Commissioning And Maintenance; Initial Startup; Switching The Appliance On And Off; Date And Time Setting - Riello STEEL PRO POWER Installation, Technical Assistance Service And System Management Manual

COMMISSIONING AND MAINTENANCE

3 COMMISSIONING AND MAINTENANCE
3.1

Initial startup

− Switch the system's master switch to the ON position and
the thermal module's master switch to (I).
3.1.1

Switching the appliance on and off

After switching the appliance on, the display shall look as shown
in the figure below:
04:29
12.0 °C
" "
CH Setpoint 48.0 °C
" " " "
External temperature is shown on the display on the left. This
value is displayed only if the outdoor temperature sensor (ac-
cessory) is installed.
Main setpoint values are shown in the lower side of the display
while the time is shown on the top right side.
To turn the equipment off set the main switch "0/I" that is
placed on the back side to "0".
9
Never power off the appliance before switching the master
switch to the "0" position.
9
Never switch off the appliance with the master switch if a
request is active. Always make sure that the appliance is in
stand-by before switching the main switch.
3.1.2

Date and time setting

Press the MENU key and select "Settings" with the ▲ / ▼ keys
Menu
" "
Central Heating (CH)
" "
Information
" "
Settings
" "
System Test
" "
Confirm with the ● key and select "General settings" with the
▲ / ▼ keys
Settings
" "
General Settings
" "
Boiler Settings
" "
Confirm with the ● key and select "Date and Time " with the ▲
/ ▼ keys
General Settings
" "
Language
" "
Unit Type
" "
Date & Time
" "
Cascade mode
" "
Press the ● key, the display will be shown as follows:
Date & Time
" "
Date:
"Sunday" 10/25/2015
" "
Time: 03:02
" "
Time Zone Settings
" "
Display Settings
" "
Press the ● key to highlight the values.
Date & Time
" "
Date:
Sunday 10/25/2015
" " " "
Time: 03:02
" "
Time Zone Settings
" "
Display Settings
" "
Values can be changed with the ▲ / ▼ keys.
Confirm the value entered pressing the ● key and move to the
next value.
Date & Time
" "
Date:
Sunday 10/25/2015
" "
" "
Time: 03:02
" "
Time Zone Settings
" "
Display Settings
" "
To set the time, follow the same procedure.
By accessing the "Time Zone Setttings" menu, it is possible to set
the time zone parameter as shown in the figure below:
Time Zone Settings
" "
Time Zone Correction UTC +00.00
" "
Daylight Savings Time Disabled
" " " "
To change the way in which date and time are displayed, it is
possible to change the following characteristics by accessing the
"Display Settings" menu:
Display Settings
" "
Time Notation 24h
" " " "
Date Order DMY
" " " "
Day Of Month 2Digits
" " " "
Month 2Digits
" " " "
66
Display Settings
" "
Year 4Digits
" " " "
Date Separation Character -
" " " "
Day Of Week Short Text
" " " "
Seconds No
" " " "
3.1.3

Password access

To access the parameters, press the MENU key and select "Set-
tings" with the ▲ / ▼ keys.
Menu
" "
Domestic Hot Water (DHW)
" "
Information
" "
Settings
" "
System Test
" "
Confirm with the ● key and select "Boiler settings" with the ▲
/ ▼ keys
Settings
" "
General Settings
" "
Boiler Settings
" "
Press the ● key to confirm.
− The system will now ask you to enter a password (the
password is required for thermal module settings only):
Password
" "
0 * * *
COMMISSIONING AND MAINTENANCE
Enter one digit at a time using the ▲ / ▼ keys to increase/de-
crease the numeric value. When you have set the right value,
confirm by pressing the ● key.
The system provides for three types of access:
USER (password not required, e.g. password No. 0000)
INSTALLER (password No. 0300)
MANUFACTURER
9
After it is entered, the password is active during display and/
or parametrisation. If the display is inactive for a few min-
utes, it needs to be re-entered.
3.1.4

Setting the heating parameters

The parameter 1establishes the thermal module's various heat-
ing operation modes.
Mode 0
(Operation with room thermostat/heat demand and fixed heat-
ing setpoint)
In this mode, the thermal module operates with a fixed set-
point (controlled by the parameter3) based on whether the
room/heat demand thermostat's contact is closed or not.
The set-point value can be entered directly, without entering in
the parameter list, by accessing the "CH" menu in the following
way:
Press MENU and select "Central heating" using the ▲ / ▼ keys.
Press the ● key to confirm.
Menu
" "
Central Heating (CH)
" "
Domestic Hot Water (DHW)
" "
Information
" "
Settings
" "
After the selection, use the ► key to highlight the value and use
the ▲ / ▼ keys to change the selected value. Press the ● key to
confirm/save the new settings..
Central Heating (CH)
" "
CH Setpoint 61.5
" "
the set point can be set within a minimum and maximum val-
ue as indicated respectively on Par. 23 and 24 as shown in the
figure.
The outdoor temperature sensor (accessory) is not required and
if connected the outdoor temperature that is measured does
not influence the setpoint that has been set.
67
°C
" "