Advertisement
Hampton Corner Media
! CAUTION
The top shelf of this cart/stand is intended for use only with Plasma/LCD/DLP/HD televisions having a
•
maximum screen size of
size of
27
inches and weight of
All other support shelves should not be loaded more than 45 lbs.
•
DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the maximum sizes and
•
weights indicated may result in instability causing possible injury.
This unit contains a permanent sticker located either beneath media support shelf or inside drawer.
•
Do not allow children under 16 years to move cart.
•
! MISE EN GARDE
L'étagère supérieure de ce support ou chariot est destinée à recevoir une télévision à écran plasma ou
•
haute densité dont l'écran ne mesure pas plus de 114.3cm et qui ne pèse pas plus de
une télévision à tube cathodique don't l'écran ne mesure pas plus de
43.09
kg.
Les autres étagères ne doivent pas recevoir une charge de plus de 20.45 kg.
•
NE PAS DÉPASSER LA CHARGE RECOMMANDÉE. L'utilisation avec des articles qui dépassent la taille
•
et le poids recommandés peut rendre l'article instable et entraîner des blessures.
Cet article comprend un autocollant permanent, placé soit sous l'étagère supérieure, soit à l'intérieur du
•
tiroir.
Il faut interdire à tout enfant de moins de 16 ans de déplacer le chariot.
•
04-000077-2
PRE-ASSEMBLY:
For your safety and ease, assembly by two adults is recommended.
•
Read all instructions before beginning assembly.
•
Remove all parts and hardware from box and lay out on a carpeted or scratch-free work surface. The
•
shipping box provides and ideal work surface. Do not dispose of any contents until assembly is completed
to avoid accidentally discarding small parts or hardware.
PARTS INCLUDED:
A - Front Top panel - 1pc
B - Rear Top panel - 1pc
C - Bottom panel
- 1pc
D - Left side panel - 1pc
E - Right side panel - 1pc
F - Left partition panel - 1pc
G - Right partition panel – 1pc
H – Back panel – 1pc
I - Back support panel – 1pc
J – Left door – 1pc
K – Right door – 1pc
L – Center support leg – 1pc
M – Triangle shelf – 2pcs
N – Center shelf – 1pc
45
inches and weight of
100
95
lbs.
1/7
www.pbteen.com
lbs ; or Tube televisions having a maximum screen
68.58
cm et qui ne pèse pas plus de
45.4
kg. ou bien
Advertisement
Table of Contents
Related Manuals for PB TEEN Hampton Corner Media
Summary of Contents for PB TEEN Hampton Corner Media
- Page 1 Hampton Corner Media ! CAUTION The top shelf of this cart/stand is intended for use only with Plasma/LCD/DLP/HD televisions having a • maximum screen size of inches and weight of lbs ; or Tube televisions having a maximum screen size of inches and weight of lbs.
- Page 2 HARDWARE INCLUDED: O – Allen Key – 1 pc P – Long hex bolt – 4 pcs Q – Short hex bolt – 12 pcs 1/4” 1 3mm 1/4” × × × × 13mm R – Half moon washer – 4 pcs S –...
- Page 3 2. Attach the Left partition panel (F) and Right Partition panel (G) to Bottom panel (C) by aligning wooden dowels on partition panels with pre-drilled holes in the bottom panel, insert 4 Short hex bolts (Q) through pre-drilled holes in the Bottom panel into metal inserts in partitions as shown below, Loosely tighten the bolts with Allen Key (O).
- Page 4 4. Lay Top panels (A&B) upside down on a soft, scratch-free surface. Attach the Rear top panel (B) to Front Top panel (A) by aligning pre-drilled holes in hinges with pre-drilled holes at back of the front top panel. Insert a Phillips head screw (T) through each pre-drilled hole in the hinges into pre-drilled hole at the front top panel as shown below;...
- Page 5 6. Fix Back panel (H) to the corner media with 14pcs Phillips head screw (X) as shown below, use pre-drilled holes in back panel as guidance. tighten all screws with Philips Head screw driver. 7. Attach the Back support panel (I) to the right side of back panel by inserting 6pcs Phillips head screw (T) through pre-drilled holes in the hinge into pre-drilled holes in back panel as shown below , tighten screws with Phillip head screwdriver.
- Page 6 8. Attach Left door (J) and Right door (K) to the Left side panel (D) and Right side panel (E),align pre-drilled holes in hinges on doors with metal inserts on corresponding side panels, insert 2 Bolts (S) through pre- drilled holes in each hinge into the metal inserts on side panels as shown below, tighten the bolts with Phillip head screwdriver.
- Page 7 10. Adjust levers under feet and/or center support leg of the unit in or out to level the Media. CARE INSTRUCTIONS: Avoid direct sunlight and excessive temperatures. • Dust often using a clean, soft, dry and lint-free cloth. • Waxing is not recommended on lacquered finish. •...
Need help?
Do you have a question about the Hampton Corner Media and is the answer not in the manual?
Questions and answers