Related Manuals for IBASE Technology MT800M-AIC
Summary of Contents for IBASE Technology MT800M-AIC
- Page 1 MT800M-AIC ® Gen. Intel Core™ i7/i5/i3 ® / Xeon E Motherboard with DC_IN 24V Input User’s Manual Version 1.0 (February 2021)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”). Disclaimer IBASE reserves the right to make changes and improvements to the products described in this document without prior notice.
- Page 3 0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) MT800M-AIC User’s Manual...
- Page 4 CAUTION Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions or recycle them at a local recycling facility or battery collection point. MT800M-AIC User’s Manual...
- Page 5 • Software in use (such as OS and application software, including the version numbers) If repair service is required, you can download the RMA form athttp://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and contact your distributor or sales representative. MT800M-AIC User’s Manual...
-
Page 6: Table Of Contents
Hardware Configuration ......11 Installations ..................12 2.1.1 Installing the Memory ............12 Setting the Jumpers ................13 Jumpers& Connectors on MT800M-AIC ..........14 Jumpers Quick Reference ..............15 2.4.1 AT/ATX Mode Setting (JP1) ..........15 2.4.2 Clear CMOS Setting (JP2)........... 16 2.4.3... - Page 7 Main Settings ..................37 Advanced Settings ................38 Chipset Settings .................48 SecuritySettings .................51 Boot Settings ..................52 Save & ExitSettings ................53 Appendix ..............54 I/O Port Address Map ................55 Interrupt Request Lines (IRQ) ............57 Watchdog Timer Configuration ............59 On-Board Connector Types ...............63 MT800M-AIC User’s Manual...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Specifications • Block Diagram • Board View • Board Dimensions... -
Page 10: Introduction
Introduction ® MT800M-AIC is a motherboard based on the Intel Generation Processor that features DC_IN 24V input two DDR memory sockets and supports up to 32 GB and high-performance graphics processing to create media-rich content and brilliant HD entertainment with DVI-D, VGA and DisplayPort display interface. -
Page 11: Packing List
General Information Packing List Your MT800M-AIC package should include the items listed below. If any of the items below is missing, contact the distributor or dealer from whom you purchased the product. • MT800M-AICMotherboard • Disk (with chipset drivers) •... -
Page 12: Specifications
Audio codec ALC662S-VD0-GR Power Supply DC_IN 24V H/W Monitor Watchdog Yes (256 segments, 0, 1, 2…255 sec / min) Timer BIOS AMI BIOS RAID RAID 0/1/5/10 RoHS Dimensions 200mm x 270mm Certification CE(EN55032:2012), FCC Class B, LVD MT800M-AIC User’s Manual... - Page 13 • Operating: 0~60 °C (32 ~ 140 °F) Temperature • Storage: -20 ~ 80 °C (-4 ~ 176°F) Relative 0 ~ 90 %, non-condensing at 60 °C Humidity All specifications are subject to change without prior notice. MT800M-AIC User’s Manual...
-
Page 14: Block Diagram
Block Diagram MT800M-AIC User’s Manual... -
Page 15: Board View
General Information Board View Top View Bottom View MT800M-AIC User’s Manual... - Page 16 Mic-In & Line out DVI-D Port LED for EtheNET port *Green for power LED USB 3.1 (Gen1) / USB 2.0 DP++ (left) & DP (MXM) LED for Power/HDD (right) /2x error warning COM1 / COM2 Ports Power Button MT800M-AIC User’s Manual...
-
Page 17: Dimensions
General Information Dimensions MT800M-AIC User’s Manual... - Page 18 This page is intentionally left blank. MT800M-AIC User’s Manual...
