    Arched Windows Find the radius of an arched window with a chord length of 2 feet 7 inches and a rise of 10-1/2 inches. Then, find the arc angle, arc length and segment area of the window. Rise=10-1/2” Keystroke 1. Enter chord length: [On/C] [On/C] 2 [Feet] 7 [Inch] [Run] 2.
  • Page 54: Arc Length - Degree And Diameter Known

    Arc Length — Degree and Diameter Known Find the arc length of an 85° portion of a circle with a 5-foot diameter: Keystroke [On/C] [On/C] 5 [Feet] [Circ] 85 [Conv] [Circ] [Circ] Arc Length — Degree and Radius Known Find the arc length of a circle with a 24-inch radius and 77 of arc (77 of 360 circle): Keystroke [On/C] [On/C]...
  • Page 55: Concrete/Paving

    CONCRETE/PAVING Volume of Concrete for a Driveway Find the cubic yards of concrete required to pour a driveway with the following dimensions: 36 feet 3 inches long by 11 feet 6 inches wide by 4 inches deep. If concrete costs $55 per cubic yard, what is the total cost? Keystroke 1.
  • Page 56: Concrete Columns

    Concrete Columns Find the cubic yards of concrete required to pour five (5) columns, if each has a diameter of 3 feet 4-1/2 inches and a height of 11 feet 6 inches. If the concrete weighs 1.75 tons per cubic yard, what is the to- tal weight in tons? In pounds? In kilograms? Keystroke 1.
  • Page 57 (Cont’d) 4. Recall Memory and find weights: [Rcl] [Rcl] [Conv] [6] (tons) [Conv] [4] (lbs) [Conv] [1] (kg) 19.05204 CU YD 33.34107 Ton 66682.14 LB 30246.51 kG 11’ 6” 3’ 4-1/2” User's Guide — 55...
  • Page 58: Complex Concrete Volume

    Complex Concrete Volume You’re going to pour an odd-shaped patio 4-1/2 inches deep with the dimensions shown below. Calculate the total area (by dividing the draw- ing into three rectangles) and determine the total yards of concrete re- quired. Then, find the total cost, if concrete costs $45 per cubic yard. 27’...
  • Page 59 (Cont’d) Keystroke 1. Find area of Part A and store into Memory: [On/C] [On/C] 17 [Feet] 6 [Inch] [–] 7 [Feet] [=] [x] 27 [Feet] [=] [M+] 2. Find area of Part B and store into Memory: 7 [Feet] [x] 9 [Feet] [=] [M+] 3.
  • Page 60: Concrete Footings (Not Available On Trig Plus Iii)

    Concrete Footings (not available on Trig Plus III) Find the volume of concrete required for a (16 inch by 8 inch) footing that measures 232 feet 6 inches in length. Keystroke 1. Enter footing area: [On/C] [On/C] 16 [Inch] [x] 8 [Inch] [=] [Stor] [Ftg] 2.
  • Page 61: Squaring Up A Foundation

    Squaring Up a Foundation A concrete foundation measures 45 feet 6 inches by 23 feet 8 inches. Find the diagonal measurement (square up) to ensure the form is per- fectly square. Keystroke 1. Enter sides as rise/run: [On/C] [On/C] 23 [Feet] 8 [Inch] [Rise] 45 [Feet] 6 [Inch] [Run] 2.
  • Page 62: Floor Covering Area Calculations

    FLOOR COVERING AREA CALCULATIONS Carpeting You need to replace the carpet in two rooms, with dimensions as fol- lows: (Room #1) 12 feet 4 inches x 10 feet; (Room #2) 14 feet 8 inches x 16 feet. Find the total square yards of carpet required. Keystroke 1.
  • Page 63: Grade/Slope

