Page 1
LP0282 PAGE 1 OF 19 FITTING INSTRUCTIONS FOR LP0282 LICENCE PLATE BRACKET YAMAHA YZF R1 R1M 2020- This kit contains the items pictured and labelled over page. Some parts may be shown for clarity of instructions only. Do not proceed until you are sure all parts are present.
LP0282 PAGE 7 OF 19 FITTING INSTRUCTIONS • Remove the pillion seat using the key as shown in picture 1. • Remove the two bolts arrowed in picture 2 and remove the tool holder/cable bracket. • Unclip the two wiring holders arrowed in picture 3.
Page 8
PAGE 8 OF 19 LP0282 • Offer the assembly into position as original while feeding the wires through the under-tray as original and using the two shorter M6 button head bolts and washers (items 6 and 9) through the front holes (the front of the motorcycle) from underneath, use two of the Nyloc nuts with washers (items 5 and 6) to secure in position as shown in pictures 17 and 18.
Page 9
LP0282 PAGE 9 OF 19 MONTAGEANLEITUNG FÜR LP0282 KENNZEICHENHALTER YAMAHA YZF R1 R1M 2020- Alle Kit-Teile sind auf den nachfolgenden Seiten abgebildet und gekennzeichnet. Die abgebildeten Teile dienen lediglich zur Erklärung. Überprüfen Sie zuerst, dass alle Teile vorhanden sind. Lesen Sie die Montageanleitung komplett durch, bevor Sie anfangen.
Page 15
LP0282 PAGE 15 OF 19 MONTAGEANLEITUNG • Entfernen Sie den Soziussitz (der Schlüssel wird benötigt) wie in Abbildung 1 abgebildet. • Entfernen Sie die zwei Schrauben, die in Abbildung 2 gekennzeichnet sind und entfernen Sie den Werkzeughalter / Kabelhalter. •...
Page 16
PAGE 16 OF 19 LP0282 • Die Einheit an die original Position ansetzen und gleichzeitig die Kabel durch die untere Abdeckung schieben. Die zwei kürzeren M6 Inbusschrauben und Unterlegscheiben (Artikel 6 und 9) in die vorderen Öffnungen (vorne am Motorrad) einsetzen, von unten die zwei selbstsichernde Muttern mit Unterlegscheiben (Artikel 5 und 6) montieren, um sie in Position zu befestigen wie in den Abbildungen 17 und 18 abgebildet.
Page 17
LP0282 PAGE 17 OF 19 NOTICE DE MONTAGE POUR LP0282 SUPPORT DE PLAQUE YAMAHA YZF R1 R1M 2020- Ce kit contient les articles illustrés et étiquetés sur la page. Certaines parties peuvent être présentes uniquement pour la clarté des instructions.
LP0282 PAGE 23 OF 19 NOTICE DE MONTAGE • Retirez la selle passager à l'aide de la clé comme indiqué sur la photo 1. • Retirez les deux boulons fléchés sur la photo 2 et retirez le support d'outil/support de câble.
Page 24
PAGE 24 OF 19 LP0282 • Présentez l'assemblage en position d'origine tout en passant les fils à travers le plateau inférieur comme d'origine et en utilisant les deux boulons à tête ronde M6 plus courts et les rondelles (articles 6 et 9) à travers les trous avant (l'avant de la moto) par le dessous, utilisez deux des écrous Nyloc avec rondelles (articles 5 et 6) à...
Need help?
Do you have a question about the LP0282 and is the answer not in the manual?
Questions and answers