Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for RADWAG C32
Summary of Contents for RADWAG C32
- Page 2 NOVEMBER 2020...
- Page 3 500x400 C32.30.C2.K 500x400 C32.30.C2.M 500x400 C32.60.C2.R 500x400 C32.60.C2.K 500x400 C32.60.C2.M 500x400 C32.150.C2.R 500x400 C32.150.C2.K 500x400 C32.150.C2.M 500x400 C32.300.C2.R 500x400 C32.300.C2.K 500x400 C32.300.C2.M 500x400 C32.150.C3.K 700x500 C32.150.C3.M 700x500 C32.300.C3.K 700x500 C32.300.C3.M 700x500 For detailed technical specifications refer to RADWAG website www.radwag.com/pl/.
- Page 4 Protect the indicator against considerable temperature variation, solar and UV radiation, substances causing chemical reactions. The C32 scale must not be operated in hazardous areas endangered with explosion of gases, and in dusty environments. In case of damage, immediately unplug the device from the mains.
-
Page 5: Table Of Contents
7. INSTALLATION ..............................16 7.1. Unpacking and Installation ........................16 7.1.1. C32.D2 Series ..........................16 7.1.2. C32.xx.K, C32.xx.R, C32.F1.M Series ................... 17 7.1.3. C32.C2.M, C32.C3.M Series ......................17 7.2. Levelling..............................18 7.3. Connecting the Scale to the Mains ......................18 7.4. -
Page 6: Intended Use
USB type B, Ethernet, wireless communication, 2 proximity sensors, 4 I/O. Optionally the device can be equipped with an internal battery, this allows its operation in places where there is no access to the mains. C32 series scales team with receipt printers, barcode scanners, additional display, and PC accessories (mouse, keyboard, USB flash drive). -
Page 7: Cleaning Abs Components
In case of any sign of damage, it is necessary to disconnect the device form the mains immediately. The damaged component must be replaced or repaired by RADWAG service directly. In case of any problems with correct operation of the scale, contact the closest manufacturer's service point. -
Page 8: Recycling
6. MECHANICAL DESIGN The 1-load-cell C32 scale is intended to carry out fast and precise mass measurement of up to 300 kg loads. Its characteristic feature is a platform with one load cell only. The platform is equipped with a stainless steel weighing pan. -
Page 9: Dimensions
6.1. Dimensions C32.D2 series – overall dimensions C32.F1.R series – overall dimensions... - Page 10 C32.F1.M series – overall dimensions C32.F1.K series – overall dimensions C32.C2.R series – overall dimensions...
- Page 11 C32.C2.K series – overall dimensions C32.C2.M series – overall dimensions...
- Page 12 C32.C3.K series – overall dimensions C32.C3.M series – overall dimensions...
-
Page 13: Connectors Arrangement
RS232 - DSUB15/F connector (female), front: Pin8 - TxD2 Pin9 - 5VDC Pin10 - GND Pin13 - RxD2 6.4. Inputs / Outputs Standard C32 scale is equipped with 4 optoisolated inputs and 4 semiconductor outputs (solid-state relays). The signals are sent via DSUB15/F connector. -
Page 14: Technical Specifications
IN/OUT, RS232 - DSUB15/F connector (female), front: Pin1 – GNDWE Pin2 - OUT1 Pin3 - OUT2 Pin4 – COMM Pin6 - IN4 Pin7 - IN3 Pin11 - IN2 Pin12 - IN1 Pin14 - OUT4 Pin15 - OUT3 6.4.1. Technical Specifications Output parameters Output quantity Output type... -
Page 15: Operation Panel
6.5. Operation Panel Keys: Press to switch the device on / off. Press to enter the main menu. Press to log in. Press to cancel the message. Press to zero the scale. Press to tare the scale. Press to change the weighing unit. Press to confirm the message. -
Page 16: Installation
Programmable key assigned to an on-screen button. 7. INSTALLATION 7.1. Unpacking and Installation 7.1.1. C32.D2 Series A. Take the device out of the packaging. B. Place the device on a flat and even surface. Keep it away from any sources of heat. -
Page 17: C32.Xx.k, C32.Xx.r, C32.F1.M Series
7.1.2. C32.xx.K, C32.xx.R, C32.F1.M Series A. Take the device out of the packaging. B. Place the device on a flat and even surface. Keep it away from any sources of heat. C. Remove transport locks and install the weighing pan: 7.1.3. -
Page 18: Levelling
E. Lead the cable (in excess) into the post, next fix the support foot under the post: 7.2. Levelling It is necessary to level the scale, do it by turning its feet. Keep turning the feet until the air bubble takes central position. 7.3. -
Page 19: Battery Status
7.4. Battery Status Optional scale design features an internal battery. pictogram, displayed at the top of the screen, either signals battery status or informs that battery charging is in progress: pictogram displayed in a cyclic manner: battery charging. pictogram displayed continuously: battery charged within 75% - 100% range of permissible voltage, ... -
Page 20: Top Bar
Detailed instruction on how to configure the home screen is to be found in „PUE C32 Indicator Software Manual”. 8.1. Top Bar The top bar displays the following information: Working mode name and symbol. Weighing device name. Wireless communication on. -
Page 21: Pictograms
You can customize the workspace freely. 8.4. Pictograms The pictograms assigned to operation panel keys are to be found underneath the workspace. You can define on-screen pictograms individually for each working mode. 9. OPERATING THE MENU In order to navigate the program menu use the operation panel. 9.1. -
Page 22: Menu Keys
9.2. Menu Keys Press to enter the main menu. Press to go to the home screen. Press to go back, or to discard entering parameter modifications. Press to go back. Press to delete a character when editing numeric and text values. Press to change keyboard mode when editing numeric and text values. -
Page 23: Numerical Box
9.3.1. Numerical Box Where: Digit mode. To change keyboard working mode press key. Keyboard working mode options: - upper-case character mode, - lower-case character mode, - digit mode, - arrow keys operation, - bottom bar operation. Press to clear box content. Keys: Press to enter digit 1. -
Page 24: Text Box
Press to enter digit 8. Press to enter digit 9. Press to enter digit 0. Press to enter „.” sign (dot), long press. ( Press to delete one character. Press to exit, the edit box content remains unmodified. Press to confirm the modifications. Press to change keyboard working mode. - Page 25 Press to save the project to *.lb file on a USB flash drive. Press to read the project saved to *.lb file on a USB flash drive. Press to clear box content. Press to print the project using a printer connected to the scale. Press to view the list of variables that can be used in the project.
-
Page 26: Diacritical Sign Table
9.3.3. Diacritical Sign Table In order to activate the diacritical sign table while editing a text box, it is necessary to press and hold down key. Diacritical signs characteristic for a particular interface language are automatically added to the table when the given language gets selected. -
Page 27: Weighing
press key repeatedly, keep pressing the key until you see the home screen, press key, the home screen is displayed immediately. 10. WEIGHING Load the weighing pan. Read the result when stability marker is displayed. In order to assure long-term device operation, wherein correct measurements are provided, the following principles must be adhered to: Load the weighing pan steadily, avoid applying mechanical shocks. -
Page 28: Diagrams Of Connection Cables
11. DIAGRAMS OF CONNECTION CABLES Scale - computer cable (RS232) Scale - printer cable (ZEBRA) Scale - printer cable (EPSON) -
Page 29: Technical Specifications
I/O cable „Scale-Ethernet” cable is a standard network cable terminated with RJ45 connectors on both ends. 12. TECHNICAL SPECIFICATIONS For technical specifications of respective scales go to RADWAG website www.radwag.pl. 13. ERROR MESSAGES...