    GRADE/SLOPE Back-Fill on a Slope — Percent of Grade Known You’ve built 55 linear feet of a 3 foot high retaining wall that is 3 feet from the base of a 65% grade. You need to pour back-fill within 12 inches of the top of the wall (for a 2 foot depth).
  • Page 64 (Cont’d) Keystroke 3. Find volume of triangle “B”: 55 [Feet] [x] [Rcl] [Run] [x] 2 [Feet] [=] [÷] 2 [=] [M+] 4. Find total volume: [Rcl] [Rcl] [Conv] [Yds] 62 — CONSTRUCTION MASTER PRO Display 55 FEET RUN 3 FEET 0-15/16 INCH 338.4615 CU FEET 169.2308 CU FEET 499.2308 CU FEET...
  • Page 65: Right Triangle And Roof Framing Examples63

    RIGHT TRIANGLE AND ROOF FRAMING EXAMPLES ROOF FRAMING DEFINIT IONS Rise : The vertical distance measured from the wall’s top plate to the intersection of the pitch line and the center of the ridge. Span: The horizontal distance or full width between the outside edges of the wall’s top plates.
  • Page 66 Plate: The top horizontal wall member that the ceiling joist and rafters sit on and fasten to. Ridge: The uppermost point of two roof planes. Ridge Rafter: Also known as the “King rafter,” this rafter is the uppermost rafter that all Hip, Valley, Valley Jack and Common rafters are fastened to.
  • Page 67 Level Cut Angle Irregular Side [I/Jack] Cheek Angle Plumb: Vertical Cut. The angle of cut from the edge of the board that allows the rafter to mate on the vertical side of the ridge rafter. Level: Horizontal Cut. The angle of cut from the edge of the board that allows the rafter to seat flat on the wall plate.
  • Page 68: Common Rafter Length

    Common Rafter Length If a roof has a 7/12 pitch and a span of 14 feet 4 inches, what is the point-to-point length of the Common rafter (excluding the overhang or ridge adjustment)? What are the Plumb and Level cuts? Keystroke 1.
  • Page 69: Common Rafter Length - Pitch Unknown

    Common Rafter Length — Pitch Unknown Find the Common rafter length for a roof with a rise of 6 feet 11-1/2 inches and a run of 14 feet 6 inches. Solve for the pitch in inches and degrees. Keystroke Find diagonal and pitch: [On/C] [On/C] [Conv] [1]* 6 [Feet] 11 [Inch] 1 [ / ] 2 [Rise]...
  • Page 70: Rise

    Rise Find the rise given a 7/12 pitch and a run of 11 feet 6 inches. Keystroke [On/C] [On/C] 7 [Inch] [Pitch] 11 [Feet] 6 [Inch] [Run] [Rise] Rise and Diagonal Find the rise and diagonal of a right triangle given a 30° pitch and a run of 20 feet 4 inches.
  • Page 71: Finding Sheathing Cut

    Finding Sheathing Cut You have framed an equal pitch roof and need to apply the roof sheath- ing. Find the distance from the corner of the sheathing so that you can finish the run at the Hip rafter and cut the material. The pitch is 6 inches and you are using 4-foot by 8-foot plywood, with the 8-foot side along the plate.
  • Page 72: Regular (45°) Hip/Valley And Jack Rafters (Not Available On Lt)

    Regular (45°) Hip/Valley and Jack Rafters (not avail- able on LT) You’re working with a 7/12 pitch, and half your total span is 8 feet 5 inches: (1) Find point-to-point length and cut angles for the Common rafter; (2) Find the length and cut angles of the adjoining Hip (or Valley) and; (3) Find the regular Jack rafter lengths and cut angles (Jack rafters at 16 inches on-center spacing).
  • Page 73 (Cont’d) Keystroke 3. Find Jack rafter lengths and cut angles: [Jack] [Jack] [Jack] [Jack] [Jack] [Jack] [Jack] [Jack] [Jack] [Jack] [Jack] þ þ *Note: If display does not read JKOC 16 INCH (the default), then re- set by pressing 16 [Inch] [Stor] [7]. Display JKOC 16 INCH* JK1 8 FEET 2-3/8 INCH...
  • Page 74: Jack Rafters - Using Other Than 16 Inch On-Center Spacing (Not Available On Lt)

