Table of Contents
Advertisement
Quick Links
BT8707
PREMIUM FLOOR-TO-WALL
SINGLE SCREEN TWIN COLUMN
UC STAND
INSTALLATION GUIDE
SPECIFICATIONS
• Recommended for screens up to: 100" (254cm)
• Max load: 100kg (220lbs)
• Suitable for displays with fixings up to 972 x 800mm
• Stand dimensions: H.1945 x W.1128 x D.162mm
• Integrated cable management
www.btechavmounts.com
Advertisement
Table of Contents
Related Manuals for B-Tech BT8707
Summary of Contents for B-Tech BT8707
- Page 1 BT8707 PREMIUM FLOOR-TO-WALL SINGLE SCREEN TWIN COLUMN UC STAND INSTALLATION GUIDE SPECIFICATIONS • Recommended for screens up to: 100" (254cm) • Max load: 100kg (220lbs) • Suitable for displays with fixings up to 972 x 800mm • Stand dimensions: H.1945 x W.1128 x D.162mm •...
-
Page 2: Installation Safety Instructions
Please check carefully to make sure there are no missing or defective parts - defective parts must never be used. B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire. - Page 4 BT8707 PARTS LIST PLEASE KEEP THIS FOR FUTURE REFERENCE NOT REQUIRED...
-
Page 5: Mounting Rail
ITEM PART DESCRIPTION 1.9M COLUMN END CAP COLUMN REAR COVER M6 x 12mm HEX SCREW M6 x 12mm GRUB SCREW (OPTIONAL) SQUARE NUT (OPTIONAL) COVER STRIP 3AF HEX KEY 4AF HEX KEY WALL PLATE BASE PLATE M6 x 12mm SCREW M8 x 50mm COACH SCREW M8 T1.5mm METAL WASHER N°.10 x 50mm WALL PLUG... - Page 6 Installation Instructions ATTACH MOUNTING BRACKETS TO COLUMNS i. Insert 4 x item C2 into item C1 and attach item C3. Screw two full turns to leave item C3 at the end of item C2. M6 x 40mm RECTANGLE CSK HEX SCREW ii.
- Page 7 ATTACH WALL PLATE TO COLUMNS Fix item B1 to the top of item A1 using item B3. M6 x 12mm HEX SCREW FIX FLOOR PLATES TO THE FLOOR TOP VIEW Fix item B2 to floor (fixings not included). 60mm Note: Fixing points are 60mm away from the wall. The floor plates should be set 600mm apart.
- Page 8 MARK WALL FIXING HOLES Using the guide pins, place item A1 onto items B2. Mark the 4 fixing holes from item B1 onto the wall. GUIDE PINS...
- Page 9 DRILL HOLES AND INSERT WALL PLUGS Remove item A1 and drill marked holes. Insert 4 x item B6 (Not required for stud/wood walls). 10mm Masonary Drill Bit MASONARY WALL...
- Page 10 HOOK RAILS ONTO MOUNTING BRACKETS i. Insert 4 x item C4 into item D1 (2 in the top channel, 2 in the bottom channel) on each side of the rails. M8 SLIDING M8 x 12mm ii. Screw 2 x item C5 into item C4 in the top channel - allow at least a 6mm gap HEX SCREW INSERT so the rail can be hooked on to item C1.
- Page 11 FIX COLUMN TO WALL Place item A1 onto item B2 and fix item B1 to the wall using items B4 & B5. M8 x 50mm WASHER COACH SCREW...
- Page 12 ATTACH INTERFACE ARMS TO SCREEN Fix items E1 to the rear of the screen using items E3 - E16. Note: Ensure the arms are facing the correct way round and the same holes are used on both arms. E3-E11 SCREEN Use spacers (items E13-E16) for screens with recessed fixings.
-
Page 13: Height Adjustment
LOCK SCREEN TO RAIL Tighten the safety screws on the bottom of item E1 securing the screen to item D1. Optional: Note: If necessary, adjust the height adjustment HEIGHT ADJUSTMENT screws on top of item E1 to level the screen. SCREW SAFETY SCREW... -
Page 14: Front View
PLEASE KEEP THIS FOR FUTURE REFERENCE FRONT VIEW Max 972mm 180mm 8.4mm 10.4mm 60.8mm 24mm BOTTOM VIEW 51mm 6.5mm 66mm 150mm THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT. -
Page 15: Rear View
REAR VIEW SIDE VIEW 50mm 50mm 162mm 50mm 79.5mm 15mm 8.5mm 20.5mm 60.8mm TOP VIEW 1005mm 90mm 51mm THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT. - Page 16 ©2020 B-Tech AV Mounts. All rights reserved. B-Tech AV Mounts is a division of B-Tech International Design and Manufacturing Ltd. B-Tech AV Mounts and the B-Tech logo are registered trade marks. All other brands and product names are trademarks of their respective owners.