DAB E.sybox Instruction For Installation And Maintenance page 60

GB
ENGLISH
INDEX
Key
Warnings
Responsibility
1. General
1.1 Description of the Integrated Inverter
1.2 Integrated expansion vessel
1.3 Integrated electropump
1.4 Technical characteristics
2. Installation
2.1 Vertical Configuration
2.1.1 Hydraulic connections
2.1.2 Loading operation – Installation above head and below head
2.2 Horizontal configuration
2.2.1 Hydraulic connections
2.2.2 Orientation of the interface panel
2.2.3 Loading operation – Installation above head and below head
3. Commissioning
3.1 Electrical connections
3.2 Configuration of the integrated inverter
3.3 Priming
4. Protection systems
4.1 Description of blockages
4.1.1 "BL" AAnti Dry-Run (Protection against dry running)
4.1.2 Anti-Cycling (Protection against continuous cycles without utility request)
4.1.3 Anti-Freeze (Protection against freezing of water in the system)
4.1.4 "BP1" Blockage due to fault of the internal pressure sensor
4.1.5 "BP2" Blockage due to reading error on the remote pressure sensor
4.1.6 PB" Blockage due to line voltage outside specifications
4.1.7 "SC" Blockage due to short circuit between the motor phases
4.2 Manual reset of error conditions
4.3 Self-reset of error conditions
5. Inverter electronic control and user interface
5.1 Operation with control unit
5.1.1 Functions made available by control units
5.1.2 Electrical connections of utility inputs and outputs
5.1.3 Safety mode operation
5.1.4 Connection to more than one control unit
5.1.5 Control unit function setup
5.1.6 Association and disassociation of e.sybox and control unit
60
6. The keypad and the display
6.1 Direct access with a combination of keys
63
6.2 Access by name with a drop-down menu
63 6.3 Structure of the menu pages
64 6.4 Blocking parameter setting by Password
6.5 Enabling and disabling the motor
64
7. Meaning of the individual parameters
65
7.1 User Menu
65
7.1.1 Status
66
7.1.2 RS: Rotation speed display
67
7.1.3 VP: Pressure display
68 7.1.4 VF: Flow display
68 7.1.5 PO: Absorbed power display
7.1.6 C1: Phase current display
69
70 7.1.7 Operating hours and number of starts
70 7.1.8 PI: Power histogram
7.1.9 Multi-pump system
70
71 7.1.10 Output flow meter
72 7.1.11 VE: Version display
7.1.12 FF: Fault log display
72
7.2 Monitor Menu
72
7.2.1 CT: Display contrast
73
7.2.2 BK: Display brightness
73
7.2.3 TK: Backlight switch-on time
7.2.4 LA: Language
74
7.2.5 TE: Dissipator temperature display
74
74 7.3 Setpoint Menu
7.3.1 SP: Setting the setpoint pressure
75
75 7.3.2 Setting the auxiliary pressures
7.3.2.1 P1: Setting the auxiliary setpoint 1
75
7.3.2.2 P2: Setting the auxiliary setpoint 2
75
75 7.3.2.3 P3: Setting the auxiliary setpoint 3
7.3.2.4 P4: Setting the auxiliary setpoint 4
75
7.4 Manual Menu
75
76 7.4.1 Status
7.4.2 RI: Speed setting
76 7.4.3 VP: Pressure display
7.4.4 VF: Flow display
76
7.4.5 PO: Absorbed power display
77
77 7.4.6 C1: Phase current display
7.4.7 RS: Rotation speed display
77
7.4.8 TE: Dissipator temperature display
78
78 7.5 Installer Menu
7.5.1 RP: Setting the pressure fall to restart
78
79
80
83
84
85
85
85
85
85
86
86
86
86
86
86
86
86
86
87
87
87
87
87
87
87
87
87
87
88
88
88
88
88
88
89
89
89
89
89
89
89
89
89
89