    Jack Rafters — Using Other Than 16 Inch On-Center Spacing (not available on LT) A roof has a 9/12 pitch and a run of 6 feet 9 inches. Find the Jack raf- ter lengths and cut angles at 18-inch (versus 16-inch) on-center spacing.
  • Page 75: Irregular (Non-45°) Hip/Valley And Jack Rafters - Descending, With On-Center Spacing Maintained (Not Available On Lt)

    Complete the following steps: (1) Find the length of the Common rafter; (2) Reset calculator to 16 inch on-center spacing; (3) Enter the irregular pitch; find the length of the adjoining “irregular” Hip (or Valley) and the cut angles;...
  • Page 76 (Cont’d) Keystroke 4. Find irregular Jack lengths: [Conv] [Jack] [Jack]* [Jack] [Jack] þ þ Note: It is not necessary to continue pressing [Conv] when display- ing each Jack rafter size. 5. Find irregular Jack Plumb, Level and Cheek cut angles: [Jack] [Jack] [Jack]...
  • Page 77: Irregular (Non-45°) Hip/Valley And Jack Rafters - Ascending, With

    Irregular (non-45°) Hip/Valley and Jack Rafters — Ascending, with Jacks Mating at Hip/Valley available on LT) You’re working with a 7/12 pitch and half your overall span is 4 feet. The irregular pitch is 8/12, and the Jacks need to mate at the Hip. The maximum allowable on-center spacing is 16 inches.
  • Page 78 (Cont’d) Keystroke 3. Find Common rafter length: 7 [Inch] [Pitch] 4 [Feet] [Run] [Diag] 4. Enter irregular pitch and find irregular Hip/Valley rafter length and cut angles: 8 [Inch] [Conv] [Hip/V] [Hip/V] [Hip/V] [Hip/V] [Hip/V] [Hip/V] 5. Find the o.c., irregular Jack lengths and cut angles: [Conv] [Jack] [Jack] [Jack]...
  • Page 79: Rake Wall - No Base

    Rake Wall – No Base Find each stud size in a Rake Wall with a peak of 4 feet, and a length of 8 feet. Use 16 inches as your spacing. Rise=4’ þ þ Note: The wall has no base. Keystroke 1.
  • Page 80 (Cont’d) Keystroke 2. Find stud lengths: [Conv] [Rise] (R/Wall) [Rise] [Rise] [Rise] [Rise] [Rise] [Rise] 3. Find Rake Wall angle of incline: [Rise] þ þ Note: By setting the Rake “Ascend” Preference (see Preference Set- tings on page 96), you may view Rake Wall stud lengths from small- est to largest size.
  • Page 81: Rake Wall - With Base

    Rake Wall – With Base Find each stud size in a Rake Wall with a peak of 4 feet, a length of 8 feet, and a base of 5 feet. Use 16 inches as your on-center spacing. Rise = 4’ Base = 5’...
  • Page 82: Roofing Materials

    ROOFING MATERIALS Roof Covering — Bundles of Roof Shingles available on LT and Trig Plus III) How many bundles of roof shingles will you need for a 10-inch pitch roof covering a floor area of 14 feet by 11 feet? Keystroke 1.
  • Page 83: Roof Covering - Number Of Shingles

    Roof Covering — Number of Shingles You’re going to use 12-inch wide by 36-inch long asphalt (strip) shin- gles with 5-inch weather exposure. How many shingles are required for a roof measuring 1,745 square feet? Add a 10% waste allowance. þ...
  • Page 84: Area For Roofing Materials

    Area for Roofing Materials Find the number of roofing rolls needed to cover a roof with a 5/12 pitch, an overall span of 27 feet and a length of 34 feet 6 inches. The rolls measure 25 square feet each. Keystroke For the Handheld and Desktop: 1.
  • Page 85: Stair Layout Examples

