DROPSA LOCOPUMP S3 User And Maintenance Manual

DROPSA LOCOPUMP S3 User And Maintenance Manual

Pneumatic pump

Advertisement

http://www.dropsa.com
Via Benedetto Croce, 1
Vimodrone, MILANO (IT)
t. +39 02 250791
LOCOPUMP S3
Pneumatic Pump
User and Maintenance
Manual
Original text translation
INDEX
1.
INTRODUCTION
2.
GENERAL DESCRIPTION
3.
PRODUCT IDENTIFICATION
4.
TECHNICAL CHARACTERISTICS
5.
COMPONENTS
6.
UNPACKING AND INSTALLING
7.
OPERATING INSTRUCTIONS
8.
TROUBLESHOOTING
9.
MAINTENANCE PROCEDURE
10.
DISPOSAL
11.
ORDERING INFORMATION
12.
DIMENSIONS
13.
HANDLING AND TRANSPORTATION
14.
OPERATING HAZARDS
15.
PRECAUTIONS
Manual compiled in accordance with Directive CE 06/42
Dropsa products can be purchased from Dropsa branches and authorized distributors,
www.dropsa.com/contact or contact us sales@dropsa.com
C2255IE WK 13/18
visit

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LOCOPUMP S3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for DROPSA LOCOPUMP S3

  • Page 1 Manual compiled in accordance with Directive CE 06/42 C2255IE WK 13/18 Via Benedetto Croce, 1 Vimodrone, MILANO (IT) t. +39 02 250791 Dropsa products can be purchased from Dropsa branches and authorized distributors, visit www.dropsa.com/contact or contact us sales@dropsa.com...
  • Page 2: General Description

    2. GENERAL DESCRIPTION The pneumatic pump “LOCOPUMP S3” uses compressed air to control the grease quantity which is delivered from the pump. Hence, it should be used on machines where compressed air is readily available.
  • Page 3 5. COMPONENTS The main parts of the pump are: The reservoir constructed of transparent type plastic, compatible with commercially available greases. The pump body, constructed of steel with capability of delivery up to 2 cm³ (0,12 cu.in) per stroke at a maximum pressure of 300 bar (4351 psi).
  • Page 4: Overall Dimensions

    5.1 PNEUMATIC GREASE PUMP WITH STANDARDIZED 400CC LUBRICANT CARTRIDGE LOADING SYSTEM The Pneumatic Pump with cartridge grease loading is a pump for general use in single line progressive divider lubrication systems such as SMX, SMO, SMP or SMPM. The pump is designed for all those applications where it is ideal to have grease supplied in readily available cartridges.
  • Page 5: Unpacking And Installation

    6.5 AIR CONNECTION ON PUMP Use an 1/8” BSP connection fitting. It also possible to use DropsA’s nut an cone fittings as the seating is already available. Remember to use a 3/2 valve that allows the air to vent to atmosphere and the internal spring within the pump to reset.
  • Page 6: Problems And Solutions

    Use gloves and safety glasses as advised in the grease lubricant safety data sheet.  DO NOT use aggressive lubricants on the NBR seals, if in doubt consult DropsA Spa technical office who can offer advice on lubricants and provide a pre-approved list of greases.
  • Page 7: Maintenance Procedures

    Ensure you have necessary personal protective equipment to avoid any contact with the grease. The pump undergoes severe factory testing therefore no maintenance is forecasted with the pump. DropsA recommends the use of lubricants that are free of any impurities as well as a regular cleaning of the pump’s components.
  • Page 8 12. DIMENSIONS To facilitate future maintenance, increase the spaces indicated by at least 100 mm. Ø11 LUBRICANT OUTLET G1/4" BSP AIR INLET G1/8" BSP Compression fitting for Ø 6 pipe LUBRICANT INLET Valved Greaser UNI 7663-"A" - 1/8" 2 Kg 0.5 Kg...
  • Page 9 13. HANDLING AND TRANSPORT Prior to shipping, the equipment is carefully packed in cardboard package. During transportation and storage, always maintain the pump the right way up as indicated on the box. On receipt check that package has not been damaged. Then, store the machine in a dry location.

Table of Contents