Kenwood NX-3400 Service Manual page 8

2.2.8.2 Data Writing
Before moving to next Zone/Channel, "Keep This Change?"
appears on the LCD, if you select "OK", the new data is written
to memory. If you select "Cancel", the new data not be written;
the new data will be erased.
The setup items for Front panel programming mode are as
follows.
No. Setup item Display
1 RX Frequency RX Frequency Receive Frequency
2 TX Frequency TX Frequency Transmit Frequency
3 Channel Type Channel Type Analog/NXDN/DMR
4 Transmit Mode*3 Transmit Mode Analog/NXDN/DMR
5 Channel Channel Space Analog:
Spacing
6 RX Signaling RX QT/DQT
Button operation (1/3)
Button\ Zone
Item Select
[ ] Decision Decision
[ ] Unused Back to the
previous item
[ ] Unused Unused
[ ] Exit panel Exit panel
program mode program mode
[] Zone change Channel
change
[] Zone change Channel
change
[] Unused Unused
[] Unused Unused
Keypad Zone number Channel
[0] ~ [9] select number select
Keypad Decision Decision
[*]
Keypad Unused Back to the
[#] previous item
*5: Mixed Mode only
*6: [1] = "Analog", [2] = "NXDN" for System type or "DMR" for System type DMR, [3] = "Mixed"
*7: [1] = "Analog", [2] = "NXDN" for System type NXDN or "DMR" for System type DMR
*8: [1] = "12.5kHz", [2] = "25kHz" for System type Analog or "6.25kHz" for System type NXDN, [3] = "20kHz" for System type Analog
1-8 (No.RA070<Rev.001>)
Remarks
12.5kHz/20kHz/25kHz*4
NXDN:
6.25kHz/12.5kHz
DMR: 12.5kHz
Receive QT/DQT
Channel RX
Select Frequency
Decision
Back to the
previous item
Unused
Exit panel
program mode
Frequency up Frequency up Channel type
Frequency
down
Frequency
step change
Frequency
step change
Entry a Frequency directly
Decision
Back to the
previous item
No. Setup item
7 TX Signaling
8 RX RAN
9 TX RAN
10 Color Code
11 Slot Selection
12 Transmit Power Transmit
13 Channel Name
*3: In "Channel Type" display, "Transmit Mode" can be
entered only when Mixed mode is selected.
*4: When the transmission/reception frequency is set more
than 900 MHz or more, the Channel Spacing is fixed to
12.5 kHz.
TX Channel Type
Frequency
Decision Decision
Back to the Back to the
previous item previous item
TX Frequency Unused
OFF
Exit panel Exit panel program
program mode mode
change
Frequency Channel type
down change
Frequency Unused
step change
Frequency Unused
step change
Channel Type
select
([1], [2] or [3]) *6
Decision Decision
Back to the Back to the
previous item previous item
Display Remarks
TX QT/DQT Transmit QT/DQT
RX RAN None, 1~63
TX RAN None, 1~63
Color Code 0 ~15
Slot Selection Slot 1, Slot 2, Auto
Low/Medium/High
Power
Channel Name
Transmit Mode *5 Channel
Spacing
Decision Decision
Back to the Back to the
previous previous item
item
Unused Unused
Exit panel program Exit panel
mode program mode
Transmit Mode Channel Spacing
Change Change
Transmit Mode Channel Spacing
Change Change
Unused Unused
Unused Unused
Transmit Mode Channel spacing
select select
([1] or [2]) *7 ([1], [2] or [3]) *8
Decision Decision
Back to the Back to the
previous item previous item