-
Page 19: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration This section provides information on jumper settings and connectors on the board in order to set up a workable system. The topics covered are: • Essential installations before you begin: CPU and the memory • Jumpers and connectors... -
Page 20: Installations
Gently push the module in an upright position until the ejector tabs of the memory slot close to hold the module in place when the module touches the bottom of the slot. To remove the module, press the ejector tabs outwards with your fintertips to eject the module. MT800M-AIC User’s Manual... -
Page 21: Setting The Jumpers
1 2 3 When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On. When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off. MT800M-AIC User’s Manual... -
Page 22: Jumpers& Connectors On Mt800M-Aic
Jumpers& Connectors on MT800M-AIC MT800M-AIC User’s Manual... -
Page 23: Jumpers Quick Reference
Hardware Configuration Jumpers Quick Reference Function Jumper Page AT/ATX Mode Setting Clear CMOS Setting Clear ME Setting Flash Descriptor Security Override (Factory use) 2.4.1 AT/ATX Mode Setting (JP1) Function Pin closed Illustration AT Mode ATX Mode(default) MT800M-AIC User’s Manual... -
Page 24: Clear Cmos Setting (Jp2)
2.4.2 Clear CMOS Setting (JP2) Function Pin closed Illustration Normal(default) Clear CMOS 2.4.3 Clear ME Setting (JP3) Function Pin closed Illustration Normal(default) Clear ME MT800M-AIC User’s Manual... -
Page 25: Flash Descriptor Security Override (Factory Use) Jp4
Hardware Configuration 2.4.4 Flash Descriptor Security Override (Factory use) JP4 Function Pin closed Illustration Disable Open Upgrade Mode Close MT800M-AIC User’s Manual... -
Page 26: Connectors Quick Reference
CN12 SPI Flash Tool Header (Factory use only) MXM Power Connector (19V) Gigabit LAN Header J15, J16, J17, J18 Digital I/O Connector SATAPWR1, SATA HDD Power Connectors SATAPWR2 SIM Card Socket CPU_FAN1 & Fan Power Connector SYS_Fan2 MT800M-AIC User’s Manual... -
Page 27: Port Debug Tool Connectors (J1)
2.5.2 X16 Slot, Not Standard but for IP-T803 use (PCIE1) 2.5.3 USB 3.1 Ports (CN3, CN4) Signal Name Signal Name P2_U2_D+ P1_SSRX- P2_U2_D- P1_SSRX+ Ground Ground P2_SSTX+ P1_SSTX- P2_SSTX- P1_SSTX+ Ground Ground P2_SSRX+ P1_U2_D- P2_SSRX- P1_U2_D+ P2_U2_D+ MT800M-AIC User’s Manual... -
Page 28: Front Panel Settings Connector (J2)
• Hard Disk Drive LED Connector (Pins 19 and 20) This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed. MT800M-AIC User’s Manual... -
Page 29: Com3, Com4, Com5, Com6 Ports (J10, J11, J9, J8)
J11, J9, J8) Signal Name Signal Name DCD, Data carrier detect DSR, Data set ready RXD, Receive data RTS, Request to send TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator Ground MT800M-AIC User’s Manual... -
Page 30: Com1& Com2 Rs-232/422/485 Ports (Cn12)
DCD, Data carrier detect DSR, Data set ready RXD, Receive data RTS, Request to send TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator Ground Signal Name RS-232 RS-422 RS-485 DATA- DATA+ Ground Ground Ground MT800M-AIC User’s Manual... -
Page 31: Spi Flash Tool Header (Factory Use Only) (J12)
Hardware Configuration 2.5.7 SPI Flash Tool Header (Factory use only) (J12) 2.5.8 MXM Power Connector (19V) - (J13) Signal Name Signal Name Ground Ground 2.5.9 DC_IN 24V Power Connector (J14) Signal Name Signal Name Ground Ground MT800M-AIC User’s Manual... -
Page 32: Gigabit Lan Header (J15, J16, J17, J18)
2.5.10 Gigabit LAN Header (J15, J16, J17, J18) Signal Name Signal Name LAN_XMDI0P LAN_XMDI0N LAN_XMDI1P LAN_XMDI1N LAN_XMDI2N LAN_XMDI2P LAN_XMDI3P LAN_XMDI3N 2.5.11 Digital I/O Connector (J20) Signal Name Signal Name Ground OUT3 OUT1 OUT2 OUT0 MT800M-AIC User’s Manual... -
Page 33: Sata Hdd Power Conn. (Satapwr1, Satapwr2)
Hardware Configuration 2.5.12 SATA HDD Power Connectors (SATAPWR1, SATAPWR2)* * (E-CALL 0110-071-040) Signal Name Signal Name Ground Ground +12V 2.5.13 SIM Card Socket (CN5) Signal Name Signal Name Ground RESET DATA CLOCK MT800M-AIC User’s Manual... -
Page 34: Fan Power Connector (Cpu_Fan1 & Sys_Fan1)
2.5.14 Fan Power Connector (CPU_FAN1 & SYS_Fan1) Signal Name Signal Name Ground Rotation detection +12V Control MT800M-AIC User’s Manual... -
Page 35: Chapter 3 Drivers Installation
Chapter 3 Drivers Installation This chapter introduces installation of the following drivers: • ® Intel Chipset Software Installation Utility • HD Graphics Driver • HD Audio Driver • LAN Driver • ® Intel Management Engine Drivers Installation... -
Page 36: Introduction
Follow the instructions below to complete the installation. Insert the disk enclosed in the package with the board. Click Intel on the left pane and then Intel(R) Coffeelake Chipset Drivers on the right pane. Click Intel(R) Chipset Software Installation Utility. MT800M-AIC User’s Manual... -
Page 37: Hd Graphics Driver Installation
The driver has been completely installed. Restart the computer for changes to take effect. HD Graphics Driver Installation Click Intel on the left pane and then Intel(R) Coffeelake Chipset Drivers on the right pane. Click Intel(R) HD Graphics Driver. MT800M-AIC User’s Manual... - Page 38 When the Welcome screen appears, click Next to continue. Accept the license agreement and click Next. On the Readme File Information screen, click Next until the installation starts. When Setup is Complete, restart the computer for changes totake effect. MT800M-AIC User’s Manual...
