Advertisement
2.2.7 Clone Mode
Programming data can be transferred from one transceiver to
another by connecting them via their external universal
connectors. The operation is as follows.
The following data cannot be cloned.
• Tuning data
• Transceiver Embedded Message
• ESN (Electronic Serial Number) data
Button guide on the Clone/ Front Panel Programming
Password input screen.
• Confirm ([
] button): The password confirmation
• Delete ([
] button): Delete the latest digit from the current
password number (Press and hold to delete all password
numbers)
• Select([
] button): Determine the latest digit of the
password number.
(1) In the source transceiver, enter the clone mode by using
section "2.2.2 How to Enter Each Mode". When the Clone/
Front Panel Programming Password is set to the
transceiver, "Input Password" is displayed on the LCD.
If the password is not set, the transceiver displays "CLONE
MODE".
(2) When you enter the correct password, "CLONE MODE" is
displayed, the transceiver can be used as the cloning
source. The following describes how to enter the
password.
(3) There are two methods to enter the password as follows.
- How to enter the password using the keypad;
If one of the buttons 0 to 9 is pressed while the "Input
Password" is displayed, the password number is
displayed on the LCD.
Each press of the button shifts the display in order to the
left.
When you enter the password and press [
button, "CLONE MODE" displayed if the entered
password is correct. If password is incorrect, "Input
Password" is redisplayed.
- How to enter password using the [] and []
buttons;
If the [] / [] button is pressed while "Input Password"
is displayed, the Clone/ Front Panel Programming
Password input screen is displayed.
If the [] or [] button is pressed while the clone/ Front
Panel Programming Password input screen is displayed,
the number (0 to 9) blinks on the LCD. When you press
the [
] button, currently selected number is
determined. If you press the [
password in this procedure, "CLONE MODE" is
displayed if entered password is correct. If the password
is incorrect, "Input Password" is redisplayed.
(4) Power ON the target transceiver.
(5) Connecting the cloning cable (part No.E30-3325-05) to the
universal connectors on the source and target.
(6) Press [
] button on the source while the source displays
"CLONE MODE". The data of the source is sent to the
target. While the target is receiving the data, "PROGRAM"
is displayed. When cloning of the data is completed, the
source displays "END", and the target automatically
operates in the User mode. The target can then be
operated by the same program as the source.
Note:
2.2.8 Front Panel Programming Mode
If the Front Panel Programming Mode is used, the frequency or
other data of the conventional channel is rewritable only by the
transceiver.
Moreover, the conventional channel can be added.
The following setup items can be changed or added by
using the Front panel programming mode.
] or [*]
Button guide on the Clone/ Front Panel Programming
Password input screen.
] button after entering
2.2.8.1
Press the PF button which is assigned as "Panel Program" by the
FPU, or select the "Panel Program" which is assigned into the
Menu button by the FPU.
If the Clone/Front panel programming Password is not set to the
transceiver, "Panel Program" is displayed on the LCD.
If the Clone/Front panel programming Password is set to the
transceiver, "Panel Program" is displayed on the LCD when you
enter the correct password while "Input Password" is displayed.
(7) The other target can be continuously cloned. When the
[
] button on the source is pressed while the source
displays "END", the source displays "CLONE MODE".
Carry out the operation in step (4) to (6).
• Cannot be cloned if the Password (Write) is programmed to
the target.
• "Model name" must be same to clone the transceiver.
Fig.2
• RX/TX Frequency
• Channel Type
• Transmit Mode (Mixed mode only)
• Channel Spacing
• Decode QT/DQT/RAN, Encode QT/DQT/RAN
• Color Code
• Slot Selection
• Transmit Power
• Channel Name
• Confirm ([
] button): The password confirmation
• Delete ([
] button): Delete the latest digit from the current
password number (Press and hold to delete all password
numbers)
• Select ([
] button): Determine the latest digit of the
password number.
How to enter the Front panel programming mode
Cloning cable
(E30-3325-05)
(No.RA070<Rev.001>)1-7
Hide quick links:
Advertisement
