Table of Contents
Advertisement
SYSTEM MANAGER
SYSTEM MANAGER
7 SYSTEM MANAGER
7.1
Putting into service
9
The appliance must be maintained and adjusted at least
once a year by Technical Assistance Service or by profession-
ally qualified staff in compliance with all applicable Nation-
al and Local provisions.
9
Incorrect maintenance or adjustment may damage the ap-
pliance and cause damage to people or create a hazard.
9
The system manager is forbidden from opening and remov-
ing the appliance's casing. These activities must be carried
out only by Technical Assistance Service or by professionally
qualified personnel.
The thermal module Steel Pro Power
R
must be commis-
sioned by Technical Assistance Service
R
, after which step the
appliance may operate automatically.
However, the system manager may be required to restart the
appliance independently, without involving Technical Assistance
Service; for example after a long period of absence.
To do so, perform the following checks and operations:
− Check that the gas cock and heating water cock are open
− While the system is still cold, check that working pressure
in the central heating circuit is over 1 bar but below the
maximum limit specified for the boiler
− Adjust the room thermostats for the high and low tem-
perature zones to the required temperature (~20°C) or,
if the systems are equipped with timer thermostats or a
time programming unit, make sure it is on and adjusted
(~20°C)
− Switch the system's master switch to the ON position and
the thermal module's master switch to (I).
The appliance will go through the switch-on stage and, after
starting, it will continue to operate until set temperatures are
achieved.
The burner will then switch off and on automatically to main-
tain the set temperature without further operator action.
In the event of ignition or operation faults, the display will show
a numeric error code that will enable the user to interpret the
possible cause as detailed in Paragraph "Error List".
9
In the event of a permanent error, to reset starting condi-
tions press the "RESET" key and wait for the thermal module
to restart.
Repeat this operation 2-3 times at the most. If the problem per-
sists after that, call
's Technical Assistance Service.
R
System manager
108
SYSTEM MANAGER
7.2
Temporary or short-term shut-down
In the event of temporary or short-term shut-down (e.g. due to
holidays), proceed as follows:
− Press the MENU key and select with keys ▲ / ▼ "Time
schedule", confirm with key ●.
− Select with keys ▲ / ▼ "Holiday Schedule" and confirm
with key ●.
Clock Program
"
"
Program Group
"
"
Burn hours till service
"
"
Reset Service Reminder
"
"
Holiday Settings
"
"
− Select with keys ▲ / ▼ "Mode" and confirm with key ●.
Select "System" mode and confirm.
Holiday Settings
"
"
Mode
System
"
"
"
Holiday Setpoint
Comfort
"
"
"
Begin Date
Saturday
01-08-2015
"
"
"
"
End Date
Saturday
01-08-2015
"
"
"
"
− Select with keys ▲ / ▼ "Holiday Setpoint" and confirm
with key ●.
− Select "Antifreeze" holiday setpoint and confirm.
Holiday Settings
"
"
Mode
System
"
"
"
Holiday Setpoint
Anti Fr
"
"
"
Begin Date
Saturday
01-08-2015
"
"
"
"
End Date
Saturday
01-08-2015
"
"
"
"
7.3
Preparing for extended periods of disuse
The following operations shall be necessary if the thermal mod-
ule is not used for a long period of time:
− turn the main switch of the thermal modules and the
main system switch to "off"
− Close the fuel and water valves for the heating and do-
mestic hot water system.
9
Empty the thermal and sanitary system if there is a danger
of frost.
7.4
Cleaning
Use a cloth damped in soapy water to clean the boiler's external
casing.
To remove stubborn marks, use a cloth damped in a 50% mix
of water and denatured alcohol or a suitable cleaning product.
Carefully dry after cleaning.
0
Do not use abrasive cleaning pads or powder detergents.
0
Never clean the boiler without first disconnecting it from the
"
mains electricity supply by turning the mains power switch
and the control panel switch OFF .
"
9
The combustion chamber and flue pipes must be cleaned
periodically by the manufacturer's Technical Assistance Ser-
vice or by a qualified heating engineer.
7.5
Maintenance
Please remember that THE PERSON RESPONSIBLE FOR SYSTEM MAN-
AGEMENT MUST ENSURE THAT PROFESSIONALLY QUALIFIED HEATING
ENGINEERS UNDERTAKE PERIODIC MAINTENANCE AND COMBUSTION
EFFICIENCY MEASUREMENTS.
"
's Technical Assistance Service is qualified to satisfy these
"
R
legal requirements and can also provide useful information on
MAINTENANCE PROGRAMMES designed to guarantee:
− Greater safety
− Compliance with applicable legislation
− Freedom from the risk of fines in the event of spot checks.
Regular maintenance is essential for the safety, efficiency and
durability of the boiler.
Servicing is a legal requirement and must be performed at least
once a year by a professionally qualified heating engineer.
109
SYSTEM MANAGER
Advertisement
Table of Contents
