Aeotec Water Sensor 7 Pro Quick Start Manual
Hide thumbs
Also See for Water Sensor 7 Pro:
- User manual (14 pages) ,
- Manual (3 pages) ,
- User manual (9 pages)
Table of Contents
Advertisement
Quick Links
Water Sensor 7 Pro
SKU: AEOEZWA019
Quickstart
This is a secure Alarm Sensor for Europe. To run this device please insert fresh 1 * 1/2 AA batteries. Please
make sure the internal battery is fully charged. The DSK for the S2 inclusion can be found inside the sensors
packaging.
If your Z-Wave gateway supports SmartStart: scan the QR code on Water Sensor 7 Pro using the gateway's
app. Your sensor will join your Z-Wave network automatically.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or
may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage
resulting from failure to comply with the instructions in this manual or any other material. Use this equipment
only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or
batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for
use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming
every message (two-way communication) and every mains
powered node can act as a repeater for other nodes (meshed
network) in case the receiver is not in direct wireless range of
the transmitter.
This device and every other certified Z-Wave device can
be used together with any other certified Z-Wave device
regardless of brand and origin as long as both are suited for
the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this
device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of
security to maintain backward compatibility.
Advertisement
Table of Contents
Related Manuals for Aeotec Water Sensor 7 Pro
Summary of Contents for Aeotec Water Sensor 7 Pro
- Page 1 The DSK for the S2 inclusion can be found inside the sensors packaging. If your Z-Wave gateway supports SmartStart: scan the QR code on Water Sensor 7 Pro using the gateway’s app. Your sensor will join your Z-Wave network automatically.
- Page 2 The sensor is easily retrofittable. Thanks to its slim design the AEOTEC Water Sensor 7 Pro can be installed in any bathroom, behind a kitchen sink or in any other tight space. The sensor just has to be installed on the wall and the sensor probe must be put on the floor.
- Page 3 Exclusion 1. Open the housing. 2. Press the tamper on the side of the appliance three times quickly. Product Usage Once installed the sensor will report Leakage Detected and No Leakage status changes to a central Z-Wave controller using notification commands. Additionally, the sensor can directly control other devices using the association group 2.
- Page 4 devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
- Page 5 Switch after Water Leakage Stop Parameter 6: Command Sent to Devices of Association Group 2 This parameter defines which commands is sent to 2nd Association Group Size: 1 Byte, Default Value: 2 Setting Description On and Off Parameter 7: BASIC command value sent to 2nd Association Group on On event This is the BASIC command value sent in case of On event.
- Page 6 This parameter defines if the alarm cancellation event is reported. Size: 1 Byte, Default Value: 1 Setting Description Do not send Report Send Report Parameter 16: Minimum Temperature change to report This value defines the minimum change of temperature to cause an unsolicited report of temperature to the central controller using Lifeline.
- Page 7 Dimensions 28x95x35 mm Hardware Platform ZGM130S IP Class IP 20 Battery Type 1 * 1/2 AA Device Type Notification Sensor Generic Device Class Sensor Notification Specific Device Class Routing Sensor Notification Network Operation Reporting Sleeping Slave Firmware Version 01.00 Z-Wave Version 07.12 Z-Wave Product Id 0371.0002.0013...
- Page 8 • Exclusion — is the process of removing Z-Wave devices from the network. • Association — is a control relationship between a controlling device and a controlled device. • Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
Need help?
Do you have a question about the Water Sensor 7 Pro and is the answer not in the manual?
Questions and answers