Table of Contents
Advertisement
Quick Links
INSTALLATION CERTIFICATE
The undersigned qualified installer attests to have personally fitted the here described system following the
manufacturer instructions.
By :
Sold on :
.................................................................
Car :
..........................................................................................................................
GEMINI Technologies S.p.A.
Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia
Tel. +39 0332 943211 - Fax +39 0332 948080
Web site: www.gemini-alarm.com
Type of product :
814FWH
Reg. n.532-A
UNI EN ISO 9001:2008
KIT Parking
Sensor 814FWH
INSTALLATION AND
USE MANUAL
UK
AC 2876/UK Rev. 00 - 01/12
Advertisement
Table of Contents
Related Manuals for Gemini 814FWH
Summary of Contents for Gemini 814FWH
- Page 1 INSTALLATION CERTIFICATE The undersigned qualified installer attests to have personally fitted the here described system following the manufacturer instructions. By : KIT Parking Sensor 814FWH Type of product : Sold on : 814FWH ..............INSTALLATION AND USE MANUAL Car : ..........................
- Page 2 Sensor 1: front with shortest cable. Sensor 4: front with longest cable. BROWN POWER POWER BROWN km/h +12/24V BLACK-YELLOW km/h BLACK-BLUE BROWN 10 x...
- Page 3 WINDSCREEN CORRECT POSITION DASHBOARD ALTERNATIVE MOUNTING TECHNICAL SPECIFICATIONS Supply voltage From 9 to 30 Vdc Current consumption when system working 100mA max. Service temperature range From -20°C to +70°C Ultrasound frequency 40Khz Control units and display communication frequency 434Mhz Software version reference (reported on control unit and display) SW07...
-
Page 4: Table Of Contents
USER MANUAL CONTENTS 3.0 - SYSTEM OPERATION - PRELIMINARY ADVICE.................... PAGE 02 - WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) DIRECTIVE..PAGE 02 USER MANUAL Remember to always look around the vehicle while parking. Small obstacles or objects with low reflectance might not be detected. - SYSTEM OPERATION.................... -
Page 5: Troubleshooting Guide
3.2 - A UTOMATIC ACTIVATION OF SENSORS (odometer signal 4.0 - TROUBLESHOOTING GUIDE Front sensors are activated whenever ignition is turned ON and are automatically deactivated when 4.1 - LOW POWER SUPPLY SIGNAL speed exceeds about 15Km/h If, when the system is turned on, the battery level is too low to guarantee the accuracy of the system, after a few seconds, the following icons will be displayed: vehicle, front sensors arrow icon and four On some vehicles, when speed exceeds 15Km/h, no icon could be displayed even front detection zones closest to the bumper. -
Page 6: Display
INSTALLER MANUAL 5.0 - DISPLAY 7.0 - INSTALLATION OF SENSORS The following icons will be displayed according to operations. To install the sensors on a metal bumper, you must use appropriate adapters ( supplied) DISTANCE OF OBSTACLE FRONT SENSORS INDICATOR DETECTION ZONES PARAMETER. -
Page 7: Connections
8.0 - CONNECTIONS Use the supplied tie (13) or bolts (3) to secure the control units to the front bumper. +12V Clean thoroughly the plastic brackets (7 or 8) and around the holes, apply “PRIMER” (14), let dry for at least one minute and then proceed as follows. +18°C Check the wireless communication and the length of the cables before proceeding with the final positioning of the accessories. -
Page 8: Pairing Of Control Unit With Display
9.0 - PAIRING OF CONTROL UNIT WITH DISPLAY 11.0 - TESTING Turn the ignition key “ON”. When pairing, make sure no similar control units are activated in the ress and keep pressed one of the two push-buttons on the display until the system enters the surroundings. -
Page 9: 12.0 - Programming
The warranty is valid exclusively at authorized Gemini Technologies centers. seconds to reset all the factory settings (F).