Gemini 514 User Manual
Gemini 514 User Manual

Gemini 514 User Manual

Wired rear parking sensor kit

Advertisement

 
     
 
UK
 
Installation and configuration tasks should only be performed by qualified personnel.
The parking system is designed as a parking assist device only, it should not be considered to replace care and attentiveness while
maneuvering. Always check your wing mirrors and rear view mirror while reversing and keep a slow speed to avoid unexpected hazards.
The system comes with 4 compact waterproof sensors that can be spray painted to color match the shade of your bumper. The parking sensors can be
configured, by a Gemini authorized Service Center, to your preference and be set up so as not to be impeded by a rear mounted spare tire/tow bar.
The system is automatically activated when ignition is turned ON and reverse gear is engaged. Two consecutive beeps will confirm activation. Detection of
obstacles will be signaled by the buzzer. The audible warning with a series of beeps will increase in pitch and frequency as the vehicle moves nearer a stationary
object: the faster the beeping the closer the obstacle. The beeps become a continuous solid tone when the preset minimum safety distance (STOP zone) is
reached.
 Tow Bar/Rear Spare Tire Configuration
When a vehicle has a tow bar or a rear spare tire, the control module can be configured to push out the impact detection zone past the accessory. The control
module must be configured by an authorized Service Center.
CAUTION: OBSTACLES BETWEEN THE BUMPER AND THE NEW STOP ZONE WILL NOT BE DETECTED.
 Trailer Recognition
Trailer recognition mode automatically disables the rear sensors when towing with trailer plug connected (contact an authorized Service Center). When reverse
gear is engaged, 3 Bops will confirm deactivation of all sensors.
SENSOR DETECTION INFORMATION
Certain conditions may affect the ability of the sensor to correctly detect obstacles:
1.
Presence of human beings, animals or small obstacles or objects/materials with low reflectance might not be detected by the parking system.
2.
In case of heavy rain or snow the parking system might give an audible alert even if no obstacles are present: this does not necessarily indicate that
the parking system is defective.
3.
If the sensors are covered with mud, ice or snow (normal function resumes after cleaning or defrosting).
4.
An extremely bumpy road or an incline, gravel or grass.
5.
Vehicle horns, motorcycle engines, air brakes of large vehicles or other loud noises producing ultrasonic waves.
6.
Heavy rain or splashes on the sensors and water puddles.
7.
Obstacles located below the bumper will not be detected when they are in close proximity.
BASIC MAINTENANCE TIPS
When cleaning the sensors take special care not to scratch or damage the surface: carefully clean the sensors with a soft cloth.
In car washes which use steam jet or high-pressure washers, keep the nozzle at least 10 cm away from the sensors.
SENSOR FAILURE INDICATION
When reverse gear is engaged, the parking sensor system provides an instant, automatic, self-diagnostic function. If all the sensors are operative, 2 Beeps will
confirm activation. If one of the sensors is faulty or disconnected, a deep error tone (Bop) will sound followed by the number of beeps corresponding to the faulty
sensor. The cycle will repeat until all faulty sensors have been signaled. 2 Bops will confirm the end of the self-test cycle.
The system will exclude any faulty sensor and keep the other ones active. The following is an example of error indications:
Sensor 1 inoperative => 2 activation Beeps + 1 Bop + 1 Beep + 2 closing Bops.
Sensors 1 and 2 inoperative => 2 activation Beeps + 1 Bop + 1 Beep + 1 Bop + 2 Beeps + 2 closing Bops.
This product is guaranteed to be free from manufacturing defects for a period of 24 months from the installation date shown on the warranty certificate, in
compliance with Directive 1999/44/CE L.D. N. 24 dated 02/02/2002.
Please fill-in entirely the warranty certificate that accompanies the product and DO NOT REMOVE the bar code warranty label from the device. The warranty will
become void if labels are missing or torn, if the warranty certificate is not fully compiled or if the enclosed sales document is missing.
The warranty is valid exclusively at authorized Gemini Technologies S.p.A. Service Centers.
The manufacturer declines any responsibility for eventual malfunctions of the device or any damage to the vehicle electrical system due to improper installation,
use or tampering.
WIRED REAR PARKING SENSOR KIT 514
HOW THE SYSTEM WORKS
WARRANTY CONDITIONS
1/10
 
Rev.01 09/2015

Advertisement

Table of Contents
loading

Summary of Contents for Gemini 514

  • Page 1 The system comes with 4 compact waterproof sensors that can be spray painted to color match the shade of your bumper. The parking sensors can be configured, by a Gemini authorized Service Center, to your preference and be set up so as not to be impeded by a rear mounted spare tire/tow bar.
  • Page 2: Kit Contents

    WIRED REAR PARKING SENSOR KIT 514 KIT CONTENTS            4x cable clips     1x buzzer 1x control unit (ECU) 4x sensors 1x wire harness 10x zip-ties         4x 10° angled 4x standard external  ...
  • Page 3: Installation Precautions

    INSTALLATION PRECAUTIONS  Installation and connections should only be done by qualified personnel.  Disconnect the negative pole of the battery before connecting any wire.  Some bumpers have factory markings on the inner side; before drilling any holes, make sure they correspond to the recommended positions.
  • Page 4: Installation

    INSTALLATION Control unit and buzzer  Position the control unit in the luggage compartment, in a dry place, away from water infiltrations.  Mount the buzzer with the supplied double-faced adhesive tape or screws where the driver will clearly hear the audible signals. ...
  • Page 5: Electrical Connections

    Connect the sensors to the wires coming out of the trunk (the longest wires at the opposite end of the factory grommet). SENSOR POSITIONING Space out the supplied adhesive cable clips along the bumper, insert the cable ties and secure the wires in place. Bundle up any excess cables. NB: Keep all wires away from high temperature components (ex.
  • Page 6 PARKING SYSTEM AUDIBLE SIGNALS When reverse gear is engaged, the parking sensor system provides an instant, automatic, self-diagnostic function. If all the sensors are operative, 2 Beeps will confirm activation. In case one of the sensors is faulty or disconnected, a deep error tone (Bop) will sound followed by the number of beeps corresponding to the faulty sensor. The cycle will repeat until all faulty sensors have been signaled.
  • Page 7: Parameter Setup

    PARAMETER SET-UP  Before configuring the parking sensors, ensure all connections have been done properly.  Parameters must only be configured by qualified personnel. System configuration is done by pressing buttons “A” and “B” (see figure below) or via a user-friendly PC software: ...
  • Page 8 (allows the system to see past the obstruction) 20 cm 30 cm * A user friendly PC software (soon available at: www.gemini-alarm.com) will allow more flexibility in programming the parameters. The dedicated interface will also allow reading and overwriting previously configured parameters. 8/10...
  • Page 9 SENSOR FITTING AND OBSTACLE DETECTION Correct Position: height, inclination and √ orientation are correct.* Sensors are excessively turned upwards => low obstacles are not detected. Sensors are excessively turned downwards => false alarms due to ground detection. Sensors fitted too low => false alarms due to ground detection.
  • Page 10: Troubleshooting

    TROUBLESHOOTING FAULTS CAUSE / SOLUTIONS Check that the cable connectors from the sensors are correctly fitted to the control unit. The system does not work when reverse gear is Check that the arrow and the UP indication are pointing upwards. engaged.

Table of Contents