Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Victron energy MPPT Control display
Summary of Contents for Victron energy MPPT Control display
- Page 1 ENGLISH MPPT Control display manual Rev 00 04/2021...
-
Page 2: Table Of Contents
MPPT Control display manual Table of Contents 1. Introduction ........................... 1 2. Mounting ..........................3 3. Installation ..........................5 4. Operation ..........................7 4.1. Status menu ........................8 4.2. History menu ......................... 8 4.3. Settings menu ......................10 5. Troubleshooting and Support ....................12 5.1. -
Page 3: Introduction
Power cable VE.Direct cable A VE.Direct cable is needed to connect the display to the solar charger. This cable is not included with the MPPT Control display and needs to be purchased separately. VE.Direct cables vary in lengths from 0.3 up to 10 meter and are available with straight or right angle connectors. For more information see the VE.Direct cable product... - Page 4 Wall mounting enclosure The housing of the MPPT Control display is tailored towards being flush mounted through a panel. In case flush mounting is not possible a dedicated wall mount enclosure can be used. This enclosure allows for easy wall mounting of the display.
-
Page 5: Mounting
MPPT Control display manual 2. Mounting Drill a hole in a mounting substrate as indicated in below figure. Mounting recess width and depth requirements Mount the display: Use option A if the mounting substrate is accessible from both sides Use option B if the mounting substrate is accessible from the front. - Page 6 MPPT Control display manual Mounting option B Page 4 Mounting...
-
Page 7: Installation
It is not possible to extend the VE.Direct cable, the maximum length can not exceed 10 meter. Power VE.Direct The rear of the MPPT Control display showing the power connection and the VE.Direct connection VE.Direct cable Connect the display to the solar charger via a VE.Direct cable... - Page 8 MPPT Control display manual VE.Direct cable To battery Fuse Connect the display to an old model solar charger and the battery Page 6 Installation...
-
Page 9: Operation
MPPT Control display manual 4. Operation The LCD screen displays the following information: • A number reading. • The unit of the reading: V, A, W, kWh, h or ! • The type of reading: load, battery, PV, min, max or charge stage. -
Page 10: Status Menu
MPPT Control display manual 4.1. Status menu This menu shows the live solar charger readings. The MPPT Control display always starts up in this menu. Press the up and down button cycle through all menu items. These menu items will be displayed in order of appearance as indicated in below table:... - Page 11 MPPT Control display manual History menu navigation chart All available history menu items are listed in below table, in the order they appear when scrolling through the items. Scrolling text Description TOTAL YIELD The cumulative PV yield since the last history reset.
-
Page 12: Settings Menu
Do not change settings unless you know what they are and what the effect of changing these setting can be. Incorrect settings may cause system problems including damage to batteries. When in doubt, seek advice from and experienced Victron Energy installer, dealer or distributor. To navigate the settings menu: •... - Page 13 MPPT Control display manual Some settings might be missing from the settings menu. The MPPT Control display only allows to change the most common settings. More advance settings, like TX and RX port settings, are not accessible via the MPPT Control display. To configure...
-
Page 14: Troubleshooting And Support
MPPT Control display manual 5. Troubleshooting and Support Consult this chapter in case of unexpected behaviour or if you suspect a product fault. The correct troubleshooting and support process is to first consult the common issues as described in this chapter. -
Page 15: Warranty
Victron Energy to make such repairs. Non-compliance with the instructions in this manual will render the warranty void. Victron Energy is not liable for any consequential damages arising from the use of this product. The maximum liability of Victron Energy under this limited warranty shall not exceed the actual purchase price of the product. -
Page 16: Specifications
52mm (2.0") Body depth 31mm (1.2") Power cable length 1.5m Weight Suitability Suitable for the entire Victron Energy BlueSolar MPPT and the SmartSolar MPPT solar charger range, with the exception of the (since long) discontinued BlueSolar MPPT 70/15. Page 14 Specifications...