Table of Contents
Advertisement
carriage is fully OPEN.
A:
Light ON/OFF key
B:
ON/OFF key
Pressing this button with the carriage closed
The light switches on and off only when the
This starts the extraction carriage upward
will cause the carriage to open and then the
carriage is fully OPEN.
movement and when it is fully open, it sets the
light will switch on .
Pressing this button with the carriage closed
second extraction speed.
The button also serves to switch off the light
will cause the carriage to open and then the
With the carriage open: it switches off the mo-
if it is on.
light will switch on .
tor and if on, the light; then it retracts the ex-
O P E R A T I N G T H E D O W N D R A F T E X T R A C T O R
The button also serves to switch off the light
traction carriage.
if it is on.
B:
ON/OFF key
C:
(-) Key
This starts the extraction carriage upward
B:
movement and when it is fully open, it sets the
ON/OFF key
This reduces the speed of the extractor motor
O F F K E Y
second extraction speed.
from the 4th speed until the motor switch-
This serves to close the extraction panel either completely from any position that is more than
This starts the extraction carriage upward
With the carriage open: it switches off the mo-
es off, without closing the pull-out car-
180mm from the hob. When the extraction panel is being closed, it will remain in operation until it
movement and when it is fully open, it sets the
tor and if on, the light; then it retracts the ex-
riage.
reaches 180mm above the hob. Below this height, the extraction function will switch
second extraction speed.
traction carriage.
With the carriage open: it switches off the mo-
off automatically.
tor and if on, the light; then it retracts the ex-
D:
Indicators
C:
(-) Key
traction carriage.
( - ) K E Y
Reduces the speed of the extraction motor. This button only works when the height of the
• This signals the speed setting, by only
This reduces the speed of the extractor motor
the relevant LED switching on.(see
extraction panel is more than 180mm from the hob.
from the 4th speed until the motor switch-
C:
(-) Key
'Timing' on pg 11 for further information)
es off, without closing the pull-out car-
• This signals that all filters have been satu-
I N D I C ATO R S
This reduces the speed of the extractor motor
riage.
rated by all LEDs switching on.
Indicates the chosen level of extraction speed.
from the 4th speed until the motor switch-
es off, without closing the pull-out car-
E:
(+) Key
riage.
D:
Indicators
( + ) K E Y
This serves to bring the extraction panel up to a maximum height of 300mm and to automatically
• This signals the speed setting, by only
This increases the speed of the extractor mo-
set the first extraction speed when the panel reaches a height of 180mm. Pressing the button
the relevant LED switching on.(see
D:
Indicators
tor, from 1st to 4th speed, without moving the
again after 180mm is reached, will increase the extraction speed.
'Timing' on pg 11 for further information)
extractor panel.
• This signals the speed setting, by only
• This signals that all filters have been satu-
the relevant LED switching on.(see
rated by all LEDs switching on.
F:
Timer
'Timing' on pg 11 for further information)
T I M E R
10
• This signals that all filters have been satu-
10 minutes after pressing this button and setting the function, it serves to stop the extractor motor
E:
(+) Key
10 min after setting, it serves to stop the ex-
rated by all LEDs switching on.
and close the carriage.
tractor motor, close the carriage and switch
This increases the speed of the extractor mo-
the lights off, if they are on. The set function is
E:
(+) Key
tor, from 1st to 4th speed, without moving the
signalled by the flashing LEDs "D" for the set
extractor panel.
speed. The timer can be cancelled by press-
This increases the speed of the extractor mo-
ing the key again.
tor, from 1st to 4th speed, without moving the
extractor panel.
10
Other functions:
10
Automatic turn off:
After 4 hours of continuous working from
the last function selection, the appliance
turns off and closes automatically.
Grease filters saturation:
After 30 hours of working, the speed indica-
tors "D" will all flash simultaneously, signaling
16
Instruction manual DD606BK
the grease filters saturation.
After 30 hours of working, the speed indica-
ing the key again.
Other functions:
tors "D" will all flash simultaneously, signaling
the grease filters saturation.
To reset this alarm, hold down the "TIMER"
Other functions:
button for at least 3 seconds, while the car-
riage is open.
Automatic turn off:
After 4 hours of continuous working from
Calibration:
the last function selection, the appliance
The cooker hood carries out its self
turns off and closes automatically.
calibration every 3 complete cycles of its
extractable unit.
Grease filters saturation:
By pushing the "TIMER" key 6 times consec-
After 30 hours of working, the speed indica-
utively (MAX break between one push and the
tors "D" will all flash simultaneously, signaling
other is 3 sec.) all the leds will flash and the
the grease filters saturation.
calibration will be reset.
To reset this alarm, hold down the "TIMER"
After the next 3 cycles the downdraft will carry
button for at least 3 seconds, while the car-
out its self calibration.
riage is open.
Stand-by:
Calibration:
When the extractable unit is closed and the
The cooker hood carries out its self
light is switched off, the control panel,
calibration every 3 complete cycles of its
after 6 seconds, activates the stand-by
extractable unit.
function, reducing the brightness of the leds.
By pushing the "TIMER" key 6 times consec-
This function can be stopped by pressing ON/
utively (MAX break between one push and the
OFF or LIGHT key.
other is 3 sec.) all the leds will flash and the
calibration will be reset.
After the next 3 cycles the downdraft will carry
out its self calibration.
Stand-by:
When the extractable unit is closed and the
light is switched off, the control panel,
after 6 seconds, activates the stand-by
function, reducing the brightness of the leds.
This function can be stopped by pressing ON/
OFF or LIGHT key.
Please keep this instruction manual for future reference
Automatic turn off:
After 4 hours of continuous working from
the last function selection, the appliance
turns off and closes automatically.
Grease filters saturation:
After 30 hours of working, the speed indica
tors "D" will all flash simultaneously, signalin
the grease filters saturation.
To reset this alarm, hold down the "TIMER
button for at least 3 seconds, while the ca
riage is open.
Calibration:
The cooker hood carries out its self
calibration every 3 complete cycles of its
extractable unit.
By pushing the "TIMER" key 6 times consec
utively (MAX break between one push and th
other is 3 sec.) all the leds will flash and th
calibration will be reset.
After the next 3 cycles the downdraft will car
out its self calibration.
Stand-by:
When the extractable unit is closed and th
light is switched off, the control panel,
after 6 seconds, activates the stand-by
function, reducing the brightness of the leds
This function can be stopped by pressing ON
OFF or LIGHT key.
Advertisement
Table of Contents
