Aeroflex SmartStep 8310 Operation & Installation Manual
  1. Manuals
  2. Brands
  3. Aeroflex Manuals
  4. Control Unit
  5. SmartStep 8310
  6. Operation & installation manual
Aeroflex SmartStep 8310 Operation & Installation Manual

Aeroflex SmartStep 8310 Operation & Installation Manual

Programmable attenuator
Hide thumbs
Table of Contents

Advertisement

Quick Links

Model 8310-XX-X-XN
Operation & Installation Manual
SmartStep
Aeroflex / Weinschel
Manual Rev. G (4-18-11)
Model 8310
®
Programmable Attenuator
Units w/Ethernet
This documentation may not be reproduced in any form, for any
purpose unless authorized in writing by Aeroflex / Weinschel, Inc.
© Aeroflex / Weinschel, Inc.
Frederick, Maryland
2008-2011
IM-493
IM-493
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SmartStep 8310 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Aeroflex SmartStep 8310

Summary of Contents for Aeroflex SmartStep 8310

  • Page 1 ® SmartStep Programmable Attenuator Units w/Ethernet This documentation may not be reproduced in any form, for any purpose unless authorized in writing by Aeroflex / Weinschel, Inc. © Aeroflex / Weinschel, Inc. Frederick, Maryland 2008-2011 Aeroflex / Weinschel Manual Rev. G (4-18-11)
  • Page 2 SAFETY SUMMARY SAFETY SUMMARY DEFINITIONS. • To minimize shock hazard, the instrument chassis must be connected to an electrical ground. Using The following definitions apply to WARNINGS, the supplied three-conductor power cable ensures CAUTIONS, and NOTES found throughout this manual. that the instrument can be firmly connected to the ac power source and electrical ground at a grounded power outlet.
  • Page 3 SAFETY SUMMARY NOTE CAUTION DO NOT return any instrument or component to Weinschel Corporation without receiving prior • All procedures and/or steps identified as factory authorization. must be followed exactly as written and according to industry accepted ESDS device handling procedures. Failure to comply WILL SAFETY SYMBOLS.

  • Page 4: Table Of Contents

    5-1.3.8 EXAMPLE SETUP USING THE SERIAL PORT ..............18-22 5-2. SERIAL OPERATION ............................22-23 5-2.1. RS-232 OPERATION ............................ 23 5-3. STATUS REPORTING ............................24-25 5-4. GENERAL SYNTAX STRUCTURE ..........................25 5-4.1. SYNTAX OF QUERIES ........................... 25 5-4.2. SYNTAX OF COMMANDS ........................25-26 Aeroflex / Weinschel...
  • Page 5 MODEL 8310-36-3-EN, ATTENUATOR UNIT ASSEMBLY REPLACEABLE PARTS LIST (P/N 193-7036-13) ....45 MODEL 8310-38-FN / -RN ATTENUATOR UNIT ASSEMBLY REPLACEABLE PARTS LIST (P/N 193-7038-9) ....45 MODEL 8310-38-2-FN / -RN ATTENUATOR UNIT ASSEMBLY REPLACEABLE PARTS LIST (P/N 193-7038-10) ..46 Aeroflex / Weinschel...
  • Page 6 MODEL 8310-352-4-TN, ATTENUATOR UNIT ASSEMBLY REPLACEABLE PARTS LIST (P/N 193-7403-8 ....57 ASSY, BASE UNIT W/ETHERNET (+15V) PARTS LIST (P/N 193-8034-3) ................ 58 ASSY, BASE UNIT W/ETHERNET (+5V) PARTS LIST (P/N 193-8034-4) ................59 8. CONTACTING AEROFLEX / WEINSCHEL......................60 AEROFLEX / WEINSCHEL WARRANTY ......................60 10. ASSEMBLY/WIRING DIAGRAMS MODEL 8310-1-X-XN ASSEMBLY DRAWING ................

