Interactive Function Manual CMOS Sensor Contents of the Accessory Bag..............i Accessories Introduction................ii Operation Guide for Windows OS ............1 Operation Guide for Mac OS ..............12 Troubleshooting ..................18...
Contents of the Accessory Bag Please make sure that following items are included in the Accessory Bag. If any items are missing, contact your dealer. 1. Accessory Bag 2. Pointer 3. Light Pen 4. Batteries (AA) 5. Batteries (AAA) 6. Hanging String...
Accessories Introduction Contents of the Accessory Bag Function Key on the "Pointer Body" LED Lamp Button: Mouse Left Key Before using the Pointer. Screw the Rod part into the pointer body firmly please. How to use this While pressing the button Infra Red signal is emitted from the tip of the rod and the CMOS sensor in the projector detects the position of it.
Page 4
Contents of the Accessory Bag Accessories Introduction Function Key on the "Light Pen" Touch sensor pen tip LED Lamp Button: Mouse Left Key How to use this While the button is pressed or the tip is pressed to a hard screen Infra Red signal is emitted from the tip of the pen and the CMOS sensor in the projector detects the position of it.
Operation Guide for Windows OS Interactive function is provided by "LightPen" software. 1. System Requirements To ensure the interactive function work properly, please check your computer to see if it meets the following conditions. System Requirements OS Required Microsoft Windows 2000(SP4)/XP(SP2)/Vista Processor Type Intel Pentium IV or above 256 MB above...
Page 6
Operation Guide for Windows OS Note for Windows Vista (a) Click mouse right key on "LightPen.exe" or the short-cut icon for "LightPen.exe" and then click mouse left key to select "Properties". LightPen Software for Windows LightPen.exe LightPen System Play Send To Properties...
Page 7
Operation Guide for Windows OS (b) Select "Compatibility" sheet and add check marks to the following. "Run this program in compatibility mode for: Windows XP (Service Pack 2)", "Disable desktop composition". Then select "Apply".
Page 8
Operation Guide for Windows OS 3. Initial Setup for Interactive Function 3.1 Connect supplied USB cable between XIP2600 and the PC. 3.2 Execute "LightPen" software by double-checking the "LightPen. exe" or the short-cut icon for the "LightPen.exe". Then the icon for "LightPen"...
Page 9
Operation Guide for Windows OS Step 3: Choose the projection distance from pop-up menu (>3m,>2m,<2m), and then select "OK". 3.4. Calibration Step 1: Click mouse right key on "LightPen" in the task bar. Step 2: Select "Calibration". Step 3: According to the projector setting condition, select projection method of "Desktop"or "Ceiling".
Page 10
Operation Guide for Windows OS 3.4 Calibration Step 4: Push the button on the "Pointer" or "Light Pen" (pending on the screen size) while placing the tip on the center of green target. The color of target changes black from green. Then next green target appears on the upper middle area of the screen.
Page 11
Operation Guide for Windows OS 4. How To Use Interactive Function Function of each icon in the Tool bar Tool bar position To position tool bar on the right or left side of screen. Mouse To change function to Computer Mouse. To change function to Pen.
Page 12
Operation Guide for Windows OS 4. How To Use Interactive Function In the Mouse mode(default) Mouse pointer can be moved by the Pointer or the Pen. The left click or double click can be done by pushing the button. The right click can be done as follows. At first place the mouse pointer on the target.
Page 13
Operation Guide for Windows OS 4. How To Use Interactive Function In the Pen mode A line can be drawn with the Pointer or the Pen. In order to continue to emit IR light from the tip, press and hold the button on the Pointer during drawing please.
Page 14
Operation Guide for Windows OS 5. How to finish Interactive function 5.1 Select "Mouse" mode by selecting "Mouse" icon in the tool bar. 5.2 Click mouse right key on LightPen Icon in the task bar.
Page 15
Operation Guide for Windows OS 5.3 Click mouse left key to select "Exit". 5.4 Click mouse left key to select "OK" in the confirmation dialog. (This can be down either on the screen or on the PC.)
Operation Guide for Mac OS Interactive function is provided by "LightPen" software. 1. System Requirements To ensure the interactive function work properly, please check your computer to see if it meets the following conditions. System Requirements OS Required Mac OS X v10.4.11- v10.5 or above Intel processor or Power PC Processor Type 512 MB RAM or above...
Page 17
Operation Guide for Mac OS 3. Initial Setup for Interactive Function 3.1 Connect supplied USB cable between XIP2600 and the PC. 3.2 Execute "LightPen" software by clicking the "LightPen" or the short- cut icon for the "LightPen". Then the icon for "LightPen" appears in the task bar and the tool bar appears on the right side of the screen.
Page 18
Operation Guide for Mac OS Step 3: Choose the projection distance from pop-up menu (>3m,>2m,<2m), and then select "OK". 3.4 Calibration Step 1: Click mouse key on "LightPen" in the task bar. Step 2: Select "Calibration".
Page 19
Operation Guide for Mac OS Step 3: Push the button on the "Pointer" or "Light Pen" (pending on the screen size) while placing the tip on the center of green target. The color of target changes black from green. Then next green target appears on the upper middle area of the screen.
Page 20
Operation Guide for Mac OS 4. How To Use Interactive Function Function of each icon in the Tool bar Tool bar position To position tool bar on the right or left side of screen. Mouse To change function to Computer Mouse. To change function to Pen.
Page 21
Operation Guide for Mac OS 4. How To Use Interactive Function In the Mouse mode(default) Mouse pointer can be moved by the Pointer or the Pen. The left click or double click can be done by pushing the button. The right click can be done as follows. At first place the mouse pointer on the target.
Page 22
Operation Guide for Mac OS 4. How To Use Interactive Function In the Pen mode A line can be drawn with the Pointer or the Pen. In order to continue to emit IR light from the tip, press and hold the button on the Pointer during drawing please.
Page 23
Operation Guide for Mac OS 5. How to finish Interactive function 5.1 Select "Mouse" mode by selecting "Mouse" icon in the tool bar. 5.2 Click on LightPen Icon in the task bar , and choose "Exit" to exit from the program.
Troubleshooting 1. Q: Why does it show “No LightPen found”? A: Reasons for this might be: (1) In case of Windows OS, if the following image (A) pop up, it indicates that USB cable is not connected or the USB port is out of order.
Page 25
Troubleshooting 2. Q: Why I cannot execute calibration on the green cross target? A: (1) Please check if "Pointer" or "Light Pen" works: (1-1) Please check if "Pointer" or "Pen" battery is low or battery cap is loose. (1-2) When using "Pointer" or "LightPen", be sure to locate the tip of the "Pointer"...
Page 26
Troubleshooting (3) The image resolution has been changed. Running the calibration procedure again will solve the problem. 4. Q: Why is the cursor jumping? A: This may be caused by strong ambient light interference. Try to avoid strong ambient light interference, especially strong sun light directly projected on the screen.
Page 27
Troubleshooting Note: Always use alkaline batteries for the "Pointer" and "Light Pen".
Page 28
U.S.A. Canada EIKI International, Inc. EIKI CANADA - Eiki International, Inc. 30251 Esperanza P.O. Box 156, 310 First St. - Unit 2, Rancho Santa Margarita Midland, ON, L4R 4K8, Canada CA 92688-2132 Tel: 800-563-3454 (705)-527-4084 U.S.A. Fax: 800-567-4069 (705)-527-4087 Tel: 800-242-3454 (949)-457-0200 E-Mail: canada@eiki.com...