Advertisement
Quick Links
Placement and Maintenance
Sequel™ Home Office Furniture is designed for indoor use on level floors. Clean
glass with glass cleaner, and steel parts and wood veneer with a moist cloth. Your
Sequel™ Home Office Furniture is engineered for easy assembly. Carefully follow this
procedure to prevent any damage.
Do not use power tools for assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly workspace should be a non-
marring surface such as carpet. For missing hardware pieces, please contact BDI
Customer Service at customerservice@bdiusa.com. For all other concerns, please
contact your BDI Retailer.
Component List
N - Upper Horizontal Beam x 1
C - Back Panel x 1
E - Lower Horizontal Beam x 1
Designed by Matthew Weatherly.
'Sequel' is a trademark of Becker Designed, Inc.
All rights reserved. ©2009 Becker Designed, Inc.
Made in Taiwan. 6001REV121409v5
S
equel
6001 D
esk
F - 4mm Hex Wrench x 1
I - Adhesive Foam/Magnet x 4
Pre-installed on Upper
Horizontal Beam (N)
a s s e m b l y i n s t r u c t i o n s
B - Top Glass x 1
-
K
Left Leg x 1
1
6001
6002
.
bDiusa
com
customerservice
A - Drawer Assembly x 1
D - Front Kick Panel x 1
G - 1/4-20 x 2 3/8" Screw x 7
H - 1/4-20 x 1/2" Screw x 16
M - Glides x 4
6 6
6005 5
6
6006
6 6007 7
6
@
.
bDiusa
com
-
L
Right Leg x 1
Advertisement
Related Manuals for BDI Sequel 6001
Summary of Contents for BDI Sequel 6001
- Page 1 Step 1 Unpack and identify the parts listed below. The assembly workspace should be a non- marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at customerservice@bdiusa.com. For all other concerns, please contact your BDI Retailer.
- Page 2 Step 1 Install Glides (M) to the bottom of Left Leg (K) and Right Leg (L). M x 4 assembly instructions bDiusa com customerservice bDiusa...
- Page 3 Step 2 Attach Left Leg (K) to Drawer Assembly (A) using Screw (H) and Hex Wrench (F). Step 3 Attach Right Leg (L) to Drawer Assembly (A) using Screw (H) and Hex Wrench (F). assembly instructions bDiusa com customerservice bDiusa...
- Page 4 Step 4 Attach Upper Horizontal Beam (N) to inside of Left and Right Leg using Screw (H) and Hex Wrench (F). assembly instructions bDiusa com customerservice bDiusa...
- Page 5 Step 5 2 Person Task Attach Lower Horizontal Beam (E) to inside of Left and Right Leg using Screw (H) and Hex Wrench (F). assembly instructions bDiusa com customerservice bDiusa...
- Page 6 2 Person Task Step 6 With the help of another person, gently lower Assembly onto Top Glass (B). Both parts will be placed upside down for the assembly process and fasten into place using Screw (G) and Hex Wrench (F) at all (7) fastener locations.
- Page 7 Step 7 (optional) Attach Magnets to AC power strip/surge protector Remove Adhesive Foam/Magnets (I) from the Upper Horizontal Beam (N). Peel film from side of the Adhesive Foam/Magnets (I) and attach to clean, dry back side of AC power strip (not included). Cleaning of power strip surface with rubbing alcohol will ensure best adhesive bond.
- Page 8 Step 11 Place Sequel Desk in desired location. Once all of the electrical wires are routed, install Kick Panel (D) as shown above. The rear side of panel has magnets that will hold the panel in place. Note: The Sequel Desk is designed to permit placement in front of an electrical outlet for easier wiring access.