  • Page 7: General Information

    8310-XXX-XN Series are single channel configurations where RF signal is routed through either the front or rear mounted Ports A & B connector (Ports A-A if the RF is routed front to rear) to a single or multiple Aeroflex / Weinschel programmable attenuators thus creating CH1 (Channel 1).

  • Page 8: Unpacking And Inspection

    Under U.S. shipping regulations, damage claims must be collected by the consignee; DO NOT return the equipment to Aeroflex / Weinschel until a claim for damages has been established. 1-6. RESHIPMENT: Use the best packaging materials available to protect the unit during storage or reshipment.

  • Page 9: Related Manuals

    Following these simple safety precautions will ensure safe operation and service of the Attenuator Unit. 1-12. POWER REQUIREMENTS: Aeroflex / Weinschel supplies a detachable power cable (P/N 068-21) to connect a 115 to 230 Vac power source with a frequency between 50 to 60 H to the Attenuator Unit.

  • Page 10: Specifications

    RF Characteristics NOTES: 1. RS-232 can be used with standard PC serial port for short and medium distances (up to approximately 50 ft). 2. Refer to Individual data sheet (Appendix C) for detailed specifications on internal programmable attenuators. Aeroflex / Weinschel...
  • Page 11 1.4 max 3206T-1 Rear 193-7038-14 8310-38-3-T-EN 63/1 dc-2 5.25 dB max 1.4 max 3206T-1 Front to Rear 193-7038-15 8310-38-4-T-EN 63/1 dc-3 5.25 dB max 1.4 max 3206T-1E Front to Rear 193-7038-16 Table 1, Continued on next page Aeroflex / Weinschel...
  • Page 12 1.6 max 4228T-103 Front 193-7138-6 8310-138-2-RN 103/1 0.8-3.0 6.0 dB max 1.6 max 4228T-103 Rear 193-7138-6 8310-138-3-TN 103/1 0.8-3.0 6.0 dB max 1.6 max 4228T-103 Front-Rear 193-7138-7 8310-138-4-TN 103/1 0.8-3.0 6.0 dB max 1.6 max 4228T-103 Front-Rear 193-7138-8 Aeroflex / Weinschel...

  • Page 13: Installation

    (Figure 1). The Fuse Drawer Assembly contains the line voltage fuse (Weinschel P/N 052-1-1.5). The Model 8310-XXX-XN uses a T 1.5A, 250 Vac fuse which is 5 x 20 mm in size. Refer to paragraph 6-4 for replacement of the fuse. Aeroflex / Weinschel...

  • Page 14: 3-3.2. Channel Port Connectors

    These connectors provide a input and output port where various types of RF signals can be applied to the devices internally mounted in the Model 8311-XX-X-XN (Connector location specified by customer when ordering). Some special configurations could contain Aeroflex / Weinschel’s Model 1568 SMA Panel Adapters or other types of crowns (see accessories for other types).

  • Page 15: Front Panel Controls & Indicators

    IEEE-488.2 local lockout or execution of the LOCKOUT command. ADDR: This key displays the current IEEE-488.2 address. The address may be changed from the front-panel, however, the initial setting at power on is derived from the rear-panel address switch. Aeroflex / Weinschel...

  • Page 16: Remote Operation

    Serial Mode: This position allows the RS232 port to be directly connected to the serial port of the 8210A, effectively bypassing the XPort’s ability to control the unit via the Ethernet port. In this mode, the serial port settings are controlled via the internal DIP switch of the 8210A. Aeroflex / Weinschel...

  • Page 17: 5-1.2 Serial Port Setup

    View Readme.txt located in the Lantronix Xport CD files Rev2 folder. c. Select the desired DeviceInstaller and run the associated setup program within the folder. d. Respond to the installation wizard prompts. (When prompted to select an installation type, select Typical.) Aeroflex / Weinschel...

  • Page 18: 5-1.3.2 Serial Port Login

    Select 0 (Server Configuration) and follow the prompts until you get to IP address. Enter the new IP address, subnet mask, and gateway (if applicable). g. Select 9 to save and exit Setup Mode. The unit performs a power reset. Aeroflex / Weinschel...