-
Page 39: Hd Audio Driver Installation
Drivers on the right pane. Click Realtek High Definition Audio Driver. On the Welcome screen of the InstallShield Wizard, click Next. Click Next until the installation starts. The driver has been completely installed. Restart the computer for changes to take effect. MT800M-AIC User’s Manual... -
Page 40: Lan Driver Installation
LAN Driver Installation Click Intel on the left pane and then Intel(R) Coffeelake Chipset Drivers on the right pane. Click Intel(R) PRO LAN Network Drivers. When the Welcome screen appears, click Next. MT800M-AIC User’s Manual... -
Page 41: Intel ® Management Engine Drivers Installation
The wizard is ready to begin installation. Click Install. As the installation is complete, click Finish. ® Intel Management Engine Drivers Installation Click Intel on the left pane and then Intel(R) Coffeelake Chipset Drivers on the right pane. MT800M-AIC User’s Manual... - Page 42 When the Welcome screen appears, click Next. Accept the license agreement, choose a destination folder and click Next until the installation starts. As the driver has been successfully installed, restart the computer for changes to take effect. MT800M-AIC User’s Manual...
-
Page 43: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Boot Settings •... -
Page 44: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. MT800M-AIC User’s Manual... -
Page 45: Main Settings
Sets the date. Use Tab to switch between the data elements. Default Ranges: System Date Year: 2005-2099 Months: 1-12 Days: depends on the month System Time Set the time. Use Tab to switch between the Time elements. MT800M-AIC User’s Manual... -
Page 46: Advanced Settings
User Select Monitor Output by Graphic Output Protocol Policy Protocol USB Configuration Displays USB configuration parameters. Network Stack Network Stack Settings Configuration Enables / Disables option ROM execution CSM Configuration settings, etc. NVMe Configuration NVMe Device Options Settings MT800M-AIC User’s Manual... - Page 47 When enabled, a VMM can utilize the Virtualization additional hardware capabilities provided by Technology Vanderpool Technology. Number of cores to enable in each processor Active Processor package. Cores Options: All, 1, 2, 3 Enables / Disables AES (Advanced Encryption Standard). MT800M-AIC User’s Manual...
- Page 48 BIOS Setting Description CPU – Power CPU – Power Management Control Options Management Control Allows more than two frequency ranges to be Intel SpeedStep supported Intel Speed Shift This can be Enabled or Disabled. Technology 4.4.3 PCH-FW Configuration MT800M-AIC User’s Manual...
- Page 49 (OS/S4 Sleep State). This option may be not effective with some OS. Selects an ACPI sleep state where the system will enter when the Suspend button is pressed. ACPI Sleep State Options: Suspend Disabled, S3 (Suspend to RAM) MT800M-AIC User’s Manual...
- Page 50 4.4.5 F81966 Super IO Configuration BIOS Setting Description Setsparameters of Serial Ports. Serial Port Enables /Disables the serial port and select an Configuration optimal setting for the Super IO device. MT800M-AIC User’s Manual...
- Page 51 PC health status. CPU Shutdown Options: Disabled / 70 °C / 75°C / 80°C / 85 Temperature °C / 90 °C / 95 °C 4.4.7 AMI Graphic Output Protocol Policy BIOS Setting Description MT800M-AIC User’s Manual...