    STAIR LAYOUT EXAMPLES STAIR LAYOUT DEFINIT IONS Rise: The “floor-to-floor” or “landing-to-landing” rise is the actual vertical rise required for building a stairway after the finish flooring has been in- stalled. Run: The run of a stairway is the amount of horizontal space required. The total run of a stairway is equal to the width of each tread multiplied by the number of treads.
  • Page 86 Number of Risers: The number of risers includes both the first and the last riser of the stairway. Riser Overage or Underage: The riser overage or underage is the dif- ference between the “floor-to-floor” rise and the total height of all of the risers.
  • Page 87: Stairs - Given Floor-To-Floor Rise

    Stairs — Given Floor-to-Floor Rise You’re building a stairway with a total rise of 9 feet 11 inches. Your de- sired riser height is 7-1/2 inches and desired tread width is 10 inches. Find the riser height; number of risers; riser underage/overage; tread width;...
  • Page 88: Stairs - Given Rise And Run

    Stairs — Given Rise and Run You need to build a stairway with a floor-to-floor height of 10 feet 1 inch, a run of 15 feet 5 inches, and a nominal desired riser height of 7- 1/2 inches (default). Find all stair values. Keystroke 1.
  • Page 89: Stair Risers Only - Custom Height

    Stair Risers Only — Custom Height You’re building an access stairway for a client who can’t handle con- ventional-height stairs. If the total rise is 3 feet 9 inches and your de- sired riser height is approximately 5-1/2 inches, find the actual riser height, number of risers and underage or overage remaining.
  • Page 90: Baluster Spacing

    Baluster Spacing You are going to install a handrail at the top of a balcony. Your total span is 156 inches and you would like the space between the balus- ters to be about 4 inches. If each baluster is 1-1/2 inches wide, what is the exact spacing between each baluster? Keystroke 1.
  • Page 91: Number Of Studs

    NUMBER OF STUDS Find the number of 16-inch on-center studs needed for a wall with a length of 18 feet 7-1/2 inches. Keystroke 1. Divide length by spacing: [On/C][On/C] 18 [Feet] 7 [Inch] 1 [ / ] 2 [÷] 16 [Inch] [=] 2.
  • Page 92: Trigonometry And D:m:s Examples

    TRIGONOMETRY AND D:M:S EXAMPLES PRACTICAL TRIGONOMETRIC FORMULAS The drawing and formulas below illustrate practical trigonometric applications: a = 53.1301° C = 5 ft A = 3 ft B = 4 ft b = 36.8699° Given side A and angle a, find: Side C A [÷] a [Cos] [=] (i.e., 3 [Feet] [÷] 53.13 [Cos] [=])
  • Page 93: Converting Degrees:minutes:seconds

    Converting Degrees:Minutes:Seconds Convert 23 42’39” to decimal degrees: Keystroke [On/C] [On/C] 23 [ ] 42 [ ] 39 [Conv] [ ] (d:m:s) Convert 44.29 to degrees:minutes:seconds format: Keystroke [On/C] [On/C] 44.29 [Conv] [ ] (d:m:s) þ þ Note: Improperly formatted entries will be redisplayed in the correct convention after any operator key is pressed.
  • Page 94: Time Calculations Using D:m:s

    [On/C] [On/C] 35 [%] [Conv] [Tan] [Conv] [ þ þ *Note: Your calculator may already show the answer in decimal degrees prior to pressing [Conv]. Simply press [Conv] [ toggle between desired decimal degree or d:m:s formats. Calculators without trigonometric functions:...
  • Page 95: Converting Tangent/Pitch To Angle

    Converting Tangent/Pitch to Angle Find the angle and corresponding tangent for a roof with an 8/12 pitch. Keystroke 1. Enter pitch: [On/C] [On/C] 8 [Inch] [Pitch] 2. Convert pitch to degrees: [Pitch] 3. Find tangent:* [Tan] *For LT, Handheld and Desktop: Press [Conv] [Pitch] to obtain same result.
  • Page 96: Angle - Rise And Hypotenuse Known

