Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ametek Level Mate II
Summary of Contents for Ametek Level Mate II
-
Page 1: Rear Connections, Figure
LEVEL MATE LEVEL MEASUREMENT AND CONTROL SYSTEM INSTRUCTIONS FOR INSTALLATION, OPERATION, MAINTENANCE, SERVICE AND PARTS U.S. GAUGE, PMT PRODUCTS U. S. GAUGE, PMT PRODUCTS 820 PENNSYLVANIA BLVD., FEASTERVILLE, PA 19053 AK796441 REV F, NOV 14, 2002... -
Page 3: Table Of Contents
WARRANTY POLICY CONTENTS Page Ametek [“Seller”] warrants these products for a period of two years from the date of shipment that all products manufactured by the seller are free from defects of material and workmanship when used INTRODUCTION within the service, range, and purpose for which they were manufactured. Seller will, at its option, re-... -
Page 4: Introduction
INTRODUCTION PARTS and ACCESSORIES The Level Mate II Level Measurement System consists of an AMETEK Model DMC Digital Meter Controller used with an AMETEK Model 575 Submersible Transmitter to provide digital K223000 Seal plug for K554168 strain relief indication of liquid level. -
Page 5: Specifications
TROUBLE SHOOTING SPECIFICATIONS Check all wiring at terminal block at rear of meter for correct connections, bro- LEVEL MATE II 575 TRANSMITTER ken wires, loose or corroded connections or short circuits. FUNCTIONAL SPECIFICATIONS Range Limits: Reference Model Code Check for proper power voltage and wiring locations. -
Page 6: Model Dmc Digital Meter/Controller
Press the key to scroll until 4-20 appears on the display; press the key to save this. LEVEL MATE II DMC DIGITAL METER/CONTROLLER The display will show rnG. Press the key once to step to the StLO prompt; press the ENVIRONMENTAL key. -
Page 7: Ordering Information
THE STANDARD LEVEL MATE LIQUID LEVEL MEASUREMENT SYSTEM CONSISTS OF: A 316 STAINLESS STEEL, SNUBNOSED, AMETEK MODEL 550 SUBMERSIBLE TRAN S- alarm LED’s blinking will advise the monitor mode. To return to normal operation press any key: however it will... -
Page 8: Installation
UNPACKING AND INSPECTION ble future removal of the transmitter. Automatic Calibration (ACAL) The Level Mate II is calibrated with a specific Additional support can be provided when the trans- Submersible Transmitter. mitter is being used under circumstances of excess This function allows you to calibrate the unit to an applied signal. You may calibrate to a low signal (zero) and then stress, such as, when submerged in agitated water at a later time calibrate to the high signal (span). -
Page 9: Display
Use 0.047 microfarad 500V ceramic disc dary strikes of sufficient magnitude. AMETEK in series with a 10 ohm, ½ watt resistor. The two front panel keys may be defined by the user to perform one of several different functions while in the nor-... -
Page 10: Rs-232 Printer Output
RS-232 PRINTER OUTPUT KEYBOARD OPERATION and SETUP With the optional RS-232 printer output you can select three modes transmission. Entering the Setup menu. Continuous printing. 2. Single printout, key operated. 3. Continuous printout, key operated. Simultaneously press both the the key. Also selectable is the baud-rate, print rate and line terminator. - Page 11 TABLE VI - LEVEL MATE II INPUT TYPE & DISPLAY SCALING VIII LEVEL INPUT TYPE INCHES OF COUNT FEET OF COUNT METERS COUNT MATE II TRANSMITTER 4-20 mA WATER WATER OF WATER LMT100 575SB0006RLS(50) rdLO 00.0 0.00 .000 rdHI 166.4 13.86...
-
Page 12: Calibration
For details see page 22. Select rdHI, set 22.34 METHOD (3) IR REMOTE SETUP Then set the display resolution as follows. Alternately the Level Mate II can be pro- grammed (setup configured) via the optional Under CAL select SPEC LED pen. - Page 13 FIGURE 3 – MODEL 575 TRANSMITTER WITH CABLE SUPPORT CAUTION: The waterproof cable should Caution: The cable grommet is spe- not be kinked or nicked, which would cially installed by factory -trained per- also allow water to seep into the cable sonnel to assure watertightness.
Need help?
Do you have a question about the Level Mate II and is the answer not in the manual?
Questions and answers