- Page 52 Output Select Selects the display output interface MT800M-AIC User’s Manual...
- Page 53 Options: 1 sec / 5 sec / 10 sec / 20 sec Seconds of delaying execution of start unit command to USB mass storage device. Device reset time-out Options: 10 sec / 20 sec / 30 sec / 40 sec MT800M-AIC User’s Manual...
- Page 54 Options: Auto / Manual Mass storage device emulation type. ‘Auto’ enumerates devices according to their media Mass Storage format. Optical devices are emulated as Devices ‘CDROM’. Drives with no media will be emulated according to a drive type. MT800M-AIC User’s Manual...
- Page 55 Description CSM Support Enables / Disables CSM support. Controls the execution of UEFI and Legacy PXE OpROM. Network Options: Do not launch / Legacy 4.4.11 NVMe Configuration BIOS Setting Description NVMe Configuration NVMe controller and drive information. MT800M-AIC User’s Manual...
-
Page 56: Chipset Settings
BIOS Setting Description System Agent (SA) System Agent (SA) parameters Configuration PCH-IO PCH parameters Configuration 4.5.1 System Agent (SA) Configuration BIOS Setting Description Graphics Configures the graphics settings. Configuration VT-d Checks if VT-d function on MCH is supported. MT800M-AIC User’s Manual... - Page 57 16M / 20M / 24M / 28M / 32M/F7 / 36M / 40M / 44M / 48M / 52M / 56M / 60M DVMT Total Gfx Selects DVMT 5.0 total graphic memory size used by the internal graphcis device. Options: 256M / 128M / MAX MT800M-AIC User’s Manual...
- Page 58 4.5.2 PCH-IO Configuration BIOS Setting Description SATA and RST Configures SATA devices. Configuration PCH LAN Controller Enables / Disables the onboard NIC. Enables/ Disables the integrated LAN to wake Wake on LAN Enable up the system. MT800M-AIC User’s Manual...
-
Page 59: Securitysettings
System is in User mode. The mode change requires platform reset. Secure Boot mode options: Standard or Custom. Secure Boot Mode In Custom mode, Secure Boot Policy variables can be configured by a physically present user without full authenticatoin. MT800M-AIC User’s Manual... -
Page 60: Boot Settings
Timeout key.65535(0xFFFF) means indefinite waiting. Bootup NumLock Selects the keyboard NumLock state. State Quiet Boot Enables/Disables Quiet Boot option. Boot mode select Selects a Boot mode, Legacy / UEFI. Boot Option Priorities Sets the system boot order. MT800M-AIC User’s Manual... -
Page 61: Save & Exitsettings
Restores /Loads defaults values for all the Restore Defaults setup options. Save as User Saves the changes done so far as User Defaults Defaults. Restore User Restores the user defaults to all the setup Defaults options. MT800M-AIC User’s Manual... -
Page 62: Appendix
Appendix This section provides the mapping addresses of peripheral devices, the sample code of watchdog timer configuration, and types of on-board connectors. MT800M-AIC User’s Manual... -
Page 63: I/O Port Address Map
Programmable interrupt controller 0x00000038-0x00000039 Programmable interrupt controller 0x0000003C-0x0000003D Programmable interrupt controller 0x000000A0-0x000000A1 Programmable interrupt controller 0x000000A4-0x000000A5 Programmable interrupt controller 0x000000A8-0x000000A9 Programmable interrupt controller 0x000000AC-0x000000AD Programmable interrupt controller 0x000000B0-0x000000B1 Programmable interrupt controller 0x000000B4-0x000000B5 Programmable interrupt controller 0x000000B8-0x000000B9 Programmable interrupt controller MT800M-AIC User’s Manual... - Page 64 Intel(R) PCI Express Root Port #10 - A331 0x00002000-0x000020FE Motherboard resources 0x00006000-0x0000603F Intel(R) UHD Graphics 630 0x00000040-0x00000043 System timer 0x00000050-0x00000053 System timer 0x00000060-0x00000060 Standard PS/2 Keyboard 0x00000064-0x00000064 Standard PS/2 Keyboard 0x00004000-0x00004FFF Intel(R) PCI Express Root Port #12 - A333 0x0000EFA0-0x0000EFBF Intel(R) SMBus - A323 MT800M-AIC User’s Manual...