  • Page 19: 5-1.3.3 Arp And Telnet

    If another device is using the selected IP address, the unit selects another address from the AutoIP range and reboots. After reboot, the unit sends out another ARP request to see if the selected address is in use, and so Aeroflex / Weinschel...

  • Page 20: 5-1.3.7 Device Server Setup

    The easiest way to enter Setup mode is to hold down the 'x' key, and power up the unit. d. Response should be:: MAC address 00204AC530DB Software version V6.6.0.2 (080926) XPTEXE Press Enter for Setup Mode Aeroflex / Weinschel...
  • Page 21 Monitor Mode @ bootup: enabled RS485 tx enable: active low HTTP Port Number: 80 SMTP Port Number: 25 MTU Size: 1400 Alternate MAC: disabled Ethernet connection type: auto-negotiate *** E-mail Mail server: 0.0.0.0 Unit Domain Recipient 1: Recipient 2: Aeroflex / Weinschel...
  • Page 22 IP Address : (000) 10.(000) 100.(000) 103.(000) 1 Set Gateway IP Address (N) ? Netmask: Number of Bits for Host Part (0=default) (0) 8 Set DNS Server IP addr (N) ? Change telnet config password (N) ? Aeroflex / Weinschel...
  • Page 23 Reply from 10.100.103.49: bytes= 32 time< 1ms TTL= 64 Ping statistics for 10.100.103.49: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 7ms, Average = 1ms Aeroflex / Weinschel...

  • Page 24: Serial Operation

    6853unasserts the RTS signal while command execution is in progress. For those systems incorporating local front panel controls, the serial port can lockout local users, providing a Remote/ Local function similar to that of GPIB operation. Aeroflex / Weinschel...

  • Page 25: 5-2.1. Rs-232 Operation

    Signals DTE is on-line output Ground unused Signals DTE is ready output Signals DCE is ready input unused The DTR signal is asserted when power is on, indicating that the unit is ready. RS232 9-pin DB9 Pinout Null Modem Cable Aeroflex / Weinschel...

  • Page 26: Status Reporting

    Output Queue has been lost Request Control: The device is requesting control (not implemented) Operation Complete: This bit is generated in response to an *OPC command. It indicates that the ITS 2000 has completed all pending operations. Aeroflex / Weinschel...

  • Page 27: General Syntax Structure

    ’0’ and ’1’ preceded by the characters ’#B’, and exadecimal data is comprised of the digits ’0’-’9’, and the letters ’A’-’F’, preceded by the characters ’#H’ or the C language style prefix ’0x’. Examples: 123 (integer) #H55 (hex) 0xAA (hex) #B1010 (binary) Aeroflex / Weinschel...

  • Page 28: 5-4.3. Output Data Format

    One and only one of the enclosed entries must be selected unless the field is also surrounded by brackets, in which case it is optional. Ellipses indicate that the preceding argument or parameter may be repeated. [,...] The preceding item may be repeated, but each repetition must be separated by a comma. Aeroflex / Weinschel...

  • Page 29: Common Commands

    This function is used to read the system identification information, which is a string consisting of the Remarks: following data: manufacturer, model, serial number, and firmware version. mfg integer count of devices Return Value: *IDN? returns the following ’Weinschel,8311 Series, 123, 1.00A’ Example(s): Aeroflex / Weinschel...
  • Page 30 Remarks: This function prevents the8311 Series from executing any further commands or queries until there are no pending operations. The 8311 Series executes all commands sequentially, and does not allow overlapping commands. Return Value: none *WAI Example(s): Aeroflex / Weinschel...

  • Page 31: General Commands

    REF; REL 1 sets the reference, and turns on relative mode Example(s): REF? Function: Read reference setting Syntax: REF? Argument(s): none Remarks: This function reads the reference setting of the currently selected channel. Return Value: refatten real reference attenuation value, in dB Example(s): REF? returns ’30.00’ Aeroflex / Weinschel...
  • Page 32 Example(s): INCR Decrements attenuation DECR Function: INCR Syntax: none Argument(s): Remarks: This function decrements the attenuation setting of the current channel by the value of the attenuator’s programmed stepsize (see STEPSIZE command). Return Value: none Example(s): DECR Aeroflex / Weinschel...

