Table of Contents
Advertisement
12.0 - PROGRAMMING
Only expert users should modify these settings to avoid malfunctions of the parking
!
!
Supply the display (turn
"ON"
the vehicle
!
Press and keep pressed for more than two seconds one of the two push-buttons on the display; the
previous programming mode will be displayed
F: Factory, standard adjustment , "Factory parameters".
C: Custom, user-chosen adjustment, "Custom Parameters".
Press the left push-button to go to the next
parameter.
When the parameter you want to modify is displayed, press one of the push-buttons and keep it
pressed until the display starts to blink; at this point you can modify the parameter.
Press the left push-button to increase the value
of the parameter (
the letter "C" will be displayed
when parameter has been modified
Press one of the two
push-buttons
on the control unit and keep it pressed for at least two seconds
to register the value.
The display will stop blinking and the selected parameter will be displayed.
Cut supply to the display (turn off the vehicle) to exit the programming mode.
ress the two push-buttons on the display and keep them pressed for more than two
!
seconds to reset all the factory settings (F).
PAGE 12 - INSTALLER MANUAL
system.
ignition key).
.
Press the right push-button to go to the
previous parameter.
Press the right push-button to decrease the
value of the parameter (
the letter "C" will be
).
displayed when parameter has been modified
13.0 - SETTING OF PARAMETERS
Nr.
PARAMETER
01
Volume of buzzer
02
Detection range of front central sensors
03
Detection range of rear central sensors
04
Detection range of sides sensors
05
STOP zone of front sensors
06
STOP zone of rear sensors
07
Audible warning for front obstacles
08
Mounting of front control unit
09
Mounting of rear control unit
10
Display colour
11
Suppression of spare wheel indication
12
Number of speed signal pulses
13
Delay of front sensors deactivation
14
Service display (testing)
15
Connection of odometer wire
16
Front sensors sensitivity to detect obstacles
17
Rear sensors sensitivity to detect obstacles
Ref.1
: 0 deactivated, 1 low, 2 high.
Ref.2
: 0 c
ontinuous detection of obstacles (only if vehicle or obstacle is moving), 1 continuous
detection of obstacles (even if vehicle or obstacle is not moving
Ref.3
: 0
standard detection (sensors position 1-2-3-4), 1 inverted detection (sensor position
Ref.4
: 1 red, 2 green, 3 blue, 4 amber, 5 white.
Ref.5
: by setting "0" the system can only be deactivated with the push-button on the left-hand side of
the display; automatic deactivation occurs when speed exceeds 15 km/h (operation via the
odometric pulse). By setting a different value, the sensors are deactivated according to the set
).
time delay and if there are no obstacles in front of vehicle).
Ref.6
: not activated, 1 wireless communication test, 2
audible alert
", 3
learning of speed pulses only if the odometer cable is connected to the
), 4 d
display
isplay of software version (small number on display
Ref.7
: 0 c
onnection of display cable
Ref.8
: 1 low, 2 standard, 3 high.
14.0 - WARRANTY CONDITIONS
This product is guaranteed to be free from defects in workmanship for a period of 24 months from the
date of installation reported on this warranty, in compliance with the 1999/44/CE Warranty Directive
(L. D. N° 24 of the 02/02/2002).
Please fill-in entirely the guarantee certificate included in this booklet and DO NOT REMOVE the
guarantee label from the device.
The warranty will become void if labels are missing or torn, if the installation certificate is not fully
compiled or if the enclosed sale document is missing.
The warranty is valid exclusively at authorized Gemini Technologies centers.
The manufacturer declines any responsability for eventual malfunctions of the parking sensors or any
damage to the vehicle electrical system due to improper installation, use or tampering.
The parking system is strictly a parking assist device, it should not be considered to be a safety device
for any purpose.
RANGE
0, 1, 2 (
Ref.1
)
From 50 to 95 cm
Not used
From 50 to 95 cm
From 35 to 50 cm
Not used
0, 1 (
Ref.2
)
0, 1 (
Ref.3
)
Not used
1, 2, 3, 4, 5 (
Ref.4
Not used
From 1.0 to 25.0
0 or from 10 to 60 sec. (
0, 1, 2, 3, 4 (
Ref.6
0,1 (
Ref.7
)
1, 2, 3 (
Ref.8
)
Not used
).
speed indication and activation of "overspeed
(
).
, 1 c
onnection of front control unit cable
.
INSTALLER MANUAL - PAGE 13
SETTING
2
80
---
60
35
---
0
0
---
)
3
---
3.0
Ref.5
)
0
)
0
0
2
---
4-3-2-1).
Advertisement
Table of Contents
