Nibe ELK 213 Installer Manual
Immersion heater
Hide thumbs
Also See for ELK 213:
- Installer manual (28 pages) ,
- Installation and maintenance instructions manual (26 pages) ,
- Installer manual (24 pages)
Subscribe to Our Youtube Channel
Related Manuals for Nibe ELK 213
Summary of Contents for Nibe ELK 213
- Page 1 IHB EN 2036-8 INSTALLER MANUAL - ELECTRIC HEATER 031403 Immersion heater NIBE ELK 213...
-
Page 3: Table Of Contents
Item register Contents Assembly Contact information Component positions Front panel 3 Pipe connections General Pressure drop diagram ELK 213 System diagram Installation alternative 4 Electrical connection Electrical connection versions F1345 F1345 2.0 / F1355 F1345 SMO S40 SMO 20 and SMO 40... -
Page 4: Important Information
Children shall not play with the appliance. Cleaning and user The serial number can be found on the type plate on the side of ELK 213. maintenance shall not be made by children without supervision. Caution... -
Page 5: General
ELK 213 is equipped with a time relay. Time delay is recommended when the connected power exceeds 6 kW. The thermostats for the immersion heater and isolator switch are operated by knobs on the control panel. -
Page 6: Component Positions
Connection supply line, R50 Connection return line, R50 XL10 Drain connection R20 * Counter flanges, R50. Accessory needed. See section "Accumulator tank (SP 300)" on page for more information. Designations according to standard EN 81346-2. Chapter 2 | General NIBE ELK 213... -
Page 7: Front Panel
FQ10-S2 Temperature limiter Reset a tripped temperature limiter by pressing the button. Only do this once the cause of the fault has been rectified, see section "Troubleshooting" on page 16. NIBE ELK 213 Chapter 2 | General... -
Page 8: Pipe Connections
The safety valve must be "exercised" regularly, at least four times a year. NOTE The pipe work must be flushed before the electric heater is connected, so that any con- taminants do not damage the component parts. Chapter 3 | Pipe connections NIBE ELK 213... -
Page 9: System Diagram
(Part no. 022 077). must be planned according to applicable standards. In the event of large hot water demands, ELK 213, in- stalled on double-jacket accumulator tank type, can be used to heat the domestic hot water. This is also a good SYMBOL KEY solution for aggressive or hard water. -
Page 10: Electrical Connection
F1345 2.0 / F1355 NOTE All electrical connections must be carried out Terminal blocks X1 and X8 in ELK 213 connect to the by an authorised electrician. terminal blocks X5, X7 and X8 on the input board AA101 Electrical installation and wiring must be carried in the heat pump as illustrated. -
Page 11: F1345
F1345 SMO 20 and SMO 40 Terminal blocks X1 and X8 in ELK 213 connect to the For connecting ELK 213 to SMO 20 and SMO 40. terminal blocks X2-X4 in the heat pump as illustrated. Terminal blocks X1 and X8 in ELK 213 connect to termin- al blocks X1 and AA7-X2 in SMO 20 and SMO 40 as il- lustrated. -
Page 12: Power Supply
7/9 kW in three steps VVM 500 For connecting ELK 213 via accessory board AXC 40. Terminal blocks X1 and X8 in ELK 213 connect to termin- al block AA5-X9 in AXC 40 as illustrated. 11/13 kW in three steps... -
Page 13: Time Relay
Time relay Connection of the circulation pump ELK 213 is equipped with a time relay (KF1), which blocks part of the immersion heater via contactor (QA2) so that a maximum of 6 kW is connected during the first (GP10) two hours after ELK 213 has been disconnected. -
Page 14: Program Settings
5 Program settings Program setting the ELK 213 can be performed via the Menu 7.5.3 - Forced control start guide or directly in the menu system in your com- Forced control of the various components in the main patible heat pump/indoor module. - Page 15 • EB1-AA5-K3: Activating additional step 3. • EB1-AA5-K4: Activating the circulation pump (GP10). Caution Linear stepping of ELK 213 is recommended. F1145, F1155, F1245, F1255, VVM 225, VVM 310, VVM 320, VVM 325 and VVM 500 Information about menu settings for the products above is in the manuals for AXC 40, DEH 310 and DEH 500.
-
Page 16: Disturbances In Comfort Troubleshooting
• The pressure is to low in the expansion vessel. • The load monitor or some external control unit may have blocked the power output. POOR CIRCULATION • Circulation pump, if fitted is stationary. Chapter 6 | Disturbances in comfort NIBE ELK 213... -
Page 17: Technical Data
7 Technical data Dimensions All dimensions in mm. 280 mm 200 mm * Counter flanges, R50. Accessory is required. NIBE ELK 213 Chapter 7 | Technical data... -
Page 18: Technical Specifications
Sound power level, indoors For combination heaters Declared load profile for water heating Water heating energy efficiency ƞ Daily energy consumption Daily fuel consumption elec fuel Annual energy consumption Annual fuel consumption Chapter 7 | Technical data NIBE ELK 213... -
Page 19: Electrical Circuit Diagram
Electrical circuit diagram NIBE ELK 213 Chapter 7 | Technical data... -
Page 20: Item Register
Technical documentation, 18 Installation alternative Accumulator tank, 9 Boiler with internal water heater, 9 Marking, 4 Pipe connections Symbol key, 9 Safety information Marking, 4 Symbols, 4 Serial number, 4 Symbol key, 9 Symbols, 4 Item register NIBE ELK 213... -
Page 23: Contact Information
Tel: +46 (0)433-27 3000 kuzmin@evan.ru info@nibe.se nibe-evan.ru nibe.se SWITZERLAND NIBE Wärmetechnik c/o ait Schweiz Industriepark, CH-6246 Altishofen Tel. +41 (0)58 252 21 00 info@nibe.ch nibe.ch For countries not mentioned in this list, contact NIBE Sweden or check nibe.eu for more information. - Page 24 WS version: a819 (working edition) Publish date: 2020-09-10 11:51 This manual is a publication from NIBE Energy Systems. All product illustrations, facts and data are based on the available information at the time of the publication’s approval. NIBE Energy Systems makes reservations for any factual or printing errors in this manual.
Need help?
Do you have a question about the ELK 213 and is the answer not in the manual?
Questions and answers