Toshiba B-EX4T2 Series Manual page 52

7. SUPPLY SPECIFICATIONS
Max.
7. effective
print width
Label
Effective
8.
print length
Tag
Slow-up and
down area
9.
(Un-print
Slow-down
area)
Paper
10.
thickness
Paper
11. thickness
can be cut
12. Max. paper roll diameter
13. Paper winding direction
14. Paper core
NOTES:
1. To ensure print quality and print head life use only TOSHIBA TEC specified media.
2. When using the peel-off at 12"/sec or more for 203dpi model, issue at 10"/sec.
When using the peel-off at 10"/sec or more for 300dpi model, issue at 8"/sec.
3. When using the disk cutter, the label length must meet the following condition:
≧
Label length 18.0mm - (Gap length/2).
4. For label issues, set the head lever to position LABEL.
5. For tag issues, set the head lever to position TAG.
6. When using narrow paper, may need to set the head lever to position TAG, or need to adjust the right
head pressure.
7. The ratio of a label length to a gap length must be a minimum of 3 to 1 (3:1).
8. The paper width for the label includes its backing paper.
9. When using label stock in cut mode, be sure to cut in the gaps. Cutting labels will cause the adhesive to
stick to the cutter, which may affect the cutter performance and shorten the cutter life.
10. In the cut issue mode, the backing paper of labels (the gap between labels) can be cut. The label itself
cannot be cut. When the perforated label is used, it is necessary to test and confirm the cutting performance
beforehand.
11. In the cut issue mode, the gap length must be 6 mm or more, and the cut position must be adjusted so that
the cutter cuts in the center of the gap.
12. When the stop position is not proper, the print stop position should be changed by the strip position fine
adjustment.
13. When the gap between labels is 5 mm or more, the effective print length should be set to the maximum
value (Label pitch minus 2 mm), then the print stop position should be changed by the strip position fine
adjustment.
14. If paper is jammed at the platen when cut issue is performed, enable the forward feed function ("FORWARD
WAIT") in system mode.
15. When the paper thickness is more than 200 µm, the print head installation position may need to be
changed.
Max. 104.0 +-0.2
Min. 6.0 11.0
Max. 1496.0 252.0
－
Min. 8.0
－
Max. 1498.0
Slow-up
Min. 0.13
Max. 0.17
Min. -
Max. -
φ200
(φ180 when then built-in
rewinder is used)
Inside the printing side
(STD.)
Inside diameter
φ76.2±0.3
17.0 6.0
1492.0 1496.0
19.0 8.0
1498.0 1498.0
1.0
1.0
0.08 -
0.17 -
(φ180 when then built-in
rewinder is used)
Inside the printing side
Inside diameter
47
104.0 +-0.2
11.0 17.0 6.0
252.0 1492.0 496.0
－
19.0 8.0
－
1498.0 498.0
1.0
1.0
0.13
0.17
0.08
0.17
φ200
(φ180 when then built-in
Inside the printing side
(STD.)
φ76.2±0.3
104.0 +-0.2
11.0 17.0
252.0 492.0
－
19.0
－
498.0
1.0
1.0
0.13
0.17
- 0.08
- 0.17
φ200
rewinder is used)
(STD.)
Inside diameter
φ76.2±0.3