    Angle — Rise and Hypotenuse Known (Trig Plus III and Desktop Only) Find the angle that connects the rise and hypotenuse of a right trian- gle, if the rise is 6 feet and the hypotenuse is 10 feet in length. Keystroke 1.
  • Page 97: Appendix A - Default Settings

    “Metric Mode,” where settings or answers are defaulted to the above metric values. To set the calculator to Metric Mode, press the digit [1] key while turning the calculator on. To return to Impe- rial Mode, repeat this procedure.
  • Page 98: Appendix B - Preference Settings

    The options vary per model. þ þ Note: * = Default Setting or the setting calculator defaults to upon performing an All Clear [Conv] [x]. Preference 1) Fractional Resolution...
  • Page 99 (Cont’d) Preference 3) Volume Display Format (n/a for Metric Mode) 4) Rake Wall Descending or Ascending 5) Jack Rafters Descending or Ascending (n/a for LT model) 6) Jack Rafters O-C or Mate (n/a for LT model) 7) Fraction Standard or Con- stant Options Standard (if units entered are the same—...
  • Page 100 (Cont’d) Preference 8) Exponent Off or On 9) Meter Linear Display 98 — CONSTRUCTION MASTER PRO Options Off (Exponential Mode is Off; turns on Auto-ranging; i.e., if display can’t show seven digits, will display in next largest unit). On (Exponential Mode is On - *Default for Trig Plus III) 0.000 (linear meter answers always displayed to third decimal place) 0.
  • Page 101: How To Set Preferences

    How to Set Preferences The following sections detail Preference Setting options for the Con- struction Master Pro calculators. Enter the Preference Mode by pressing [Conv] [Stor] (Prefs). Access each category by pressing the [Stor] key until you reach the desired setting.
  • Page 102: Lt (#4030)

    LT (#4030) To Set “Fractional Resolution”: [Conv] [Stor] (Prefs) (1st press of [Stor]) [+] (plus sign) To Set Rake Wall Stud Sizes to “Descending” or “Ascending”: [Stor] (2nd press of [Stor]) [+] (plus sign) To Set “Area” Answer Format: [Stor] (3rd press of [Stor]) [+] (plus sign) To Set “Volume”...
  • Page 103: Handheld (#4060) And Desktop (#44060)

    Handheld (#4060) and Desktop (#44060) To Set “Fractional Resolution”: [Conv] [Stor] (Prefs) (1st press of [Stor]) [+] (plus sign) To Set “Area” Answer Format: [Stor] (2nd press of [Stor]) [+] (plus sign) To Set “Volume” Answer Format: [Stor] (3rd press of [Stor]) [+] (plus sign) To Set Rake Wall Stud Sizes to “Descending”...
  • Page 104 (Cont’d) To Set “Meter” Linear Decimal Format: [Stor] (9th press of [Stor]) METR 0.000 M [+] (plus sign) METR 0. M þ þ Note: Press [On/C] at any time to exit the Preference Mode. 102 — CONSTRUCTION MASTER PRO...
  • Page 105: Trig Plus Iii (#4075)

    Trig Plus III (#4075) To Set “Fractional Resolution”: [Conv] [Stor] (Prefs) (1st press of [Stor]) [+] (plus sign) To Set “Area” Answer Format: [Stor] (2nd press of [Stor]) [+] (plus sign) To Set “Volume” Answer Format: [Stor] (3rd press of [Stor]) [+] (plus sign) To Set Rake Wall Stud Sizes to “Descending”...
  • Page 106 (Cont’d) To Set “Exponential Mode” On or Off: [Stor] (8th press of [Stor]) EXP On [+] (plus sign) EXP OFF To Set “Meter” Linear Decimal Format: [Stor] (9th press of [Stor]) METR 0.000 M [+] (plus sign) METR 0. M þ...
  • Page 107: Appendix C - Using The Desktop Printing Model (Dt Printer: #44065)

