Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BWT Aqua Flex T 200
Summary of Contents for BWT Aqua Flex T 200
- Page 1 Installation- and operating manual BW T A qua Flex T 200 -1000 Reservoir...
-
Page 2: Table Of Contents
General information....................... 3 Explanation of words ....................3 Functional description ....................4 BWT AQUA FLEX T 200, 600 &1000 ..................4 Option 1: Frequency controlled circulation pump and UV ............4 Option 2: Demi – Mix ......................5 Option 3: Solenoid valve for hot water dumping..............5 Option 4. -
Page 3: General Information
4. The installation manual have to be read thoroughly before connecting the plant. Correct installation of the plant will mean that there is 12 months of guarantee. 5. The guarantee will not be valid if the plant is not installed by an authorized BWT HOH service technician. -
Page 4: Functional Description
As an option, it is possible to install a UV Lamp on the BWT AQUA Flex 200-1000. The UV light will limit organic growth in the water; it means growths of microorganisms, sponges and bacteria. -
Page 5: Option 2: Demi - Mix
Option 4. Extra high level switch It is possible that situations where the water level of BWT AQUA Flex t can be to high can occur. The extra high alarm will send a signal to the RO unit. The RO unit will stop producing Permeat when the water level is at a critical level. - Page 6 1. There must be a decline to the floor drain to ensure the water flows towards the drain. 2. The water should be able to run unobstructed from the plant to the floor drain.
-
Page 7: Water Connections
Power consumption [kW] 0.85 kW The electric connection to the BWT AQUA Flex BWT AQUA Flex reservoir must be as follows: All internal connections in the BWT AQUA Flex, the pump, recirculation system and UV is connected from the manufacturer. It is therefore only the power that have to be connected to a supply... -
Page 8: Start-Up - Bwt Aqua Flex 200-1000
Wait for the BWT AQUA Flex reservoir tank to be completely filled. 2: Check that the tank level automatically stops the plant when the BWT AQUA Flex reservoir is full. NOTE: Do not touch the level sensor. -
Page 9: Trouble Shooting
Trouble shooting LED lights overview The LED light will normally light up in the colour of the component they represent. Restart Alarm Look if the transport starts TP-pump: Nothing works – and stops. permanent situation. Water Level low(No Alarm) Look is the water level is low. -
Page 10: Alarm Overview
Check if too many consumers are connected on the BWT AQUA Flex reservoir and switch some off. Let the BWT AQUA Flex reservoir become completely filled up. Check if the level sensor float is stuck in top of the Error 1: BWT AQUA Flex reservoir. - Page 11 The motor of the transport pump is Check the wiring diagram of the BWT AQUA Flex running in the wrong direction. reservoir and make a correct connection. If the piping connection is too small there ...
-
Page 12: Technical Data
Technical data: BWT AQUA Flex T 1000 with internal pump Reservoir volume 1.000 Transport pump 0,85 kW, 4,5A bar/ Pump capacity (m3/h) Reservoir, diameter (A) Ø510 Ø1.000 Ø760 Unit, height (B) 1.365 1.670 1.670 Unit, width (C) Inlet pipe connection, height ~1.020... -
Page 13: Installation
Installation It is possible to change the installed time for start and stop. Furthermore, the delay in the start can be planned. Application of the DIP Switch: 1. Raw water pressure measurement(time from start of the high pressure pump to measurement of the pressure) 2. -
Page 14: Start Op Control
NO, the problem does not concerns the plant or the installation The plant - we mean only the part of the whole installation which was delivered by BWT (i.e only the plant). The installation - we mean the piping etc. leading to the plant. -
Page 15: Service And Maintenance
Service and maintenance... -
Page 16: Operation Manual
Operation manual... -
Page 17: P&I Diagram Without Options
P&I diagram without options... -
Page 18: P&I Diagram With Options
P&I diagram with options... -
Page 19: Layout Drawing Without Options
Layout drawing without Options. -
Page 20: Electrical Connections
Electrical connections... -
Page 22: Spare Parts List
200 l reservoir 401526055 401526056 600 l reservoir 401526057 1,000 l reservoir Internal transport pump 454100070 (BWT AQUA Flex 200, 600, 1000) External transport pump CME 3-5 454100900 External transport pump CM 3-5 454100950 External transport pump CM 3-5 454100960 Main switch(On/OFF) 750001580 Hydrophore 2.0 liter... - Page 23 14A Filter house 321401000 Sterile filter 321409005 1 years Quick fittings 12 mm 454091012 BWT Conductivity Censor K = 0,3 452536500 BWT Conductivity Censor K =1,0 452536501 Pressure hose 3/4” 1000 mm 656513020 10 mm plastic hose 454001010 3 years...
-
Page 24: Spare Parts Drawing Without Options
Spare parts drawing without options... -
Page 25: Spare Parts Drawing With Options
Spare parts drawing with options... -
Page 26: Declaration Of Conformity
+45 43 600 500 - fax: +45 43 600 900 bwt@bwt.dk - www.bwt.dk Here with declares that: BWT AQUA Flex T 200, 600, 1000 and 2000 is in conformity with the provisions of the Machinery Directive (Directive 2006/42/EC) is in conformity with the provisions of the following other EC directives... -
Page 27: 10 Disposal
In Denmark and several other countries, BWT itself assumes responsibility for the return and conformant disposal of its electronic and electrical products. These products may not be placed with household waste or brought to collection centres run by local public disposal operations –... - Page 28 Fax: +33 1 4922 45 45 E-Mail: office@bwt.at E-Mail: bwt@bwt.de E-Mail: info@cillichemie.com E-Mail: bwt@bwt.fr BWT Belgium NM. BWE Česká Republika s.r.o. BWT Polska Sp. z o.o. BWT Hungária Kft. Leuvensesteenweg 633 Lipovo 196 -Cestlice ul. Polczyhska 116 Keleti út. 7. B-1930 Zaventem CZ-251 01 Říčany...
Need help?
Do you have a question about the Aqua Flex T 200 and is the answer not in the manual?
Questions and answers