Table of Contents
Advertisement
Quick Links
EC 06/42
http://www.dropsa.com
Via Benedetto Croce, 1
Vimodrone, MILANO (IT)
t. +39 02 250791
Mini-SUMO PUMP
User Operating and
Maintenance Manual
Original text translation
CONTENT
1.
2.
3.
IDENTIFICATION OF THE MACHINE
4.
TECHNICAL FEATURES
5.
6.
7.
8.
PROBLEMS AND SOLUTIONS
9.
10.
11.
12.
13.
14.
15.
OPERATIONAL HAZARDS
The manual has been prepared in compliance with Directive
CE 06/42
Dropsa products can be purchased from Dropsa branches and authorized
distributors,
visit www.dropsa.com/contact or contact us sales@dropsa.com
C2158IE WK 03/17
Advertisement
Table of Contents
Related Manuals for DROPSA Mini-SUMO
Summary of Contents for DROPSA Mini-SUMO
-
Page 1: Table Of Contents
The manual has been prepared in compliance with Directive C2158IE WK 03/17 CE 06/42 EC 06/42 http://www.dropsa.com Via Benedetto Croce, 1 Dropsa products can be purchased from Dropsa branches and authorized Vimodrone, MILANO (IT) distributors, visit www.dropsa.com/contact or contact us sales@dropsa.com t. +39 02 250791... -
Page 2: Introduction
2.GENERAL DESCRIPTION The Mini-SUMO lubrication pump series is particularly suited for dual line systems and progressive systems and can be adapted to many needs without making mechanical changes, even after installation is complete. In fact, by selecting from a set of components that are perfectly compatible with each other and easily assembled, it is possible to vary the pressure, the quantity of the delivered lubricant, the type of lubricant and the type of distribution. - Page 3 Max continuous operating time at maximum pressure 10min with pause of 30 min. (ratio 1:3) With 24 V cc motor With single-phase 230 V-50 hz motor With single-phase 110 V-50 hz motor If a different product is used, please contact Dropsa S.p.A. to ensure it is suitable for use.
- Page 4 4.1 HYDRAULIC SYSTEM The hydraulic diagrams related to the different configurations that can be obtained using the available accessories are shown below (see paragraph 11) Oil loading cap with filter Minimum Min. laser level float level Max visible level NO o NC visible level G½”...
- Page 5 Oil loading cap Min. laser level with filter NO o NC visible level Max visible level Minimum float level G½” BSP Lubricant loading 0-380 Electromagnetic switch 300 µ Electromagnetic switch 25 CC/MIN G3/8” BSP Pmax 380 BAR Line 1 Line 2 0.18 kw –...
-
Page 6: Machine Components
5. MACHINE COMPONENTS 5.1. STANDARD PUMP COMPONENTS 5.1.1 FIXED FLOW RATE PUMPING ELEMENTS The pump may be configured with two fixed flow rate pumping elements (25 cm^3/ min for each pumping element. The seal between the piston and pumping element casing is dry, as the insertion of a gasket is not required. The check valve for the pumping element is has a cone-shaped seal. - Page 7 5.1.2 MINIMUM AND MAXIMUM GREASE LEVEL INDICATORS The standard grease pumps have two level types: • Minimum laser level (for 10 and 30 Kg reservoir); • Max visible level (floating). 5.1.3 Minimum laser level The minimum level is realised by a laser probe. When the lubricant reaches minimum level, the laser probe signals the lack of lubricant.
- Page 8 5.2.4 ELECTRIC EQUIPMENT “DROPSA” electric equipment has been designed with the purposes of supplying a system that is complete with all commands necessary for the automatic operation controlled by safety signals for centralised lubrication systems. The primary voltage is 400 VAC and 50 Hz, other voltages are provided upon request.
-
Page 9: Unpacking And Installation
• Use safety gloves or glasses as specified in the safety sheet for the lubricating oil • DO NOT use aggressive lubricants with NBR gaskets. In the case of doubt, contact the Dropsa SpA technical office to receive a detailed card about the recommended oils. - Page 10 7.2.1 LASER PROBE SETTING, 24V CC OUT NO E NC (1 threshold) 1. Reference notch. 2. Yellow led: lights when the set value is reached, (outlet=ON). 3. Lock ring. 4. Setting lock ring (be adjusted manually after unlocking). 5. Green led: indicates the correct power supply (24V cc). * To obtain a correct setting bring the lock ring to maximum setting value and then down to desire value.
- Page 11 Absolute 1 threshold maximum level Absolute 2 threshold minimum level NOTE: To change calibration thresholds of laser and ultrasound probes contact DROPSA staff 8. PROBLEMS AND SOLUTIONS ATTENTION The machine may only be opened and repaired by authorised Dropsa personnel.
-
Page 12: Maintenance Procedures
If you were not able to solve the problem after consulting the diagnostics table, do not try to find the fault by disassembling machine parts but contact the Dropsa technical office and report the anomalies that have been discovered, with a detailed description. -
Page 13: Disposal
In the case of doubts and/or problems that cannot be solved, do not try to discover the reason by disassembling machine parts, but contact the DROPSA S.p.A technical office. 10. DISPOSAL During machine maintenance, or if it is demolished, do not dispose of the polluting parts in an improper manner. Refer to the local regulations for their correct disposal. -
Page 14: Order Information
MINISUMO OIL Pump, 30 Kg 1ph-0. 25kw - 230V 2487064 MINISUMO OIL Pump, 30 Kg 24V Cc 2487065 DESCRIPTION DROPSA CODE CODE STANDARD GREASE VERSION with laser sensor 24V 0295131 cc Out NO e NC (1 threshold) (per 10/30 kg) - Page 15 Order CODE For MINISUMO OIL PUMP, 30 Kg Code Example For MINISUMO OIL PUMP, 30 Kg Code 2487050 Minimum Level STANDARD OIL VERSION With Floating Reed 0295150 Laser sensor 24V cc Out NO e NC (1 threshold) 0295131 Maximum Level Pumping Element Two Fixed Flow Rate Pumping Elements 0297010-0297010...
-
Page 16: Dimensions
12. DIMENSIONS 10 Kg 30 Kg 344,5 533,5... -
Page 17: Handling And Transport
13. HANDLING AND TRANSPORT Transport and storage are carried out using a metal pallet with packaging on the side and a wood cover. The pump is fixed on a metal pallet that permits safe handling with a transpallet or fork lift truck. The metal pallet was designed to be installed in the plant. - Page 18 Fire – explosion – damage to the gaskets Corrosive products Pump corrosion - damage to people Water Pump oxidation Food substances They would be contaminated * For more detailed information regarding product compatibility with particular fluids, contact the Dropsa S.p.A. technical office...
Need help?
Do you have a question about the Mini-SUMO and is the answer not in the manual?
Questions and answers
for single grease outlet system,air connection required or not
No, the DROPSA SUMO single grease outlet system does not require an air connection. It operates using a DC motor with gearbox and does not mention any need for an air supply.
This answer is automatically generated