    See the instructions below. PRINTER KEYS [Off—On—Print] — Power Switch Switch that turns the printer and calculator on and off. This power switch is located in the upper left. “Off” - Power Off: move switch to far left.
  • Page 108 ] — Paper Feed Press this key to advance the printer paper. Note of Caution: When your printing paper is running low (you are nearing the end of the roll), the paper may curl back into the feeder and jam (see “A”). The proper feed is shown below (see “B”). It is therefore best to replace the paper before this can occur.
  • Page 109 (e.g., [Stair] key) is pressed. [Conv] [ x ] [ x ] — All-Clear/Full Reset Clears/resets the calculator back to its default settings. Use this only with caution, as it will erase any custom Preference settings you have programmed.
  • Page 110: Connecting The Ac Adapter

    CONNECTING THE AC ADAPTER Your calculator operates on AC power so you don’t have to use batter- ies. To connect the AC adapter, first make sure your calculator is turned off (power switch to “Off”). Then, plug the AC power plug into a power outlet (Step 1) and plug the connecting end into the small outlet at the end base of your calculator (Step 2), as shown.
  • Page 111: Using Battery Power

    RadioShack, or any store that sells batteries. Batteries: Four AA batteries 1. Switch power to “Off.” 2. Turn calculator over and remove the battery cover by sliding it in the direction of the arrow. See (1) on fig- ure below.
  • Page 112: Replacing The Paper Roll

    See (A) on next page. 2. Insert the leading edge of the paper roll into the slit lo- cated on the back of the calculator. See (B) on next page. 3. Turn the power on (switch to Print Mode or “Print”).
  • Page 113 User's Guide — 111...
  • Page 114: Replacing The Ink Roller

    REPLACING THE INK ROLLER You can purchase a replacement ink roller from CI at www.calculated.com or by calling 1-800-854-8075. (CI product number 5002-IR1) 1. Move the power switch to “Off.” 2. Remove the plastic print cover. See (A) on next page.
  • Page 115 User's Guide — 113...
  • Page 116: Notes On Using The Printer

    [Stair] key. Setting Your Calculator to Auto-Print You must have your calculator set to “Print,” or switched to Printing Mode (using the power switch), in order to use auto-printing. The Pref- erence Setting must also be set to “Print List On.” (Default is “Off”).
  • Page 117 [Conv] [=]. Note: You do not have to access the Preference Setting or even be in Print Mode to use this setting; the calculator will automatically print regardless of whether your calculator is set to Print or On. [Conv] [=] — Print List Prints the entire list of values in a repetitive-solution problem (e.g.,...
  • Page 118 Annunciators Some annunciators will print differently than those viewed on the calcu- lator display while in non-printing mode, or on the display of the non- printing Construction Master Pro desktop and other Construction Mas- ter Pro models. See the table below for a list of these annunciator dif- ferences: Construction Master Pro DT...
  • Page 119: Appendix D - Important Notes For Owners Of Previous Construction Masters

    APPENDIX D — IMPORTANT NOTES FOR OWNERS OF PREVIOUS CONSTRUCTION ® MASTERS If you are an owner of a previous Construction Master calculator, the following list will help you compare several new or enhanced features available on selected Construction Master Pro calculators. New/Enhanced Function...
  • Page 120 (Cont’d) New/Enhanced Function Preference Settings Rake Wall Rafter Cutting Angles Stairs Weights 118 — CONSTRUCTION MASTER PRO Description Dimensional formats for calculated areas and vol- umes may be set to display in preferred formats (e.g., sq. feet, cu. yards). Also, Jack rafters and Rake Wall stud sizes may be set to display in either ascending or descending order.
  • Page 121: Appendix E - Accuracy, Auto Shut- Off, Batteries, Errors