  • Page 33: Inspection

    Pressure should be restricted to a maximum 15 psi to avoid personal injury. c. When parts are thoroughly clean, dry parts using 5 psi of clean moisture free compressed air or preferably dry nitrogen (pressurized spray will work well). Aeroflex / Weinschel...

  • Page 34: 6-3.3. Machined Surfaces And Hardware

    Exercise care to ensure no metal filing or residue remains inside the connector and the connector is thoroughly dry. Where rust, corrosion, and/or oxide deposits are present in large quantities, replace the connector. Aeroflex / Weinschel...

  • Page 35: Line Voltage Fuse Replacement

    Slide out Fuse Drawer located in the center of the Power Entry Module Assembly. d. Remove defective fuse and replace with the correct fuse (Refer to applicable parts list for fuse part number). e. Snap the Fuse Drawer shut and re-connect ac power cord. Aeroflex / Weinschel...

  • Page 36: Replacable Parts List

    (this information is on the component side of the PCB). 7-3 DRAWING NUMBER: The Aeroflex / Weinschel part number consists of a basic number with a dash number. The basic number should cross reference to a drawing number for most of the items. For those items that do not have a drawing number, the manufacturers part number is provided.

  • Page 37: Model 8310-1-3-Tn Attenuator Unit Assembly Replaceable Parts List (P/N 193-7001-6)

    W /ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W /ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7001-4, Rev. A for parts location. Model 8310-1-2-FN / -RN, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7002-5, Rev. A): Find Part Number...
  • Page 38 MODEL 8310, +15V W /ETHERNET 089-4052 ICD, ATTEN UNIT MODEL 8310 (75 OHM) W /ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W /ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7001-6, Rev. A for parts location. Aeroflex / Weinschel...

  • Page 39: Model 8310-2-Fn / -Rn, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7002-3)

    W /ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W /ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7002-3, Rev. A for parts location. Model 8310-2-2-FN / -RN, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7002-4, Rev. A): Find Part Number...

  • Page 40: Model 8310-35-Fn / -Rn Attenuator Unit Assembly Replaceable Parts List (P/N 193-7035-9)

    ICD, ATTEN UNIT, 8310 W/ETHERNET IM493 O & S MANUAL MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7035-9, Rev. A for parts location. Model 8310-35-2-FN / -RN Attenuator Unit Assembly Replaceable Parts List (P/N 193-7035-10, Rev. A): Find...
  • Page 41 ICD, ATTEN UNIT, 8310 W/ETHERNET IM493 O & S MANUAL MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7035-11, Rev. A for parts location. Model 8310-35-4-TN Attenuator Unit Assembly Replaceable Parts List (P/N 193-7035-12, Rev. A): Find Part Number...
  • Page 42 ICD, ATTEN UNIT, 8310 W/ETHERNET IM493 O & S MANUAL MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7035-13, Rev. A for parts location. Model 8310-35-2-F / R -EN, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7035-14, Rev. A): Find...
  • Page 43 ICD, ATTEN UNIT, 8310 W/ETHERNET IM493 O & S MANUAL MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7035-15, Rev. A for parts location. Model 8310-35-4-T-EN, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7035-16, Rev. A): Find Part Number...

  • Page 44: Model 8310-36-Fn / -Rn Attenuator Unit Assembly Replaceable Parts List (P/N 193-7036-8)

    ICD, ATTEN UNIT, W /ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W /ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7036-8, Rev. A for parts location. Model 8310-36-2-FN / -RN Attenuator Unit Assembly Replaceable Parts List (P/N 193-7038-9, Rev. A): Find Part Number...
  • Page 45 SCR PAN HD SELFLOCK, 4-40 X 1/4 193-8135 WIRING DIAGRAM, ATTEN UNIT MODEL 8310, +15V W/ETHERNET 089-4051 ICD, ATTEN UNIT, W/ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7038-10, Rev. A for parts location. Aeroflex / Weinschel...