-
Page 65: Interrupt Request Lines (Irq)
IRQ 19 (COM7) IRQ 4294967266 Intel(R) Management Engine Interface IRQ 4294967292 Intel(R) UHD Graphics 630 IRQ 11 Intel(R) Thermal Subsystem - A379 IRQ 11 Intel(R) SMBus - A323 IRQ 0 System timer IRQ 1 Standard PS/2 Keyboard MT800M-AIC User’s Manual... - Page 66 Intel(R) I211 Gigabit Network Connection #3 IRQ 4294967270 Intel(R) I211 Gigabit Network Connection #3 IRQ 4294967269 Intel(R) I211 Gigabit Network Connection #3 IRQ 4294967268 Intel(R) I211 Gigabit Network Connection #3 IRQ 4294967267 Intel(R) I211 Gigabit Network Connection #3 MT800M-AIC User’s Manual...
-
Page 67: Watchdog Timer Configuration
#include<conio.h> #include<stdio.h> #include<stdlib.h> #include"F81966.H" //--------------------------------------------------------------------------- int main (int argc, char*argv[]); voidEnableWDT(int); voidDisableWDT(void); //--------------------------------------------------------------------------- intmain(intargc,char*argv[]) unsigned char bBuf; unsigned charbTime; char**endptr; charSIO; printf("Fintek81966watchdogprogram\n"); SIO =Init_F81966(); if (SIO ==0) printf("CannotdetectFintek81966,programabort.\n"); return(1); }//if (SIO ==0) if (argc !=2) printf("Parameterincorrect!!\n"); return(1); MT800M-AIC User’s Manual... - Page 68 |=0x01; Set_F81966_Reg(0xFA, bBuf); //enable WDTOoutput bBuf =Get_F81966_Reg(0xF5); bBuf |=0x20; Set_F81966_Reg(0xF5, bBuf); //startcounting //--------------------------------------------------------------------------- voidDisableWDT(void) unsigned charbBuf; Set_F81966_LD(0x07); //switch to logicdevice7 bBuf =Get_F81966_Reg(0xFA); bBuf&=~0x01; Set_F81966_Reg(0xFA, bBuf); //disable WDTOoutput bBuf =Get_F81966_Reg(0xF5); bBuf&=~0x20; bBuf |=0x40; Set_F81966_Reg(0xF5, bBuf); //disableWDT //--------------------------------------------------------------------------- //--------------------------------------------------------------------------- MT800M-AIC User’s Manual...
- Page 69 F81966_BASE =0x2E; result =F81966_BASE; ucDid =Get_F81966_Reg(0x20); if (ucDid==0x07) //Fintek81966 gotoInit_Finish; } F81966_BASE =0x00; result =F81966_BASE; Init_Finish: return(result); //--------------------------------------------------------------------------- void Unlock_F81966(void) outportb(F81966_INDEX_PORT, F81966_UNLOCK); outportb(F81966_INDEX_PORT,F81966_UNLOCK); //--------------------------------------------------------------------------- void Lock_F81966(void) outportb(F81966_INDEX_PORT,F81966_LOCK); //--------------------------------------------------------------------------- void Set_F81966_LD( unsigned charLD) Unlock_F81966(); outportb(F81966_INDEX_PORT,F81966_REG_LD); outportb(F81966_DATA_PORT, LD); Lock_F81966(); MT800M-AIC User’s Manual...
- Page 70 #define F81966_DATA_PORT (F81966_BASE+1) //--------------------------------------------------------------------------- #define F81966_REG_LD 0x07 //--------------------------------------------------------------------------- #define F81966_UNLOCK 0x87 #define F81966_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_F81966(void); void Set_F81966_LD( unsigned char); void Set_F81966_Reg( unsigned char, unsigned char); unsigned char Get_F81966_Reg( unsigned char); //--------------------------------------------------------------------------- #endif // F81966_H MT800M-AIC User’s Manual...
-
Page 71: On-Board Connector Types
52X-40-20GU52 19-pin Front Panel Dupont E-call Settings 2.54mm 2*5- 0126-01-203-200 Connector 24V Power Haoguo Connector 01-0018-02 4.2mm 2*4-pin CPU Fan Power Techbest Molex CPU_FAN1 Connector W2-03I104132S1WT(A)-L 47054-1000 System Fan Techbest W2- Molex SYS_Fan1 Power 03I104132S1WT(A)-L 47054-1000 Connector MT800M-AIC User’s Manual...
Need help?
Do you have a question about the MT800M-AIC and is the answer not in the manual?
Questions and answers