Lutron Electronics Vive PowPak Installation

PowPak | Installation
Control Module with DALI
Part of the Vive Family
RMNS-DAL4-SZ
220 – 240 V~ 50 / 60 Hz 50 mA
RMNS-DAL32-SZ
DALI Control: 18 V-
Guaranteed Supply Current:
8 mA on 4-driver controller (RMNS-DAL4-SZ)
•
• 64 mA on 32-driver controller (RMNS-DAL32-SZ)
Maximum Supply Current: 250 mA
Important Notes: Please read before installing.
For installation by a qualified electrician in accordance with all local and
national electrical codes.
• Use copper conductors only.
• Check to see that the device type and rating is suitable for the application.
• DO NOT install if product has any visible damage.
• If moisture or condensation is evident, allow the product to dry completely
before installation.
• Operate between 0 °C and 40 °C ambient.
• 0% to 90% humidity, non-condensing.
• For indoor use only.
PowPak
Control Module
Install in center of room
to maximize RF coverage.
Radio Powr
Savr Occupancy
Sensor
PowPak
9 m
Control
maximum Module
Pico
Remote
Control
All Wireless Transmitters must be installed within 9 m
of the PowPak Control Module with DALI.
Default Functionality
Occupancy Sensors
Occupied: All lights 100%.
Unoccupied: All lights off.
Daylight Sensor
All lights dim in response to daylight.
Link Cal.
Test
Wireless Controls
On All lights 100%
Favorite All lights 50%
Off All lights off
Lutron Electronics Co., Inc. | 7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Required Components
For each system, ensure that you have:
One PowPak Control Module At least one Wireless Transmitter
041588 041797
Rev. A Rev. A
02/2021
02/2021
Top LED
Raise
+
Toggle
Lower
Bottom
LED
Radio Powr Savr Occupancy/Vacancy Sensor
(10 maximum)
Start Here
Mount, Wire, and Install DALI Devices and
1
Lighting Fixtures
Consult third-party device installation guide
WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit
breaker before installing the unit.
A
Connect mains wiring (hot, neutral) to each fixture.
B Connect DALI control to each fixture.
Neutral
Line/Hot
+ DA+
– DA-
To additional DALI fixtures
Programming with a Vive Hub
3
A B
Use an iOS or Android compatible device.
Vive X
Troubleshooting
Ballasts cannot be controlled locally from PowPak Control Module
with DALI.
Lights do not dim as expected.
Lights do not respond to Wireless Transmitter(s).
Lights are unstable at low-end or flash/flicker at turn-on or turn-off. • Adjust the low-end trim.
Wireless Transmitter(s) cannot be associated to PowPak Control
Module with DALI.
Pico Remote Control
(10 maximum)
Install PowPak Control Module
2
with DALI
Suggested Installation Location: Center of room to
ensure proper RF coverage of area.
A
Install the 1/2 in NPT to 20 mm conduit adapter (provided) onto the
PowPak Control Module.
B
The PowPak Control Module can be installed on a fixture / troffer,
junction box, or marshalling box using the conduit nut (provided) or
with mounting screws (not provided). Please consult local and national
electric codes for proper installation.
NEU
C Once installed, energize the PowPak Control Module.
Sample LED
HOT
driver shown
D
Use the Toggle " u " , Raise "▲" and Lower " " buttons to verify
control wiring.
DA+
DA–
Wire Gauge
1.5 mm 2 (14 AWG)
0.75 mm (18 AWG)
2
0.50 mm 2 (20 AWG)
C
Download the Lutron Vive app. Open the app and follow the instructions.
• Ensure that the breaker(s) to the PowPak Control Module are energized.
• Ensure that the DALI control lines are wired to the lighting fixture(s).
Reset to factory defaults.
• Ensure that DALI control lines are wired properly.
• Ensure that the breaker(s) to the PowPak Control Module and drivers/ballasts are energized.
• Ensure that Wireless Transmitters are associated to the PowPak Control Module.
• Ensure that Wireless Transmitter(s) are within 9 m of the PowPak Control Module.
Reset to factory defaults.
• Ensure that Wireless Transmitter(s) are within 9 m of the PowPak Control Module.
• The maximum number of Wireless Transmitters have been associated to the PowPak Control Module. To remove a previously set up Wireless Transmitter, tap a
Wireless Transmitter button three times; on the third tap hold for three seconds and then tap three more times.
Customer Assistance www.lutron.com/support
At least one DALI LED Driver or Fluorescent Ballast
Consult third-party DALI fixtures installation guide for fixture-specific wiring. This device can
be installed on a fixture / troffer, junction box, or marshalling box using the conduit nut or with
mounting screws. The device must NOT be mounted inside a fixture / troffer or other metallic
enclosure. Improper installation can result in degraded wireless communication, intermittent or
sustained communication failures, and will not be covered under warranty. For mounting and
wiring best practices see Lutron Application Note #620 (P/N 048620).
+
Link Cal.
Test
Radio Powr Savr Daylight Sensor 8 mA / 64 mA (based on model) guaranteed for the control lines.
(1 maximum) May be pre-installed in light fixture.
Line / Hot (Red)
Neutral (Black)
Wiring a Lever
Operated Connector
When wiring lever-
operated connectors
(4 supplied) use
appropriate gauge solid or
stranded copper wire.
Total DALI-compliant
1
3
Bus Wire Length
10 mm
2
300 m
150 m
100 m
Note: For further information on set up, programming, and troubleshooting with a Vive
system, please refer to the installation instructions included with the Vive hub or visit
www.lutron.com/vive-europe
Note: For programming the PowPak Control Module with DALI without a Vive hub see
vive.lutron.com X
.
reverse side
DA+ (Violet)
DALI to Fixtures
DA- (Violet/White)
Conduit Nut
1/2 in NPT to
20 mm Conduit
Adapter
www.lutron.com / vive