  • Page 46: Model 8310-36-2-Fn / -Rn Attenuator Unit Assembly Replaceable Parts List (P/N 193-7036-9)

    ICD, ATTEN UNIT, W /ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W /ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7036-11, Rev. A for parts location. Model 8310-36-2-F-EN / -R-EN Attenuator Unit Assembly Replaceable Parts List (P/N 193-7038-12, Rev. A): Find Part Number...

  • Page 47: Model 8310-38-3-Tn Attenuator Unit Assembly Replaceable Parts List (P/N 193-7038-11)

    SCR PAN HD SELFLOCK 4-40 X 1/4 193-8135 WIRING DIAGRAM, ATTEN UNIT MODEL 8310, +15V W/ETHERNET 089-4051 ICD, ATTEN UNIT, W/ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7038-13, Rev. A for parts location. Aeroflex / Weinschel...

  • Page 48: Model 8310-38-4-Tn, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7038-12)

    ICD, ATTEN UNIT, W /ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W /ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7038-9, Rev. A for parts location. Model 8310-38-2-FN / -RN Attenuator Unit Assembly Replaceable Parts List (P/N 193-7038-10, Rev. A): Find Part Number...

  • Page 49: Model 8310-38-2-F / R -En, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7038-14)

    193 8135 WIRING DIAGRAM, ATTEN UNIT    MODEL 8310, +15V W/ETHERNET 089 4051 ICD, ATTEN UNIT, W/ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310   W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7038-, Rev. A for parts location. Model 8310-38-4-TN, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7038-12, Rev. A): Find Part Number Description Quantity Reference CAGE...

  • Page 50: Model 8310-38-4-En, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7038-16)

    ICD, ATTEN UNIT, W /ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W /ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7038-13, Rev. A for parts location. Model 8310-38-2-F / R –EN, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7038-14, Rev. A): Find Part Number...
  • Page 51 ICD, ATTEN UNIT W /ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W /ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7038-15, Rev. A for parts location. Model 8310-38-4-T-EN, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7038-16, Rev. A): Find Part Number...

  • Page 52: Model 8310-138-Fn / -Rn, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7138-5)

    SCR PAN HD SELFLOCK 4-40 X 1/4 193-8136 WIRING DIAGRAM, ATTEN UNIT 8310 +5V W/ETHERNET 089-4066 ICD, ATTEN UNIT, MODEL 8310 (+5V) W/ETHERNET IM493 O & S MANUAL, MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7138-5, Rev. A for parts location. Aeroflex / Weinschel...
  • Page 53 SCR PAN HD SELFLOCK 4-40 X 1/4 193-8136 WIRING DIAGRAM, ATTEN UNIT 8310 +5V W/ETHERNET 089-4066 ICD, ATTEN UNIT, MODEL 8310 (+5V) W/ETHERNET IM493 O & S MANUAL, MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7403-6, Rev. A for parts location. Aeroflex / Weinschel...
  • Page 54 SCR PAN HD SELFLOCK 4-40 X 1/4 193-8136 WIRING DIAGRAM, ATTEN UNIT 8310 +5V W/ETHERNET 089-4066 ICD, ATTEN UNIT, MODEL 8310 (+5V) W/ETHERNET IM493 O & S MANUAL, MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7403-7, Rev. A for parts location. Aeroflex / Weinschel...
  • Page 55 SCR PAN HD SELFLOCK 4-40 X 1/4 193-8136 WIRING DIAGRAM, ATTEN UNIT 8310 +5V W/ETHERNET 089-4066 ICD, ATTEN UNIT, MODEL 8310 (+5V) W/ETHERNET IM493 O & S MANUAL, MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7403-8, Rev. A for parts location. Aeroflex / Weinschel...

  • Page 56: Model 8310-352-Fn / -Rn, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7403-5)

    WIRING DIAGRAM, ATTEN UNIT 8310 +15V W/ETHERNET 089-4065 ICD, ATTEN UNIT DC TO 6 GHz W/ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7403-5, Rev. A for parts location. Aeroflex / Weinschel...

