Applications; Emergency Stop; Cleaning; Maintenace - IMER MIX 60 PLUS Instruction Manual

11. APPLICATIONS

11.1. ADHESIVES FOR CERAMIC TILES, FLOORING AND
WALL CLADDING
Pour in the quantity of water as required for the relative product,
considering that the maximum mixer capacity 100 lbs of adhesive.
Start the machine and during operation, pour the powder directly over
the plastic cover to obtain a smooth mixture.
- Warning: when mixing large quantities, pour the product
into the tank gradually.
11.1. PAINT
Pour in the required amount of paint and water.
- The use of acid, solvents, and other aggressive chemical
products is strictly prohibited.
11.1. CEMENT
Mix 60 can also mix mortar, cement, or lime provided that a fine
particle size is used.
- Warning: Avoid excessive stiffening of the mixture due to
the addition of too much cement, lime or other water absorbing
products.

12. EMERGENCY STOP

- In an emergency, press the green pushbutton and unplug
the mixer.
- The electric motor is protected from thermal overload; if
the motor overheats the mixer is shut down automatically. Allow
the motor to cool before resuming operation.

13. CLEANING

After each work shift and before prolonged periods of disuse, clean
the tank interior and exterior thoroughly.
- Always unplug the mixer from the mains before cleaning
(also when using brushes, cloths or scrapers etc.).
- Never operate the mixer during cleaning operations.
- When using water jets for cleaning, never direct the water at the
mixer drive unit.
14. MAINTENANCE
- Warning: Always switch off the mixer and unplug from the
power supply before carrying out maintenance.
- Repairs to the electrical installation must be carried out exclusively
by qualified personnel. Replacement parts must be original IMER
spare parts and must not be modified in any way.
The IMER MIX 60 PLUS is designed for minimum maintenance
requirements. However, we recommend changing the reduction unit
oil after 3000 hours continuous duty with SAE 40 oil.
Check that the socket/plug contacts are clean. If oxidised, clean
immediately.
- Used oil is considered a special waste product and must
be disposed of in accordance with the law.
- Always ensure that signs and warning notices on the
machine are clearly legible.
For any problem, see your dealer or call IMER U.S.A. @
800.275.5463.
IMER U.S.A. Inc.
MIX 60 PLUS

15. TROUBLE-SHOOTING

PROBLEM
The motor does not
start when switched
on
The motor does not
stop when the safety
grid is lifted
Motor starts with
difficulty
Should the problem
persist
16. SILICA DUST WARNING
Grinding/cutting/drilling of masonry, concrete, metal and other materials
with silica in their composition my give off dut or mists cintainig crystalli-
ne silica. Silica is a basic component of sand, quartz, brick clay, granite
and numerous other minerals and rocks. Repeated and/or substantial
inhalation of airborne crystalline silica can cause serious or fatal respira-
tory diseases, including silicosis. In addition, California and some other
authorities have listed respirable crystallinesilica as a substance known
to cause cancer. Whwn cutting such materials, always follow respiratory
precautions.
Use appropriate NIOSH-approved respiratory protection where dust
hazard may occur. Paper masks or surgical masks without a NIOSH
approval number are not recommended because they do little to protect
the worker. For more information about respirator programs, including
what respirators have received NIOSH approval as safe and effective,
please visit the NIOSH website at:
http://www.cdc.gov/niosh/topics/respirators
Observe OSHA regulations for respirator use (29 C:F.R. § 1910.134).
Visit http://www.osha.gov for more information.
California proposition 65 message
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contain chemicals know (to the State of Ca-
lifornia) to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
-Lead, from lead-based paints
-Crystalline silica, from bricks and cement and other masonry products
-Arsenic and chromium, from chemically treated lumber
For further information , consult the following sources:
http://www.osha.gov/dsg/topics/silicacrystalline/index.html
http://www.cdc.gov/niosh/docs/96-112/
http://oehha.ca.gov/prop65/law/P65law72003.html
http://www.dir.ca.gov/Title8/sub4.html
http://www.P65warnings.ca.gov
Your risk from these exposures varies depending on how often you do
this typer of work. To reduce your exposure to these chemicals, work in
a well-ventilated area, and work with approved safety equipment, such
as dust masks that are specially designed to filter out microscopic par-
ticles. Where use of a dust extraction device is possible, it should be
used. To achieve a high level oof dust collection, use an industrial HEPA
vacuum cleaner. Observe OSHA 29 CFR part 1926.57 and 1926.103.
6
CAUSE REMEDY
No power on power cable Check power cables
Plug not inserted correctly Ensure correct connection
in socket
Faulty power cable to Change power cable
electrical panel
Loose wire in electrical Reconnect wire
panel
Loose wire in motor Reconnect wire
terminal board
Faulty main switch Replace switch
Residual current circuit Reset switch. If it does not
breaker tripped reset, refer to a qualified
electrician to check the
electrical system to ensure
complete safety.
Faulty limit switch Replace limit switch
Mixture is too stiff Reduce mixture quantity or
dilute and try again.
Contact IMER Technical Service @ 800.275.5463 or
your IMER Dealer