    Each calculation is carried out internally to ten digits. Errors — When an incorrect entry is made, or the answer is beyond the range of the calculator, it will display the word “ERROR.” To clear an error condition you must hit the [On/C] button once. At this point you must determine what caused the error and re-key the problem.
  • Page 122: Auto Shut-Off

    Note: Please use caution when disposing of your old battery, as it contains hazardous chemicals Replacement batteries are available at most discount or electronics stores. You may also call Calculated Industries at 1-775-885-4975. Battery Replacement Instructions Construction Master Pro DT (Desktop) Model (#44060): To replace the battery, use a small Phillips’...
  • Page 123: Reset Key

    Reset Key If your calculator should ever “lock up,” press Reset—a small hole lo- cated to the left (or right for the Construction Master Pro Desktop or Desktop Printer) of the [Off] key—to perform a total reset.
  • Page 124: Appendix F - Area/Volume Formulas

    APPENDIX F — AREA/VOLUME FORMULAS Area Formulas 122 — CONSTRUCTION MASTER PRO...
  • Page 125: Surface Area/Volume Formulas

    Surface Area/Volume Formulas User's Guide — 123...
  • Page 126: Repair And Return

    4. If you need more assistance, please go to our website at www.calculated.com and click on Support, then Repair Services FAQs. 5. If you believe you need to return your calculator, please speak to a Calculated Industries representative for additional information! Call Toll Free: 1-800-854-8075...
  • Page 127: Warranty

    SULTING FROM MISUSE OR ABUSE. To obtain warranty service in the U.S., ship the product postage paid to Calculated Industries (address listed on page 126). Please provide an explanation of the service requirement, your name, address, day phone number and dated proof of purchase (typically a sales receipt). If the product is over 90 days old, include payment of $6.95 for return ship-...
  • Page 128 Repair Service – Outside the U.S.A. To obtain warranty or non-warranty repair service for goods purchased outside the U.S., contact the dealer through which you initially pur- chased the product. If you cannot reasonably have the product repaired in your area, you may contact CI to obtain current product repair infor- mation and charges, including freight and duties.
  • Page 129: Legal Notes

    Legal Notes Software copyrighted and licensed to Calculated Industries by Construction Master Technologies, LLC, 2003. User’s Guide copyrighted by Calculated Industries, Inc., 2003. ® Construction Master and Calculated Industries marks of Calculated Industries, Inc. ALL RIGHTS RESERVED Designed in the U.S.A.
  • Page 130: Index

    INDEX Accuracy/Errors, 119 Adding Linear Measurements, 39 Angle — Rise and Hypotenuse Known, 94 Angle and Diagonal (Hypotenuse), 67 Arc Length, 52 Arched Windows, 51 AREA CALCULATIONS, 41 Area for Roofing Materials, 82 Area, Rectangular, 41 Area, Square, 41 AREA/VOLUME, 122 Auto Shut-Off, 120 Baluster Spacing, 88 Basic Math with Dimensions, 32...
  • Page 131 Seconds, Converting, 91 Dimensional Measurement Unit Keys, 13 Dimensions (Linear), Entering, 27 Dimensions (Square/Cubic), Entering, 27 Dimensions, Adding, 32 Dimensions, Dividing, 33 Dimensions, Multiplying, 32 Dimensions, Subtracting, 32 Entering Dimensions, 27 Error Codes, 119 EXAMPLES, 38 FLOOR COVERING AREA CALCULATIONS, 60 GRADE/SLOPE, 61 Grade/Slope, Percent, 92 Hip/Valley and Jack Rafter Keys...
  • Page 132 NOTES: 130 — CONSTRUCTION MASTER PRO...
  • Page 133 Construction Master Pro Construction Master Pro LT Trig Plus III Model 4030 Model 4075 Construction Master Pro DT (Desktop model) Model 44060...
  • Page 134 Designed in the United States of America Printed in China Manual UG4060E-D...

Table of Contents