  • Page 57: Model 8310-352-2-Fn / -Rn, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7403-6)

    WIRING DIAGRAM, ATTEN UNIT MODEL 8310, +15V W/ETHERNET 089-4065 ICD, ATTEN UNIT, DC TO 6 GHz W/ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7403-6, Rev. A for parts location. Aeroflex / Weinschel...

  • Page 58: Model 8310-352-3-Tn, Attenuator Unit Assembly Replaceable Parts List (P/N 193-7403-7)

    WIRING DIAGRAM, ATTEN UNIT 8310 +15V W/ETHERNET 089-4065 ICD, ATTEN UNIT, DC TO 6 GHz W/ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7403-7, Rev. A for parts location. Aeroflex / Weinschel...
  • Page 59 WIRING DIAGRAM, ATTEN UNIT 8310 +15V W/ETHERNET 089-4065 ICD, ATTEN UNIT, DC TO 6 GHz W/ETHERNET (+15V) IM493 O & S MANUAL, MODEL 8310 W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-7403-8, Rev. A for parts location. Aeroflex / Weinschel...
  • Page 60 NUT HEX #2 CRES SMALL PATTERN MS15795-802 WASHER FLAT .094 ID, .250 OD NAS1676C2 WASHER LOCK #2 193-8135 WIRING DIAGRAM ATTEN UNIT MODEL 8310 +15V W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-8034-3, Rev. A for parts location. Aeroflex / Weinschel...
  • Page 61 NUT HEX #2 CRES SMALL PATTERN MS15795-802 WASHER FLAT .094 ID, .250 OD NAS1676C2 WASHER LOCK #2 193-8136 WIRING DIAGRAM ATTEN UNIT MODEL 8310 +5V W/ETHERNET Refer to Aeroflex / Weinschel Drawing 193-8034-4, Rev. A for parts location. Aeroflex / Weinschel...

  • Page 62: Contacting Aeroflex / Weinschel

    9. AEROFLEX / WEINSCHEL WARRANTY: PRODUCTS – Aeroflex / Weinschel warrants each product it manufactures to be free from defects in material and workmanship under normal use and service anywhere in the world. Aeroflex / Weinschel’s only obligation under this Warranty is to repair or replace, at its plant, any product or part thereof that is returned with transportation charges prepaid to Aeroflex / Weinschel by the original purchaser within ONE YEAR from the date of shipment.
  • Page 82 APPENDIX A APPENDIX A CARE AND HANDLING OF MICROWAVE COAXIAL CABLE ASSEMBLIES A-1 CARE AND HANDLING OF ASSEMBLIES. A-3 MAKING INITIAL CONNECTIONS. To ensure accurate measurements and optimal Exercise caution when mating cables. Poor connections performance of Weinschel products, the microwave coaxial lead to poor system performance.
  • Page 83 CARE & HANDLING OF COAXIAL CABLES A-4.2 HEX-NUT TYPES. To mate a connector of the A-5.1 SECURING CABLES. Use toothed, rubber-lined hex-nut type, always use a torque wrench set to the correct "P-clamps" to hold cables in place. If it is necessary to use torque value.
  • Page 84 All New Units 1/09 Added Model 8310-35-XN Series All New Models 4/18/11 Incorporated Aeroflex / Weinschel ECN 11-079. All Models ECN adds additional operation instructions for the Lantronix XPort™ Ethernet. Changed Storage Temperature to 4° to +167 °F (-20° to +75 °C)
  • Page 85 EC DECLARATION OF CONFORMITY This is to certify that the: SmartStep Attenuator Unit 8310 Series Manufactured by: Weinschel Corporation Conforms with the protection requirements of Council Directive 89/336/EEC and the Amending Directive 93/68/EEC, relating to Electromagnetic Compatibility and Council Directive 73/23/EEC relating to LVD (Safety), by the application of: EN50081-1: 1992 Generic Emissions Standard.

Table of Contents