Savant IRX-LN01 Quick Reference Manual

SmartLink 3-Gang Receiver Wall Plate (IRX-LN01)
Quick Reference Guide
Box Contents
(1) Smart Link 3-Gang Receiver Wall Plate (IRX-LN01)
(1) Install Kit (075-0147-xx)
(1) Faceplate for HDBaseT RX Box (071-0820-xx)
(1) 4-pin Screw down Connector (028-9395-xx)
(4) Mounting Screws – Philips Flat (039-0103-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Temperature 32° to 104° F (0° to 40°C)
10% to 90% Relative humidity (non-
Humidity
condensing)
Dimensions
Without Faceplate
Height 4.52 in (11.48 cm)
Width 6.35 in (16.12 cm)
Depth 2.31 in (5.87 cm)
Net: 0.8 lb (0.36 kg)
Weight
Shipping: 1.75 lb (0.79 kg)
Power over Ethernet
Support
IEEE 802.3af
Standard
Nominal Power 6 W
Maximum Load 10 W
Regulatory
Safety and
FCC Part 15 | CE Mark | C-Tick
Emissions
RoHS Compliant
Minimum Supported Release
Savant OS da Vinci 5.2.1
IMPORTANT: Although HDBaseT transmission technology is much less
susceptible to EMI interference than other transmission technologies,
if possible, Savant recommends that you use shielded Cat5e/Cat6
cable with this product and shielded metal RJ-45 connectors with a
drain wire soldered to the connector for maximum reliability. Shielded
cable and connectors are also recommended to safeguard against
any unpredictable environmental electrical noise which may impact
performance at resolutions above 1080p.
The IRX-LN01 also provides control capabilities for common AV
functions for controlling other devices in the room with two serial
and two IR ports. The unit also contains two Ethernet ports for
connecting local equipment, such as computers, to the local area
network (LAN) for added flexibility.
The IRX-LN01 does not require a local power supply as it is remotely
powered via Power over Ethernet from any IEEE 802.3af compliant
PoE switch.
IRX-LN01 | 009-0908-02 | 160706
Copyright © 2016 Savant Systems, LLC
With Faceplate
4.72 in (11.99 cm)
6.55 in (16.64 cm)
2.4 in (6.10 cm)
Front Panel
HDMI Type A output provides HDMI audio
and video output at video resolutions to
HDMI Out
1080p@60hz and graphics resolutions to
1920x1200@60Hz.
TosLink In Reserved for future use.
RJ-45 ports used to transmit serial binary
RS-232
data.
Reset Push button used to reset Static IP Address
Reserved Reserved for future use.
10/100 Base-T auto-negotiating Ethernet
LAN ports.
Green (right) indicates an Ethernet speed
LAN of 100 Mb.
Off indicates an Ethernet speed of 10 Mb.
Green (left) indicates Ethernet data
activity.
Grounding terminal: optional use
Green indicates the Host has established
communications with the embedded
system.
Green blinking indicates the embedded
system is ready (running with DHCP IP
address), but the Host has not established
communications with the embedded
system.
Off indicates the embedded processor is
resetting or is powered up; and is booting
the embedded firmware.
CPU Status
Red indicates the Host has determined the
LED
firmware needs to be updated, but a
problem occurred during the process that
will initiate a reset.
Red blinking indicates the embedded
firmware is running, but has not received a
DHCP IP Address.
Amber indicates the Host is currently
updating the embedded firmware.
Amber blinking indicates the embedded
system has a valid link-local IP Address and
is waiting to connect to the Host.
Link Status Green indicates valid link.
LED Off indicates no link.
IR Infrared serial transmitter output ports.
45 Perseverance Way, Hyannis, MA 02601
For Product Info
Savant.com | 508.683.2500